Shark VERTEX MultiFLEX DuoClean PowerFins Cordless Vacum with Self-Cleaning Brushroll Owner’s Manual

IMPORTANT SAFETY INSTRUCTIONS

FOR HOUSEHOLD USE ONLY • WHEN USING AN ELECTRICAL APPLIANCE, BASIC PRECAUTIONS SHOULD ALWAYS BE FOLLOWED, INCLUDING THE FOLLOWING. PLEASE READ ALL INSTRUCTIONS BEFORE USING THIS VACUUM.If the charging cord plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. DO NOT force into outlet or try to modify to fit.To reduce the risk of shock and unintended operation, turn off power and remove the Li-Ion battery before servicing.

WARNINGTo reduce the risk of fire, electric shock, injury, or property damage:THE FLOOR NOZZLE, WAND, AND HANDHELD VACUUM CONTAIN ELECTRICAL CONNECTIONS:

This vacuum consists of a motorized nozzle, wand, and handheld vacuum. These components contain electrical connections, electrical wiring, and moving parts that potentially present risk to the user.
Before each use, carefully inspect all parts for any damage. If a part is damaged, discontinue use.
Use only identical replacement parts.
This vacuum contains no serviceable parts.
Use only as described in this manual.DO NOT use the vacuum for any purpose other than those described in this manual.
With the exception of the filters and dust cup, DO NOT expose any parts of the vacuum to water or other liquids.
Keep the appliance and its cord out of reach of children. Do not allow the appliance to be used by children.DO NOT allow to be used as a toy. Close supervision is necessary when used near children.GENERAL USE
This appliance can be used by persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved. Cleaning and user maintenance shall not be made by children.
Always turn off the vacuum before connecting or disconnecting any current-carrying hoses, motorized nozzles, chargers, batteries, or other electrical or mechanical parts.
DO NOT handle plug or vacuum with wet hands.
DO NOT use without dust cups, filter, and brush roll in place.
Only use Shark® branded filters and accessories. Failure to do so will void the warranty.
DO NOT put any objects into nozzle or accessory openings. DO NOT use with any opening blocked; keep free of dust, lint, hair, and anything that may reduce airflow.
DO NOT use if nozzle or accessory airflow is restricted. If the air paths or the motorized floor nozzle become blocked, turn the vacuum off. Remove all obstructions before you turn on the unit again.
Keep nozzle and all vacuum openings away from hair, face, fingers, uncovered feet, or loose clothing.
DO NOT use if vacuum is not working as it should, or has been dropped, damaged, left outdoors, or dropped into water.
Use extra care when cleaning on stairs.
DO NOT leave the vacuum unattended while powered on.
When powered on, keep the vacuum moving over the carpet surface at all times to avoid damaging the carpet fibers.
DO NOT place vacuum on unstable surfaces such as chairs or tables.
DO NOT use to pick up:a) Liquidsb) Large objectsc) Hard or sharp objects (glass, nails, screws, or coins)d) Large quantities of dust (including drywall, fireplace ash, or embers). DO NOT use as an attachment to power tools for dust collection.e) Smoking or burning objects (hot coals, cigarette butts, or matches)f) Flammable or combustible materials (lighter fluid, gasoline, or kerosene)g) Toxic materials (chlorine bleach, ammonia, or drain cleaner)
DO NOT use in the following areas:a) Poorly lit areasb) Wet or damp surfacesc) Outdoor areasd) Spaces that are enclosed and may contain explosive or toxic fumes or vapors (lighter fluid, gasoline, kerosene, paint, paint thinners, mothproofing substances, or flammable dust)
Turn off the vacuum before plugging in or unplugging the charger.
Turn off the vacuum before any adjustment, cleaning, maintenance or troubleshooting.
During cleaning or routine maintenance, DO NOT cut anything other than hair, fibers, or string wrapped around the brushroll.
Allow all filters to air-dry completely before replacing in the vacuum to prevent liquid from being drawn into electric parts.
DO NOT modify or attempt to repair the vacuum or the battery yourself, except as indicated in this manual.DO NOT use the battery or vacuum if it has been modified or damaged. Damaged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion or risk of injury.
Turn off all controls before unplugging.
Always turn off this appliance before connecting or disconnecting motorized nozzle or hand tool.BATTERY PACK
The battery is the power source for the vacuum. Carefully read and follow all charging instructions.
To prevent unintentional starting, ensure the vacuum is powered off before picking up or carrying the vacuum. DO NOT carry the appliance with your finger on the power switch.
Use only Shark® charger DK33-288080H-U. Use of an incorrect charger may result in no charging, and/or unsafe conditions. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.
Keep the battery away from all metal objects such as paper clips, coins, keys, nails, or screws. Shorting the battery terminals increases the risk of fire or burns.
Under abusive conditions, liquid may be ejected from the battery. Avoid contact with this liquid, as it may cause irritation or burns. If contact occurs, flush with water. If liquid contacts eyes, seek medical help.
Battery should not be stored at temperatures below 3°C (37.4°F) or above 104°F (40°C) to maintain long-term battery life.
DO NOT charge battery at temperatures below 5°C (40°F) or above 104°C (104°F). Charging improperly or at temperatures outside of the specified range may damage the battery and increase the risk of fire.
Store the appliance indoors. DO NOT use or store it below 3°C (37.4°F). Ensure the appliance is at room temperature before operating.
DO NOT expose the battery to fire or temperatures above 265°F (130°C) as it may cause explosion.
Use appliances only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.
Disconnect the battery pack from the appliance before making any adjustments, changing accessories, or storing appliance. Such preventive safety measures reduce the risk of starting the appliance accidentally.
For IZ462H/QZ462HQ/IZ482H/IZ483H, use only with Shark battery pack XSBT750.

SAVE THESE INSTRUCTIONS

ASSEMBLY

Insert Wand into Floor Nozzle.
Insert Handheld Vacuum into wand.For proper operation, ensure all components are completely connected and clicked into place.

LI-ION BATTERY

The Lithium Ion Power Pack battery does not come fully charged. Prior to first use, charge completely. During first use, run the battery down until it is completely out of power. This will condition the battery. LED BATTERY POWER AND CHARGING INDICATORS

RECYCLING THE LI-ION BATTERY

This product uses a lithium-ion rechargeable and recyclable battery. When the battery no longer holds a charge, it should be removed from the vacuum and recycled. DO NOT incinerate or compost the battery. When your Lithium ION Power Pack Battery needs to be replaced, dispose of it or recycle it in accordance with local regulations. In some areas, it is illegal to place spent lithium-ion batteries in the bin or in a municipal solid waste stream. Return spent power packs to an authorized recycling center or to retailer for recycling. Contact your local recycling center for information on where to drop off the spent power pack.

To charge, remove the handheld vacuum from the wand by pressing the Wand Release button and pulling up. Plug the charger into the charging port.

Battery Runtime

MINUTES
MODE	IZ440H/IZ441H	IZ462H/QZ462HQ	IZ482H/IZ483H*
Hand Vac	50	60	120
Bare Floor/Standard Mode	34	34	68
Carpet Mode/Standard Mode	23	23	46
Boost Mode (Hand Vac)	10	10	20

*Runtimes are as a result of to two batteries.

CHARGING THE BATTERY

USING THE LI-ION CHARGER

Plug the Li-Ion Charger into a wall outlet.

If your handheld vacuum’s battery is non-removable, press the Wand Release button to detach the handheld vacuum. Plug the charger into the charging port on the handheld vacuum.

To put the vacuum in storage mode, press the MultiFLEX Wand Unlock Latch while folding the handheld vacuum forward until the wand clicks and locks. Plug the charger into the charging port on the handheld vacuum.

If battery is removable, press and hold the Battery Release Button, then slide out the battery. Plug the charger into the charging port on the battery. To reinstall the battery, slide it into the slot in the back of the handheld vacuum.

SETTINGS

Slide switch to the bottom to turn off power. To begin vacuuming in Standard Mode, slide switch to the desired setting.

Hard Floor/Small Area Rugs The brushrolls spin slowly to clean bare floors and small area rugs.

Carpet The brushrolls spin faster to pick up debris below the surface of your carpets.

For an added boost in power, pull the Trigger on the handheld vacuum. Release it to return to normal power.

CLEANING MODES

To clean floors, place foot on floor nozzle and tilt handheld vacuum back.NOTE: Brushrolls will only engage when the handheld vacuum is tilted back.

Press the wand release button and lift the handheld vacuum off the wand. Attach an accessory for great cleaning on stairs, furniture, and other above-floor areas.

Stand the vacuum upright and press the nozzle release button located at the bottom of the wand, above the nozzle. Lift wand to detach. Great for cleaning baseboards, ceiling fans, window sills, and other hard-to-access areas.

NOTE: All accessories are compatible with both the wand and the handheld vacuum.

USING THE MULTIFLEX® WAND

Press the unlock latch on the back of the wand, then adjust the angle.

Adjust the wand to a lower angle to easily clean under furniture.

MULTIFLEX STORAGE

To put the vacuum in storage mode, press the unlock latch while folding the handheld vacuum forward.

To take the vacuum out of storage mode, press the unlock latch and lift up the handheld vacuum until the wand clicks and locks into place.

MAINTAINING YOUR VACUUM

EMPTYING THE DUST CUP

Press the wand release button to detach the handheld vacuum from the wand.

To empty the Dust Cup while it is attached to the handheld vacuum, position the dust cup over a trash receptacle and slide the CleanTouch™ Dirt Ejector slider forward.

REMOVING AND CLEANING THE DUST CUP

To remove the dust cup from the handheld vacuum, press the CleanTouch™ Dust Cup Release button near the handheld vacuum nozzle. Tilt the dust cup and lift off to remove.To empty dust and debris, hold the dust cup over the trash, then slide the CleanTouch Dirt Ejector slider forward.

To clean the interior of the dust cup, rinse it with water. Place it on its side with the lid open to air-dry for at least 24 hours before reinstalling.

CLEANING THE FILTERS

Regularly rinse and replace the filters to maintain your vacuum’s suction power.To clean filters, rinse them with water only. Allow all filters to air-dry completely for at least 24 hours before reinstalling to prevent liquid from being drawn into electric parts.Clean the pre-motor filters at least once a month and post-motor or HEPA filter at least once a year. Tap off loose dirt between washes when needed. More frequent cleaning may sometimes be necessary with heavy use.

IMPORTANT: DO NOT use soap when cleaning the filters. Use water only.

Press the dust cup release button and remove the dust cup. Pull the foam and felt filters out of the back of the dust cup. Unit will not function if Post Motor filter is not in place.

Remove the dust cup. Pull the post-motor filter out of the handheld vacuum.

Pre-Motor Foam and Felt Filter Kit

Post-Motor HEPA Filter

FLOOR NOZZLE

If any hair is wrapped around the brushroll, continue cleaning using the Carpet setting on a bare floor surface, a low-pile carpet, or a small area rug. If some fibers remain wrapped around the brushroll after continued use, carefully remove them. If you run over a hard or sharp object, notice a noise change while vacuuming, or the nozzle indicator light turns red, check for blockages or objects caught in the self-cleaning brushroll or Soft Roller.

Turn off the vacuum.
Using a coin, turn locks counterclockwise to open, then lift off cover to access the self-cleaning brushroll.
Clear airway of blockages.
Replace cover by sliding inserts into slots, then pressing down firmly on all sides before turning locks clockwise to close, until they click securely into place.
If light on floor nozzle is red, see Troubleshooting section for resolution.

CLEANING SOFT ROLLER

To remove the Soft Roller from the nozzle, pull it out by the tab.
Tap loose debris off the Soft Roller. Use a dry towel to wipe the Soft Roller clean, and to remove any debris caught in the teeth behind the Soft Roller.
Hand wash the Soft Roller as needed. Use only water, and let air-dry completely for at least 24 hours.
Reinstall the Soft Roller in the nozzle.

CHECKING FOR BLOCKAGES

Checking for Blockages in the Handheld Vacuum:1. Turn off vacuum.2. Remove the handheld vacuum from the wand.3. Check all intake openings to the dust cup and remove any debris or blockage.

Checking for Blockages in the Wand:

Standard Wand:1. Turn off vacuum.2. Remove the handheld vacuum and floor nozzle.3. Check intake openings for blockages and debris.4. Clear away debris and blockages.MultiFLEX® Wand:1. Turn off vacuum.2. Remove the handheld vacuum and floor nozzle from the wand.3. Check the Clog Access Hose on the MultiFLEX section of the wand by pinching the tabs on both sides of the hose and lifting the hose out.4. Clear any debris and blockages.

Checking for Blockages in the Floor Nozzle:1. Turn off vacuum.2. Detach the wand.3. Use the edge of a coin to open the three locks on the bottom of the floor nozzle.4. Remove the cover and tilt back the neck of the floor nozzle.5. Check the opening and remove any debris.6. Replace the cover by sliding the inserts into the slots, then pressing down firmly on all sides before turning the locks clockwise to close, until they click securely into place.

TROUBLESHOOTING GUIDE

WARNING: To reduce the risk of shock and unintended operation, turn off power and remove the Lithium Ion Power Pack battery before servicing.Vacuum is not picking up debris. No suction or light suction. Nozzle light is red. (Refer to Checking for Blockages section for more information.)• Check filters to see if they need cleaning. Follow instructions for rinsing and completely air-drying the filters before reinserting in the vacuum.• Dust cup may be full; empty dust cup.• Check floor nozzle for blockages; clear blockages if required.• Remove any string, carpet fibers, or hair that may be wrapped around the brushrolls.• Check connection between handheld vacuum and wand for blockages; clear blockages if required. If the issue persists, please contact Customer Service.• Check clog access in wand for any blockages and clear any debris.Vacuum lifts area rugs. Vacuum is not turning on. Nozzle light is blinking red.• Make sure you are not engaging Boost mode. Take care when vacuuming area rugs or rugs with delicately sewn edges. The vacuum has overheated and turned off to cool down. Remove all blockages and wait 60 min to allow the motor to cool down.• Turn off the unit to disengage the brushrolls and restart with the power/selector switch.Brushrolls do not spin.• Immediately turn off the vacuum. Remove any blockages before turning the vacuum back on. Make sure the handheld vacuum is tilted back far enough for the brushrolls to engage. If the brushrolls still do not spin, please contact Customer Service.• If the floor nozzle has headlights and they are not illuminated, there is a connection issue between the handheld vacuum, wand, and nozzle. Try disconnecting and reattaching the pieces. If the headlights still do not illuminate, please contact Customer Service.Vacuum turns off on its own.There are several possible reasons for the vacuum turning off on its own, including blockages, battery issues, and overheating. If vacuum turns off on its own, perform the following steps:1. Turn on the vacuum and check the battery indicator lights located on the handheld vacuum. If recharging is needed, make sure the power/selector switch on the vacuum is set to the Off position before connecting the charger.2. Empty dust cup and clean filters (See Emptying the Dust Cup and Cleaning the Filters sections).3. Check wand, accessories, and inlet openings and remove any blockages.4. Allow unit and battery to cool for at least 45 minutes, until they return to room temperature.5. Restart with power/selector switch.NOTE: If vacuum still does not operate properly, contact Customer Service at 1-800-798-7398.Battery Indicator Lights on handheld vacuum are flashing.• Bottom LED light is flashing (Fig. A): Battery needs to be charged.• Top and bottom LED lights are flashing (Fig. B): Battery temperature is not optimal, so charging is temporarily paused. Leave battery plugged in and charging will resume soon.• If top 2 or bottom 2 LED lights are flashing (Fig. C, Fig. D), call Customer Service at 1-800-798-7398.

ADDITIONAL ACCESSORIES AVAILABLE ON SHARKACCESSORIES.COM

A 8″ Crevice ToolB 18″ Flexi Crevice ToolC Duster Crevice ToolD Dusting BrushE Multi-Angle Dusting BrushF Anti-Allergen Dust BrushG Upholstery ToolH Wide Upholstery ToolI Pet Multi-ToolJ Deep-Cleaning Motorized Pet ToolK MultiFLEX® Under-Appliance WandL Accessory BagM Li-Ion ChargerN Dual Li-Ion ChargerO Li-Ion Battery

NOTE: Not all accessories come with all units. For a list of the accessories included with this model, see the top inside flap of the box. To order additional accessories, visit sharkaccessories.com.

FIVE (5) YEAR LIMITED WARRANTY

The Five (5) Year Limited Warranty applies to purchases made from authorized retailers of SharkNinja Operating LLC. Warranty coverage applies to the original owner and to the original product only and is not transferable. SharkNinja warrants that the unit shall be free from defects in material and workmanship for a period of five (5) years from the date of purchase when it is used under normal household conditions and maintained according to the requirements outlined in the Owner’s Guide, subject to the following conditions and exclusions:What is covered by this warranty?1. The original unit and/or non-wearable components deemed defective, in SharkNinja’s sole discretion, will be repaired or replaced up to five (5) years from the original purchase date.2. In the event a replacement unit is issued, the warranty coverage ends six (6) months following the receipt date of the replacement unit or the remainder of the existing warranty, whichever is later. SharkNinja reserves the right to replace the unit with one of equal or greater value.What is not covered by this warranty?1. Normal wear and tear of wearable parts (such as foam filters, HEPA filters, pads, etc.), which require regular maintenance and/or replacement to ensure the proper functioning of your unit, are not covered by this warranty. Replacement parts are available for purchase at sharkaccessories.com.2. Any unit that has been tampered with or used for commercial purposes.3. Damage caused by misuse (e.g., vacuuming up water or other liquids), abuse, negligent handling, failure to perform required maintenance (e.g., not cleaning the filters), or damage due to mishandling in transit.4. Consequential and incidental damages.5. Defects caused by repair persons not authorized by SharkNinja. These defects include damages caused in the process of shipping, altering, or repairing the SharkNinja product (or any of its parts) when the repair is performed by a repair person not authorized by SharkNinja.6. Products purchased, used, or operated outside North America.How to get serviceIf your appliance fails to operate properly while in use under normal household conditions within the warranty period, visit sharkclean.com/support for product care and maintenance self-help. Our Customer Service Specialists are also available at 1-800-798-7398 to assist with product support and warranty service options, including the possibility of upgrading to our VIP warranty service options for select product categories. We also ask that you register your product online at registeryourshark.com and have the product on hand when you call, so we may better assist you. SharkNinja will cover the cost for the customer to send in the unit to us for repair or replacement. A fee of $25.95 (subject to change) will be charged when SharkNinja ships the repaired or replacement unit.How to initiate a warranty claimYou must call 1-800-798-7398 to initiate a warranty claim. In order to better assist you please register your product prior to calling and have your product with you at the time of your call. You will need the receipt as proof of purchase. A Customer Service Specialist will provide you with return and packing instruction information. We also ask that you register your product online at registeryourshark.com and have the product on hand when you call, so we may better assist you.How state law appliesThis warranty gives you specific legal rights, and you also may have other rights that vary from state to state. Some states do not permit the exclusion or limitation of incidental or consequential damages, so the above may not apply to you.

TWO (2) YEAR LIMITED BATTERY WARRANTY

The Two (2) Year VIP Limited Warranty applies to purchases made from authorized retailers of SharkNinja Operating LLC. Warranty coverage applies to the original owner and to the original product only and is not transferable. SharkNinja warrants that the battery shall be free from defects in material and workmanship for a period of two (2) years from the date of purchase when it is used under normal household conditions and maintained according to the requirements outlined in the Owner’s Guide, subject to the following conditions and exclusions:What is covered by this warranty?1. The original battery deemed defective, in SharkNinja’s sole discretion, will be replaced up to two (2) years from the original purchase date.2. In the event a replacement battery is issued, the warranty coverage ends six (6) months following the receipt date of the replacement battery or the remainder of the existing warranty, whichever is later. SharkNinja reserves the right to replace the unit with one of equal or greater value.What is not covered by this warranty?1. Normal wear and tear of the battery, which requires optimal temperature storage and operation to ensure its proper functioning. Replacement batteries are available for purchase at sharkclean.com/batteries.2. A battery that has been tampered with or used for commercial purposes.3. Damage caused by misuse (e.g., exposing battery to liquids or extreme hot and/or cold temperatures), abuse, negligent handling, failure to perform required maintenance, or damage due to mishandling in transit.4. Consequential and incidental damages.5. Defects caused by repair persons not authorized by SharkNinja. These defects include damages caused in the process of shipping, altering, or repairing the SharkNinja product (or any of its parts) when the repair is performed by a repair person not authorized by SharkNinja.6. Products purchased, used, or operated outside North America.How to get serviceIf your battery fails to operate properly while in use under normal household conditions within the warranty period, visit sharkclean.com/support for product care and maintenance self-help. Our Customer Service Specialists are also available at 1-800-798-7398 to assist with product support and warranty service options. So we may better assist you, please register your product online at registeryourshark.com and have the product on hand when you call. SharkNinja will cover the cost for the customer to send in the unit to us for replacement. A fee of $19.95 (subject to change) will be charged when SharkNinja ships the replacement unit.How to initiate a warranty claimYou must call 1-800-798-7398 to initiate a warranty claim. You will need the receipt as proof of purchase. We also ask that you register your product online at registeryourshark.com and have the product on hand when you call, so we may better assist you. A Customer Service Specialist will provide you with return and packing instruction information when you call.How state law appliesThis warranty gives you specific legal rights, and you also may have other rights that vary from state to state. Some states do not permit the exclusion or limitation of incidental or consequential damages, so the above may not apply to you.

NOTES ____________

http://registeryourshark.com

RECORD THIS INFORMATIONModel Number: __________________________________Date Code: ______________________________________Date of Purchase: _________________________________(Keep receipt)Store of Purchase: _________________________________TIP: You can find the model and serial numbers on the QR code label on the bottom of the back of the handheld vacuum and battery.

TECHNICAL SPECIFICATIONSVoltage: 25.2V DCPower: 281W

PLEASE READ CAREFULLY AND KEEP FOR FUTURE REFERENCE.This Owner’s Guide is designed to help you keep your vacuum running at peak performance.BATTERY REMOVAL AND DISPOSALThis product uses a lithium-ion rechargeable and recyclable battery. When the battery no longer holds a charge, it should be removed from the vacuum and recycled. DO NOT incinerate or compost the battery. When your lithium-ion battery needs to be replaced, dispose of it or recycle it in accordance with local ordinances or regulations. In some areas, it is illegal to place spent lithium-ion batteries in the trash or in a municipal solid waste stream. Return spent battery to an authorized recycling center or to retailer for recycling. Contact your local recycling center for information on where to drop off the spent battery.

PLEASE READ CAREFULLY AND KEEP FOR FUTURE REFERENCE.This Owner’s Guide is designed to help you get a complete understanding of your newShark® vacuum.SharkNinja Operating LLCUS: Needham, MA 02494CAN: Ville St-Laurent, QC H4S 1A71-800-798-7398sharkclean.comIllustrations may differ from actual product. We are constantly striving to improve our products; therefore the specifications contained herein are subject to change without notice.For SharkNinja U.S. Patent information, visit sharkninja.com/uspatents© 2021 SharkNinja Operating LLC. DUOCLEAN, MULTIFLEX, and SHARK are registered trademarks of SharkNinja Operating LLC. CLEANTOUCH, POWERFINS, and VERTEX are trademarks of SharkNinja Operating LLC.

IZ400Series_IB_REV_Mv6PRINTED IN CHINA

@sharkcleaning

References

[xyz-ips snippet=”download-snippet”]

Posted

2023-01-14

Shark VERTEX

admin

Tags:

IZ440, IZ460, IZ480, MultiFLEX DuoClean Vacuum, PowerFins Cordless Vacuum, Shark VERTEX, Vacuum with Self-Cleaning Brush roll