Smart Video DoorBell Instruction Manual

Smart Video Door Bell Instruction Manual

Smart Video Door Bell Instruction Manual

• Thanks for purchasing and using our product. Please read this quick start guide before using, and keep it for future reference.
• Menu contents are subject to change without notice in accordance with our policy of continuous product improvement.

What’s In The Box

Please consult below checklist for all the components.

Video DoorbellUSB CableUser GuideScrews & ToolsBatteriesDouble-sided Tape

Meet The Doorbell

1. 2MP Camera
2. PIR Motion Sensor
3. Speakers
4. Status Indicator
5. Doorbell Button
6. Microphone
7. Charging Indicator
8. Micro USB Port
9. Reset Hole
10. Hardwire Power Port
11. SD Card Slot
12. Battery Compartment

Battery Installation

The batteries are pre-installed into the doorbell. If you had taken out the batties somehow, please note the electrodes when installing batteries. Do put the positive poles upward!

Note:Improper battery installation will cause damage to the internal components and may result in serious injury.

Battery Charging

The batteries inside the video doorbell are not fully charged in accordance with transportation safety regulations.Please charge the batteries with an USB compatible wall charger(not included in the box) and the provided USB cable for about 8~10 hours prior to Wi-Fi set up and installation.

App Download

Download and install the ‘CloudEdge’ app from Google PlayTM or the App StoreTM.The app is also available by scanning below QR codes, using your QR code scanner in your smart phone.

CloudEdgeiOSAndroid

Note:AndroidTM is a trademark of Google Inc. Google PlayTM is a trademark of Google Inc. Apple, iPhone and iOS are trademarks of Apple Inc.App StoreTM is a service mark of Apple Inc.

WiFi Set Up

Before you start the Wi-Fi configuration, please note below:

1. The doorbell works with 2.4 GHz Wi-Fi, but not with 5 GHz Wi-Fi.
2. Avoid using special characters or punctuation symbols (@~!#$%^&*…) either in your Wi-Fi name or in the password.
3. Perform the configuration near your Wi-Fi router.

Launch the CloudEdge APP and register an account with your mobile phone numer of email ID. Then tap the ‘+’ button to add a new device, select doorbell and follow the in-app instructions to set up your doorbell.

Run A Test

After setup, tap on the live view window in the app for a test.Then take your doorbell outside to the installation spot and run a test there. Make sure the installation spot is covered by strong 2.4 GHz Wi-Fi signal.Note:If the video quality from the doorbell outside is not as good as it was indoors, you may need to move your router closer to your installation spot, or invest in an Wi-Fi extender.

Live View Interface

1. Quit live viewing
2. Setting menu
3. Battery status
4. Volume on/off
5. HD/SD switch
6. Full screen view
7. Stream bit rate
8. Wi-Fi signal status
9. Screenshot button
10. Speak to the scene
11. Record on smart phone
12. Body detection on/off
13. Notification history
14. Cloud storage service

Leave A Voice Message

You can leave a maximum 30-second voice message on the on-board memory of your doorbell, so as to quickly respond your visitor by a tap on your phone when you are out and occupied. It can be done even without an Micro-SD card.

Steps:Setting -> Host Leaves Message -> Record your message -> Hang off doorbell call and play the pre-recorded voice message.

Installation

Select location

Your doorbell has 140-degree view angle and 120-degree human detection range.

It is suggested to mount your doorbell at least 5 feet (160 cm) above the ground for the best angle of view and motion detection performance.

Mount Your Doorbell

1. Take out the wall mount by pushing from its back.
2. Mark the screw positions to mount the bracket.
3. Drive the screws into the anchors, or directly into your wall until the bracket is tightly fastened on your wall.
4. (Optional) You can also use the double-sided tape that we provided instead of screws.
5. Attach your doorbell to the mounting bracket. Make sure it reaches the bottom where you can hear a click.
6. Secure your doorbell with the provided star-shaped security screw and screwdriver.All set. Congratulations!

Key Features

Remote view & controlThe device will be in sleep mode to save power, and can be activated remotely  from your CloudEdge app to view and control.

Full-duplex audioThe device support 2-way audio intercom. You can see, hear and speak to your visitor even when you are not home

Pre-recorded quick responseA 30 second voice message can be pre-recorded into the doorbell, which enables you to quickly respond your visitor with a tap on your phone, even when you are out and occupied.

PIR human detectionWith PIR motion sensor built-in, you doorbell detects human movements in front of it and sends you motion alerts and snapshots prior to the visitor’s knock. And it prevents intrusion/burglatry before they actually happen.

Low battery alertEmbedded with power management module, you doorbell can tell you the battery consumption status, showing the estimated usage time and sending you low-battery alerts when it needs a recharge.

Local & cloud recordingInsert a Micro-SD card (Max.support 128GB) or activate the clouds storage service to record your video clips.

Day & nightThe video doorbell support night vision. To see clearly what’s going on in front of door anytime, anywhere.

Specification

Video & Audio
Image Sensor	1/2.7” CMOS (2.0MP)
OS	Hisilicon Lite-OS
Effective Pixels	1920 × 1080 px
Stream	HD/SD dual stream
Infrared LED	High power IR LED with ICR
Lens	1.7mm/F2.0
Angle of View	140°
Min. Illuminance	Color: 0.01 Lux; B&W: 0.001Lux
WDR	Digital WDR
Audio	Two-way audio with noise cancellation
Storage
Storage Type	Micro SD Card (Max 128G)
Cloud storage	Support
Recording	Triggered by PIR motion sensor
Network
Wifi Frequency	2.4 GHz ~ 2.4835 GHz
Standards	IEEE 802.11 b/g/n
Live View Speed	within 3 ~ 4 Sec
APP
App Name	CloudEdge
OS	iOS, Android
Remote View	Within 2~4 sec
Notification	Notification push within 2~4 sec
Others
Working Temp. & Humidity	-20℃ ~ 50℃;
Power Source	Lithium 18650 Battery (3.5V, 3000mAh ) × 2
Standby Current	300μA
Working Current	250mA
Standby Time	4 ~ 6 Months
Working Time	2 ~ 3 Months (20 times wake up per day)
Battery Charging	DC5V 1A~2A Power Adapter (Micro USB Port)
Firmware Upgrade	OTA (on the air)
Size (mm)	61× 41 × 135
Weight (g)	235

FAQS

Why I failed to set up Wi-Fi for the doorbell?

Device works with 2.4GHz Wi-Fi only, but not support 5GHz Wi-Fi.Wi-Fi network is not good, try to keep the camera near the Wi-Fi router when setting up.The Wi-Fi password is wrong.Please check if there are special characters in the password, or the network is specially encrypted.

How do I know if I have 2.4G or 5G wifi?

Please check the user manual of your Router or call the network operator for help.

It has to be on same WiFi to see the camera, or is it over internet from anywhere?

You can view the camera from anywhere, if your camera is well connected to the internet.

Do any of the recordings get saved to the cloud? Or is it mainly saved in the built-in SD card?

It supports SD card recording as well as cloud storage. You can activate the cloud storage service in App.

What happens when the SD is full?

When the memory card is full, the camera automatically erase the oldest footage.

Does it work with Google Home or Alexa?

Sorry, this model does not support Google Home or Alexa.

Why does it lose connection to wifi?

Please check the network connection of your phone and the Wi-Fi router. If the network signal is not strong, you may need to move your router closer to the device, or invest in an extender.

Can the motion detection be disabled?

Yes, sure. Recording is triggered by detected motions. You can set up the sensitivity or disable motion detection in the setting menu.

Do we get charger for the batteries?

Battery charger is not included. Please charge the batteries with a USB compatible charger(DC5V 1A~2A) for about 8-10 hours.

Can we have 2 or more doorbells at the same residence?

Yes, you can add more than one device at the same residence.