Soundcore Life NoteUser Manual
Charging
- Remove the protective film from the earbuds when using for the first time.
- Fully charge both the earbuds and the charging case before the first use.
- To prevent damage, use the provided USB-C cable.
- Fully dry off the earbuds and the USB port before charging.
LED indicator (Earbuds & Charging case)
Powering On/Off
The earbuds will automatically power on when taken out of the charging case and power off when placed back into the charging case.
LED indicator (Earbuds)
- To manually power on, press the multi-function button on either one of the earbuds.
- To manually power off, press and hold the multi-function button on either one of the earbuds for 3 seconds.
Pairing
True Wireless Stereo Connection
The right earbud will automatically connect with the left earbud when taken out of the charging case.
LED indicator (Earbuds)
- When powered off, press and hold the multi-function button on both earbuds for 1 second, the earbuds will enter TWS connecting mode.
- When powered on and connected, place either one of the earbuds into the charging case, you can keep using the other one.
- When powered on and connected, if either one of the earbuds is out of battery and powered off, you can keep using the other one.
- When you are on a call, place either one of the earbuds into the charging case, 3 to 5 seconds later, the microphone in the other earbud will be activated.
Bluetooth Pairing with your Device
The earbuds will enter pairing mode when powered on. You are requested to confirm the connection when you see a pop-up.
LED indicator (Earbuds)
In the pairing process, some devices are incompatible with Qualcomm True Wireless Primary- Secondary dual pairing names, it may notice “connection unsuccessful” when you tap “Pair” or even no screen pops up. Don’t worry and it will not influence the using.
Once successfully paired, the primary earbud connects with your device and transfers signal to the secondary earbud, the latter one will not connect with your device. As a result, in the Bluetooth pairing list on your device, it may indicate that only one side is connected while the other side is not.
- To pair with another Bluetooth device, turn off Bluetooth on the currently connected device first.
- Each time you power on your Soundcore earphones, it will automatically connect to your last successfully connected device if available within the Bluetooth range.
Wearing
- Choose the EarTips that fit your ears best.
- Insert the earbuds into the inner canal of your ears.
- Turn and find the most comfortable position.
Controls
Reset
Reset the earbuds if the earbuds cannot connect properly with each other or with your device.
- Place the earbuds into the charging case and make sure they are being charged.
- Press and hold the button on both earbuds for 3 seconds until the LED indicators flash red 3times and then turn white.
⇒ All the memory data will be cleared.
Specifications
Specifications are subject to change without notice.
- Input : 5 V 750 mA
- Rated output power : 7 mW @ 1% THD
- Battery capacity : 55 mA x 2 (earbuds); 810 mA (charging case)
- Charging time : 2 hours
- Playtime (varies by volume level and content) : 7 hours (Totally 40 hours with the charging case)
- Driver size : 6 mm × 2
- Frequency response : 20 Hz – 20 kHz
- Impedance : 16 Ω
- Bluetooth version : V 5.0
- Bluetooth range : 10 m / 33 ft
Qualcomm® aptXTM Technical specificationsCompression ratio: 4:1Word depth: Support 16bit and 24bitDecoding delay: Sample rate 48kHz<2msDynamic range: 16bit>92dB, 24bit>120dBData rates: 352kbpsDecode mode: Stereo
Qualcomm aptX is a product of Qualcomm Technologies, Inc. and/or its subsidiaries.Qualcomm is a trademark of Qualcomm Incorporated, registered in the United States and other countries. aptX is a trademark of Qualcomm Technologies International, Ltd., registered in the United States and other countries.
[xyz-ips snippet=”download-snippet”]