STAIRVILLE Strobe-Master I User Guide

Table of Contents

Strobe-Master I

Quick Start Guide

This quick start guide contains important information on the safe operation of the product. Read and follow the safety advice and instructions given. Retain the manual for future reference. If you pass the product on to others please include this manual.

Safety instructions

Intended useThis device is intended to be used to control electronic strobe effects devices. Any other use or use under other operating conditions is considered to be improper and may result in personal injury or property damage. No liability will be assumed for damages resultingfrom improper use.Danger for childrenEnsure that plastic bags, packaging, etc. are disposed of properly and are not within reach of babies and young children. Choking hazard! Ensure that children do not detach any small parts from the product. They could swallow the pieces and choke! Never let children unattended use electrical devices.Eye damage caused by high light intensityTo avoid eye damage caused by high light intensity, never look directly into the light source.

Where to use the productNever use the product

in conditions of extreme temperature or humidity
in extremely dusty or dirty areas
at locations where the unit can become wet

General handling

To prevent damage, never use force when handling the product.
Never immerse the product in water. Just wipe it with a clean dry cloth. Do not use liquid cleaners such as benzene, thinners, or flammable cleaning agents.

Features

For all DMX and analog strobes
The controller provides 10 programs, Blackout, Single flash, Full on
Speed and brightness controllable via faders
Power supply unit included

Operating

BLACKOUT – Blackouts the strobes (standby)
FULL-ON – All strobes light up at once
SINGLE FLASH – All strobes will flash each time you press this button in BLACKOUT mode
DIMMER – To adjust the brightness of DMX strobes in a range of 20 % to 100 %
SPEED – To adjust the chase speed in AUTO mode
MODE – Yellow LED indicates = AUTO mode Green LED indicates = Sound-to-Light mode
CHASE – Press the buttons to select 10 chase patterns:0 = random patterns1 = 1234 (100 % brightness)2 = 1 → 2 → 3 →4 →→4 →3 →2 →13 = 1 → 2 →3 → 4 → 3 → 2 → 14 = 12 → 34 →→ 24 → 13 →→ 23 → 145 = 1 → 12 → 123 → 1234 → 123 → 12 → 1 → stop →→ 4 → 43 → 432 → 4321 → 432 → 43 → 4 → stop6 = 1 → 12 → 123 → 1234 → 234 → 34 → 4 → stop →→ 4 → 43 → 432 → 4321 → 321 → 21 → 1 → stop7 = 1 → 3 → 2 → 4 → 3 →1 → 4 → 28 = 12 → 23 → 34 → 41 →→ 43 → 43 → 21 → 149 = 12 → 123 → 12 →1234
POWER – Mains switch to turn the unit on / off
DC Input – Connect the supplied mains power adaptor hereCH1 – CH4 – Outputs for analog strobes: Signal: +12 V; 1/4” phone jack (mono)DMX STROBE – DMX512 output for DMX strobes: Channel 1: strobe rate, Channel 2: Brightness

Technical specifications

• Dimensions (W × H × D):	210 mm × 133 mm × 77 mm
• Weight:	0.8 kg
• Operating voltage:	9 V / 500 mA

For the transport and protective packaging, environmentally friendly materials have been chosen that can be supplied to normal recycling. Ensure that plastic bags, packaging, etc. are properly disposed of. Do not just dispose of these materials with your normal household waste, but make sure that they are collected for recycling. Please follow the notes and markings on the packaging.

This product is subject to the European Waste Electrical and Electronic Equipment Directive (WEEE) in its currently valid version. Do not dispose of your old device with your normal household waste. Dispose of this product through an approved waste disposal firm or through your local waste facility. Comply with the rules and regulations that apply in your country. If in doubt, consult your local waste disposal facility.