SUN ORIGIN Expresso Machine 15bar, 1450W User Manual

SUN ORIGIN Expresso Machine 15bar, 1450W User Manual

PLEASE READ AND SAVE THESE IMPORTANT SAFETY INSTRUCTIONS.

Read the operating instructions carefully before putting the appliance into operation and keep the instructions, the receipt and, if possible, the box with the internal packing. If you give this appliance to other people, please also pass on the operating instructions.

USER MANUAL SYMBOLS

Important information for your safety is specially marked. It is essential to comply with these instructions in order to avoid accidents and prevent damage to the machine:

WARNING: This sign warns you of dangers to your health and indicates possible injury risks. CAUTION: This sign refers to possible hazards to the machine or other objects.NOTE: This sign highlights tips and information

IMPORTANT SAFEGUARDS

  1. Ensure that the voltage indicated on the appliance rating label corresponds to the voltage in the mains.
  2. The appliance is designed exclusively for private, domestic use and for the envisaged purpose. This appliance is not suitable for commercial use.
  3. This appliance is intended for making espresso coffee, cappuccino and hot water supply.
  4. Do not use the appliance outdoors.
  5. Always plug the appliance into an outlet that is earthed. Risk of electric shock!
  6. Appliance is not intended to operate with an external timer or a separate remote-control system.
  7. Keep the appliance away from heat sources, direct sunlight, moisture (do not immerse it in any liquid) and sharp edges.
  8. Do not use the appliance with wet hands. If the appliance gets wet, disconnect it immediately from the power supply.
  9. To protect against risk of electric shock, do not immerse the cord, plug or unit in water or any other liquid.
  10. Place the appliance on a flat surface. Do not place the appliance on or near an electric burner, heated oven or gas stove (keep a minimum distance of at least 60 cm).
  11. Keep a minimum distance of at least 60cm from the tap.
  12. not move the appliance during operation.
  13. Do not cover the appliance during operation.
  14. Do not place the appliance in or under wall cabinets during operation.
  15. Before cleaning, storing and adding / removing components, switch off the appliance and unplug it.
  16. Do not operate the appliance without supervision. If you should leave the workplace, always unplug the appliance.
  17. CAUTION: Take special care when using the appliance in places where there are children, the disabled or people with reduced physical, sensory ormental abilities.
  18. The appliance can be used by people with reduced physical, sensory or mental abilities or lack of experience and knowledge, if they are supervised orinstructed on how to use the device safely and understand the risks involved.
  19. This appliance may be used by children aged 8 years and over if they have been supervised or instructed in the safe use of the appliance and are aware of the risks involved. Cleaning and maintenance is prohibited for children unless they are older than 8 years and are supervised.
  20. Keep the appliance and its cord out of the reach of children.
  21. Do not let children play with the appliance.
  22. In order to ensure your children’s safety, please keep all packaging (plastic bags, boxes, polystyrene etc.) out of their reach.WARNING: Do not allow children to play with the foil. Danger of suffocation!
  23. Children are not allowed to use the appliance.
  24. Unplug when not in use and before cleaning.
  25. Do not attempt to repair the appliance by yourself. Contact a qualified technician.
  26. Periodically check the cable for damage.WARNING: Do not operate the appliance with a damaged cord. In order to avoid the risk of an electric shock, never try to repair the appliance by yourself.Bring it to the authorized service station for repair. Use only the original spare parts. CAUTION: Risk of electric shock or fire!Do not disassemble the appliance.Do not use additives or other components not supplied by the manufacturer.
  27. Do not let the power cord hanging off the edge of a table or bench, or come into contact with hot surfaces.
  28. If the surface is cracked, disconnect the appliance from the power supply to avoid electric shock.
  29. CAUTION: The outer surface of the appliance may develop high temperatures during operation. Do not touch the outside of the device during use. Allow the appliance to cool down before storage.
  30. Group head, filter holder, steam nozzle and cup tray get very hot during operation.
  31. Hold the group by the handle only.
  32. Do not touch group head, steam nozzle and cup tray! Let these parts cool down before cleaning.
  33. Do not point the steam jet towards yourself or other persons. Place a container under the steam nozzle, so that water/steam residues will be drained.WARNING: Ensure that no humidity enters the casing. Risk of electric shock.
  34. CAUTION: Fill the water tank only with fresh, potable water. Do not use carbonated water (sparkling mineral water).
  35. Ensure that the filter holder is secure and properly locked during operation, since this appliance works under pressure.
  36. Do not operate the appliance without any water inside the tank and do not overfill it. The water level must always be between the MIN and MAX points.

PARTS IDENTIFICATION

  1. Detachable drip tray with grid
  2. Detachable steam nozzle
  3. Detachable water tank
  4. Rotary switch (select power)
  5. Detachable water tank lid
  6. Stainless steel heated surface
  7. Single dose coffee selection button
  8. On / Off button
  9. Double coffee selection button
  10. Group

DESCRIPTION OF CONTROL PANEL AND ROTARY SWITCH

BEFORE FIRST USE

  1. Read all instructions carefully and keep them for future reference.
  2. Remove all packing materials and keep them away from children.
  3. After unpacking the appliance, check for possible damage. In the event of a fault or visible problem, do not use the device and contact the store where you purchased it.
  4. It is recommended that you clean the appliance as described in the “Cleaning” section.
  5. Ensure that the voltage indicated on the appliance rating label corresponds to the voltage in the mains.
  6. Make sure that the appliance only plugs into a properly grounded and properly installed socket.
  7. Place the appliance on a flat surface and away from flammable objects. Always keep out of the reach of children.
  8. Bleed the appliance before the first use and after a long time of not using it. Do not use coffee during this process!
  9. Make sure the drip tray and grill are properly positioned.
  10. Set the rotary switch dial to “Coffee” position

  11. Position the group. Hold the handle of the group, and place the guides in the corresponding recesses of the espresso machine. Pull the group to the right of the espresso machine with the handle, until the handle is at the same point as “LOCK”. Make sure the group secures into place.
  12. Remove the water tank lid by squeezing both ends of the lid and pulling slightly upwards.WARNING: Do not push or pull the lid too hard.
  13. Fill the water tank with clean, potable water up to the MAX mark (maximum water temperature should not exceed 35°C). Close the lid.
  14. Connect the appliance to the power supply.
  15. Press the power switch to turn on the appliance.
  16. Turn the steam nozzle out.
  17. Place a heat-resistant container/ at least 100 ml under the steam nozzle.
  18. Set the rotary switch to the “Hot water” position.
  19. The hot water indicator light flashes quickly and the appliance enters the hot water supply mode.
  20. The steam nozzle will start producing hot water until it produces 100ml. The nozzle can produce hot water for 120 seconds continuously.CAUTION: The water running from the supply is hot. Risk of burns!
  21. Turn off the hot water supply by setting the power selector to the ‘Coffee’ position. In case you want to repeat the process, turn the switch to the hot water supply mode (steps 18/19/20/21)
  22. Place a heat-resistant container/ at least 100 ml on the grill and under the group. Make sure the water tank has at least 150ml of water.
  23. Press the single or double dose coffee maker. The corresponding indicator light will start flashing. When the light stops flashing, water will start running from the group outlets.CAUTION: Do not drink or use this water for any reason!
  24. Press the power switch.
  25. The appliance is now ready for operation.TIP: Repeat the procedure 2-3 times for good cleaning of the device before the first use.

HOW TO USE

  1. Ensure that the voltage indicated on the appliance rating label corresponds to the voltage in the mains.
  2. Make sure that the appliance only plugs into a properly grounded and properly installed socket.
  3. Place the appliance on a flat surface and away from flammable objects. Always keep out of the reach of children.
  4. The appliance has the following functions:

MAKING ESPRESSO

  1. Set the rotary switch to the “Coffee” position.
  2. Make sure that the drip tray and its grid are in the correct position.
  3. Remove the water tank lid by squeezing both ends of the lid and pulling slightly upwards.WARNING: Do not push or pull the lid too hard
  4. Fill the water tank with clean, potable water up to the MAX mark (maximum water temperature should not exceed 35°C). Close the lid.
  5. Select a filter for single or double dose and place it inside the group.
  6. Fill the filter with coffee using the included dispenser. Spread and squeeze the coffee evenly using the tamper.Clean the edges of the filter of any coffee residue.
  7. Place the group in the espresso machine. Hold the handle of the group, and place the guides in the corresponding recesses of the espresso machine. Pull the group to the right of the espresso machine with the handle, until the handle is at the same point as “LOCK”. Make sure the group secures into place.

  8. Place a heat-resistant container on the grid and under the group. Make sure the water tank has at least 150ml of water.
  9. Press the single or double dose coffee maker button. The corresponding indicator light will start flashing (warm-up). When the light stops flashing, coffee will start flowing out of the group outputs.
  10. Once the process is complete, press the power button and remove the device from the power supply.
  11. Allow the appliance to cool down well before cleaning it (see section “CLEANING”).

Follow the steps below to make frothed milk. The frothed milk should be firm enough, creamy, with a viscous texture so that it can be formed with a spoon.

For its preparation you need in addition the following materials:

  • a cup (approx. 180ml), in which you make the espresso
  • a frothing jug with spout (approx. 300ml)
  • a heat-resistant container
  • cold milk at least 3.5% fat content

ATTENTION: Pay attention to the following series!

  1. Make espresso, as described in the section “MAKING ESPRESSO”.
  2. Make frothed milk following the instructions below:WARNING: Steam can cause injuries. During the heating process hot steam / water may escape from the group and/ or the steam nozzle! Risk of burns!
  • Do not point the steam nozzle at your face.
  • Always place a container under the steam nozzle.
  1. Before activating the steam function, make sure that the rotary switch is in the “Coffee” position.
  2. Turn the steam nozzle out. Install the cover on the steam nozzle.
  3. Fill the jug with 50ml cold milk.
  4. Place the jug of milk under the steam nozzle.
  5. Raise the jug so that the tip of the steam nozzle is just below the surface of the milk.NOTE: Do not place the steam nozzle in the center of the jug, but near the side inner wall. This position allows the milk to enter a proper circular motion. We suggest that you hold the nozzle in a fixed place on the inner wall and turn the jug in a circular motion.
  6. Set the rotary switch to the “Steam” position.
  7. The steam generating indicator light will start flashing quickly and the appliance will enter the steam mode.At first it may take some time to warm up the device. Once the appliance is ready, the appliance will startproducing steam.
  8. Shake the jug slightly up and down. Turn the rotary switch to the “Coffee” position when the milk reaches the desired volume (approx. 50%).NOTE: For extra heating of the milk, place the steam nozzle towards the bottom of the jug. Make sure the milk does not start to boil. In this case, the frothed milk will dissolve.
  9. To remove the last coarse air bubbles knock the froth jug after frothing carefully on the tabletop. Swivel the milk jug slightly around. This helps to mix the foam after frothing. Pour the frothed milk slowly into the espresso.
  10. Swivel the milk jug slightly around while pouring the frothed milk slowly into the espresso.NOTE: With a few artful movements you can draw designs onto the foam. Sprinkle cocoa powder or cinnamon for extra yummy taste.
  11. IMPORTANT: Clean the steam nozzle immediately after every use! When switch the steam control knob off there is vacuum creating, which insert milk into the steam nozzle. Place your heat-resistant container under the steam nozzle. Open the steam control knob briefly for a shot of steam to flush milk residue out of the steam nozzle. Wipe the steam nozzle with a damp cloth.
  12. Turn off the steam function by setting the switch to the position “Coffee”.
  13. Press the power button on the appliance and disconnect it from the power supply.NOTE: After steaming, the appliance is in a state of high temperature and pressure. To ensure the best taste of your coffee, do not start the coffee operation immediately.

USE OF ESPRESSO POD

The package includes a special filter for espresso pods, so you can enjoy the coffee of your choice with ease. Before proceeding, make sure that the rotary switch is in the “Coffee” position. Place the pod filter in the group, then place the espresso pod in the group and follow steps 7 to 11 of the “MAKING ESPRESSO” section.

HOT WATER PRODUCTION

  1. Make sure the drain pan and grill are properly positioned.
  2. Set the function selector dial to “Coffee”.
  3. Install the group. Hold the handle of the group, and place the guides in the corresponding recesses of the espresso machine. Pull the group to the right of the espresso machine with the handle, until the handle is at the same point as “LOCK”. Make sure the group secures into place.
  4. Remove the water tank lid by squeezing both ends of the lid and pulling slightly upwards.WARNING: Do not push or pull the lid too hard
  5. Fill the water tank with clean, potable water up to the MAX mark (maximum water temperature should not exceed 35 ° C). Close the lid.
  6. Connect the device to the power supply.
  7. Press the power switch to turn on the device.
  8. Turn the steam nozzle out.
  9. Place a heat-resistant container/ at least 100 ml under the steam nozzle.
  10. Set the rotary switch to the “Hot water” position
  11. The hot water indicator light flashes quickly and the appliance will enter the hot water supply mode.
  12. The steam nozzle will start producing hot water. The nozzle can produce hot water for 120 secondscontinuously.

CAUTION: The water running from the supply is hot. Risk of burns! Turn off the hot water supply by setting the power selector switch to the ‘Coffee’ position. If you want extra hot water, turn the rotary switch to the “Hot water” position again.

ENERGY SAVING FUNCTION

The appliance enters the power save mode after 15 minutes of inactivity and all power indicators light up.

Press any key to exit the power save mode.You can put the device in/ out of the power save mode manually in the following two ways: Press and hold the single and double coffee keys simultaneously, connect the appliance to the power supply and the appliance activation indicator light will illuminate.

  • Press the single dose coffee key and the corresponding indicator light will go out. The device will exit power saving mode.
  • Press the double dose coffee key and the corresponding indicator light will illuminate. The device will enter power saving mode.

DESALINATION

Salts endanger the operation of your appliance. Frequent desalination of the device is necessary. The frequency of desalination depends on the frequency of use and the hardness of the water (at least after the production of 400 doses of coffee).

  1. Insert the group. Hold the handle of the group, and place the guides in the corresponding recesses of the espresso machine. Pull the group to the right of the espresso machine with the handle, until the handle is at the same point as “LOCK”. Make sure the group is securely in place.
  2. Remove the water tank lid by pressing the two ends of the lid and pulling slightly upwards.WARNING: Do not push or pull the lid too hard.
  3. Use a commercial desalination fluid for espresso machines. Refer to the instructions for use of the descaling fluid for proper dosing. Close the lid.
  4. Place a heat-resistant container on the grill and under the group.
  5. Press and hold the single dose coffee maker and connect the appliance to the power supply.
  6. When the activation and single-dose coffee indicators light up, press the single-dose coffee production button again to start the desalination process, which lasts for 120 seconds. If you want to stop the process earlier, press the single coffee maker button again.
  7. Allow the solution to run through the group without the filter.

WARNING:

  • Rinse the water tank and allow an equal amount of a full tank of drinking water to run through the group to flush the detergent residue.
  • Do not use this water!

SINGLE AND DOUBLE COFFEE QUANTITY ADJUSTMENT

SINGLE COFFEE QUANTITY ADJUSTMENT

  1. Place a heat-resistant container on the grill and under the group.
  2. In standby mode, press and hold the single dose coffee key until the appliance starts producing coffee. Release the button when the amount of coffee reaches the desired. Coffee production time can be set from a minimum of 10 seconds to a maximum of 90 seconds.

DOUBLE COFFEE QUANTITY ADJUSTMENT

  1. Place a heat-resistant container on the grill and under the group.
  2. In standby mode, press and hold the dual coffee maker until the appliance starts to produce coffee. Release the button when the amount of coffee reaches the desired. Coffee production time can be set from a minimum of 15 seconds to a maximum of 90 seconds.

RETURN TO FACTORY SETTINGS

To reset the appliance to the factory settings, press and hold the dual coffee maker, connect the appliance to the power supply. The on / off indicator light will flash twice and the factory settings will be reset.

CLEANING AND MAINTENANCE

Follow these instructions to properly and safely care for your device.

  1. Always disconnect the appliance from the power supply before cleaning or assembling and wait until the appliance has cooled down completely.
  2. Do not immerse the appliance in water or spill water directly on it as this could result in electric shock or fire.
  3. CAUTION: The steam nozzle and all metal parts are hot immediately after use!
  4. CAUTION: Do not use wire brushes or other sharp objects.
  5. Do not use acidic or abrasive detergents.
  6. Clean the housing with a slightly damp cloth without detergent.

GROUP AND HEADWipe the group and the head, inside and out, with a damp cloth. Use a soft sponge to remove stubborn residues. Dry with a soft cloth. You can rinse the group with clean tap water and let it dry well before using it again.

ACCESSORIESYou can clean the filters, the drain pan, the drain pan grille, the dispenser, the water tank and the steam nozzle cover with warm water and mild detergent. Use a soft sponge if necessary. Rinse with plenty of clean water. Dry all parts with a soft cloth.

CAUTION: Not all components can be washed in the dishwasher! Heat and aggressive detergents can cause them to deform and discolor.

WATER TANK

  1. To remove the water tank, open the lid and pull it up with both hands. Replace the tank after cleaning and after it is completely dry.
  2. The water tank has two hooks. Install the water tank by inserting the hooks into the two recesses in the device.
  3. Push the water tank slightly down so that the valve opens at the bottom.

STEAM NOZZLEClean the cover and the steam nozzle immediately after each use. Dry milk residues are difficult to clean.

  1. Remove the cover by turning it gently for easier removal. Use a damp cloth to hold the steam pipe by hand!
  2. Clean it using the cleaning needle.
  3. Let it soak in hot water for a while. This way the milk residue is removed more easily.
  4. Wipe the steam pipe with a damp cloth.NOTE: Fill a container with hot water and insert the steam pipe to remove dry residue.
  5. After cleaning, replace the cover with the steam nozzle. Place a heat-resistant empty container under the steam nozzle.

STORAGE

  1. Always unplug the power cord before storing the device.
  2. Make sure the appliance is cold and dry before storage.
  3. Always store the appliance away from children.
  4. Always store the appliance in a safe and clean place. For the best protection of the device, store it in its original packaging.

TROUBLESHOOTING

report this ad

IONIAS – KALOCHORI, 570 09 THESSALONIKI GREECE, TEL. +30 2310 700777e-mail: [email protected]www.sun.gr

[xyz-ips snippet=”download-snippet”]

Posted

in

by

admin

Tags:

, , , , , ,