synerge RC-U63CDR Universal / DVR Remote Control Instruction Manual

~8214842.docUniversal / DVR Remote ControlModel RC-U63CDR Programming And Operating Instructions(Part # 9-542-906)© 2007, Contec Holdings, LLC, Rev. 06/07

Introduction

Your Synergy ® V Universal / DVR remote control is simple to program, easy to use, and can operate up to five (5) electronic devices, which include:

CABLE Cable set-top terminals
TV Televisions
VCR VCR
DVD DVD
AUDIO Audio receivers, amplifiers, CD players

Before you can use your remote control, it must be programmed (set-up) to operate the above devices.

Before Getting Started

Some of the special features and buttons on your remote control are as follows:

Point and Press ® ProgrammingLet’s program your TV, VCR, DVD, AUDIO devices without using codes. For more information, see sections 5 and 14.

[ALL] SmartKey ®Turn your CABLE set-top terminal and TV on / off with one button press. [ALL] can also be programmed to turn on / off additional electronic devices, or automatically set your correct TV output channel. For more information, see section 9.

[MODE]Indicates which mode (i.e. CBL, TV, VCR, DVD, AUDIO) the remote is currently operating in by illuminating the power button. To change to a different mode, press [MODE], then the power button for the electronic device you wish to operate. For more information, see Section 15.

Memory Guard ®Eliminates reprogramming after battery changes.

Installing / Replacing Batteries

Install two (2) new AA Alkaline batteries. Properly match the “+ / -” ends of the batteries with the diagram in the battery compartment.When the batteries become low and need to be replaced, the [CBL], [TV], [VCR], [DVD], [AUDIO] buttons will not illuminate normally or at all during use, and the remote will no longer operate your devices. When this occurs, replace the existing batteries with two (2) new AA Alkaline batteries to restore normal operation to the remote. For more information, see Section 14.

Programming Your Cable Set-Top Terminal

Your remote control is pre-programmed to operate the Motorola DCT series set-top terminals. To operate a different cable set-top terminal, look up the brand and model in the Cable Setup Code list and follow these steps:

  1. Press [OK], then [MUTE] together until the power/mode buttons illuminate in slow-rotation (i.e. CBL à TV à VCR à DVD à AUDIO –> CBL).
  2. From the Cable Setup Code list, locate the 3-digit code for your brand/model and enter it on the keypad of the remote control. The set-top terminal will turn off.
  3. Then, press [OK] to lock in the code. The power/mode buttons will blink 3-times and go out.

Cable Setup Codes

MotorolaDCTCFT 2200DCT DVR terminals 002002002
Scientific Atlanta
Explorer® 8000 (SARA – RC-U59C)Explorer® 8000 (Passport – RC-U61CPExplorer8600X8600 412413412005005
Pace
510 DigitalHD Digital 412412
Pioneer
Voyager ®BA-V1000, BA-V2000 413007
Tom
5503VIP, 5507, 5508 008
Zenith
 MM 2500Digital 009013

Programming Your TV, VCR, DVD, and AUDIO Devices

Code-Entry Programming

  1. Turn on all the electronic devices (TV, VCR, DVD, AUDIO) you want to program the remote to operate.
  2. Press [OK], then [MUTE] together until the power / mode buttons illuminate in slow-rotation (i.e. CBL àTV à VCR à DVD à AUDIO à CBL…).
  3. a. To program your TV, locate the 3-digit code for your brand in the TV Setup Code list and enter it on the keypad of the remote control. Entry of the correct code will cause your TV to turn off. If multiple codes are listed for your brand, you may have to try several different codes until your TV turns off.b. As soon as you have entered a 3-digit code that turns your TV off, press [MUTE].1. If the TV turns back on, press [OK] to lock in the code. The power/mode buttons will blink 3- times and go out. Or2. If the TV does not turn back on, enter a different 3-digit setup code until your TV turns back on. Then press [OK] to lock in the code. The power/mode buttons will blink 3-times and go out.
  4. To program your VCR, refer to the VCR / DVD Setup Code lists and repeat steps 2 and 3 above.
  5. To program your DVD, refer to the VCR / DVD Setup Code lists and repeat steps 2 and 3 above.
  6. To program your AUDIO equipment, refer to the AUDIO Setup Code list and repeat steps 2 and 3 above.

Point and Press ® Programming

This method allows you to program the remote control without using codes. Instead, the remote control automatically finds the correct command that you select in a variety of codes until you find the code that operates your device. You then lock in the correct code as described below.

The following instructions describe how to program your remote control using the [CH +] or [CH -] buttons (“Power” function during programming). You may also program your remote control using other buttons/functions as described in Section 14. When using this method, there are several important points to remember:

  • The order in which you program your electronic devices is not important.
  • There may be several codes that turn your electronic devices on / off (or perform other functions). Once you lock in a code, be sure to check the available functions for that device (i.e. TV – Vol +/-, Mute, TV Input (Input button); VCR – Play, Stop..; DVD – Play, Stop…; AUDIO – Vol +/-, Mute) to see if they are operating.
  • While the remote is searching for the correct setup code(s) for your electronic devices, it is possible that other (previously programmed) devices may turn on / off (or perform other functions). If this occurs, continue pressing the [CH +] or [CH -] buttons (or the buttons described in Section 14) until you find the correct code for the device you are programming.
  • It may take several minutes for the remote to find the correct code that turns your device off (or performs another selected function). During this time, the power/mode buttons will illuminate in fast-rotation (i.e. CBL à TV à VCR à DVD à AUDIO à CBL…).

Programming your electronic devices using the [Ch +] or [Ch -] buttons (“Power” function during programming)…

  1. Turn on all the electronic devices (TV, VCR, DVD, AUDIO) you want to program the remote to operate.
  2. Press [OK], then [MUTE] together until the power/mode buttons illuminate in slow-rotation (i.e. CBL à TV à VCR à DVD à AUDIO à CBL…).
  3. Press and hold the [CH +] button until one device turns off. While you are pressing the [CH +] button, the power/mode buttons will illuminate in fast rotation. As soon as one device turns off, release the [CH +] button.
  4. Press [MUTE]. If the device that turned off…a. Turns back on, press [OK] to lock in this code. The power/mode buttons will blink 3-times and go out. Orb. Does not turn back on, press [CH -] one step at a time until that device turns back on. Each time you press the [CH -] button, the power/mode buttons will illuminate once in reverse fast-rotation (AUDIOà DVD à VCR à TV à CBL). Once you have found a code that turns the device on / off, press [OK] to lock in this code. The power/mode buttons will blink 3-times and go out.
  5. Repeat steps 2 to 4 above for each of the remaining electronic devices you wish to program the remote to operate.

Programming Your TV / VCR Combination

  1. First, turn on your TV / VCR combination device and install a VHS tape.
  2. Next, program your remote to operate the TV functions of your combination device. Using the Code Entry Programming method described in Section 5, find a TV Setup Code that operates the TV functions (Power, Vol +/-, Mute) of your combination device.
  3. Last, program your remote to operate the VCR functions of your combination device.Using the Code Entry Programming method described in Section 5, enter, lock and test each 3-digit VCRSetup Code for your brand until a code is found that operates the transport functions (Play, Stop, Rew,Pause, Rec) functions of your TV / VCR combination device.Before you can test for the correct VCR setup code, you must first press the [MODE] button, then the [VCR] button to put the remote in its VCR mode.

Programming Your TV / DVD or TV / VCR / DVD Combination

  1. First, turn on your TV / DVD combination device and install a DVD.
  2. Next, program your remote to operate the TV functions.Using the Code Entry Programming method described in Section 5, find a TV Setup Code that operates theTV functions (Power, Vol /, Mute, Ch /, 0-9) of your TV / DVD combination device.
  3. Last, program your remote to operate the DVD functions.Using the Code Entry Programming method described in Section 5, enter, lock and test each 3-digit DVDSetup Code for your brand until a code is found that operates the transport functions (PLAY, STOP, REW, FWD, PAUSE, REC) of your TV / DVD combination device. Before you can test for the correct DVD setup code, you must first press the [MODE] button, then [DVD] button to put the remote in its DVD mode.
  4. If you have a TV / VCR / DVD combination device, you would then program your remote to operate the VCR functions.Using the Code Entry Programming method described in Section 5, enter, lock and test each 3-digit VCR Setup Code for your brand until a code is found that operates the VCR transport functions (PLAY, STOP,REW, FWD, PAUSE, REC) of your TV / DVD / VCR combination device.Before you can test for the correct VCR setup code, you must first press the [MODE] button, then [VCR] button first to put the remote in its VCR mode.

TV Setup Codes

AdmiralAdventAdventuraAiwaAkaiAmarkAmstradAnam 026 054 211 213072 094 425 447 46047214053 462023 215157217 218 219 220 221222 223
AOCAPEXAudiovoxBelcorBell & HowellBroksonicBrokwoodCandleCenturionCitizenConcertoContecCoronadoCraigCrownCurtis MathesDaewoo 053030 038 427220073211 213165 167073068 091095 107 108068 091 211 213 233073 095147023223023016 054 107 108 211  213051    068     073     095   158159  189  191  194  196197  198  200  202  204205  206  207  209
DaytronDellDumontDynexElectro HomeElektraEmerson 073 095 107 108448073423  424073 095353016 023 053 064 103139 158 159 164 165166 167 168 169 392400 401 402 408 415
EnvisionESAFisherFunaiFujitsuGatewayGE 073 095454 456355 356047 048 157 168 211460426015 018 042 044 049054 055 068 073 090095 101 102 103 389390 396 403 406 407092
Gibralta 023 048 053 068 073090 095 107 108 233360
Goldstar (LG) 023 053 068 073 090107 108 233 360 361
GradienteGrundigGo VideoHall Mark 104233443073 095
Hitachi 023 068 095 096 097098 099 100
HyundaiInkelInsignaJC Penney 453364450 456 461039 053 068 073 092095 102 355
JensenJVC 062104 105 106 396 397410
KawashoKMCKTVKonkaKurazaiLG (Goldstar) 073 095023023 053 233 366445211 213023 053 068 073 090107 108 233 360 361
LodgenetLogikLuxmanLXI 211 213211 213068 073 095024 026 157 345 355388
Magnavox (Philips) 023 068 071 072 073089 090 091 092 093094 134 385 387 397404 463
MajesticMarantzMegatronMemorex 211 213053 107 108 109215090 211 213 355 388405
MGA / Mitsubishi 053 068 073 090 095107 109 110 216 384394 395 398 399 417108
Montgomery Ward 022 023 026 053 071072 108 211 213
NECNet TVNorcentOrion 028 068 090 108 200426455019 159 160 161 162163 382
Panasonic 042 043 044 045 046429
Philco 023 053 068 071 072091 463
Magnavox (Philips) 023 068 071 072 073089 090 091 092 093094 134 385 387 397404
PilotPioneePortlandProScanProtonProviewPulsarQuasarRadio ShackRealisticRCA 073 094 233111 144 551 383  551   551023 068055 070090 371 372 457459073044073022 166 168042 052 053 054 055069 070 416 068
SampoSamsung 090 108015 016 017 023 031090 107 108 134 147151 153 386 411
SansuiSanyoScottSears 423 424353 355 356 376 377090 108 168023 031 038 039 068353 355 356
Sharp 016 022 023 024 025026 027 028 029 393395 409
Signature 2000SonySoundesignSquareviewSupre-MacySylvania 023 026 108 211 213014 020 021091157380068 071 072 090 091093 107 108 157 158419 092
SymphonicTatungTechwoodTeknika 047 157044 446068023 068 072 091 168213 463
TalentTeraTevionTMKToshibaTelevisionUniversalVtech 023 213381065 414068 090030 031 038 039233068 102068
ViewSonicWardsWhite WestinghouseXR-1000YamahaYorkZenith ViewSonicWardsWhite WestinghouseXR-1000YamahaYorkZenith

VCR Setup Codes

Admiral?AdventuraAiwaAkai 066 075132269 275 336 351 352354
Audio DynamicsBell & HowellBroksonicCanonCitizenColortymeCraigCurtis MathesDaewoo 243 291357 238333 337 358 359086 362033 172 247 331291172 363086 112 247 291033 343 344 345 346347
DaytronDBXDynatechEmerson 345 365243 291132033 086 132 326 327331 332 333 334 335336 337 338 339 340341 342
FisherFunaiGEGo VideoGoldstar (LG)Harman KardonHitachiInstant ReplayJC PenneyJCLJVC 035 081 357 363132086 172 174 170348 349 350247 331291078 132086078 086 172 238 291086120 128 243 247 250253 238
KenwoodLG (Goldstar)LloydLogikLXIMagnavox (Philips)Marantz 120 132 238 243 247247 331132367132 331086 132 183086 172 183 238 247291
 

MartMatsuiMemorex

 

 291331368132 238 331 363 369370
MitsubishiMTCMontgomery Ward Multi TechNEC 255 258132 172066 170 173 373132 172 367120 238 243 291 374375
Orion 322 326 327 328 329330 

 
PanasonicPentaxPhilcoPhilips (Magnavox)PioneerPortlandProScanQuartzQuasarRCA 112 117 430 086078086 132 183086 132 183078 120 263345170 174238 378112078 132 141 170 172173 174 086
RealisticSamsungSansuiSanyoScottSearsSharpShintomSignature 2000SonySoundesignSylvania 066 132 238 363269 271 275 276 278120 367 379238 346 357 363033 332 367035 078 238 331 363066 075367066 170 173 373056 058 060132086 132 141 183 184322 324 420
SymphonicTandyTashikoTatungTeacTechnicsTeknikaThomasTMKToshibaTotevisionUnitechVector ResearchVideo ConceptsWardsXR-1000YamahaZenith 132132 238331243132 243086132 331 359132338033 035 078 081172 331172291132 291066 132 172 247 331367132 243 291 238058 120 122 128 132435
DVD Setup Codes
Apex DigitalB144DenonDVD-VideoECAGEGoldstar (LG)GradienteHarmon KardonHitachiJVCKenwoodKLHLG (Goldstar) MagnavoxMarantzMintekMitsubishiNADOnkyoPanasonicPioneerProceedSamsungSharpSonySylvaniaThomsonToshibaYamahaZenith 193 227146201 203199156150 152 156 175129 133 135 179 260212 234256 259149177 179228248 252129 133 135 179 260138 143 146270432181 185246085 244115 118 121 124 431125 187 188236192 224 225034 076 077 079040 059 061 436421156 237082 085 087 113121 124 210129 133 135
Audio Setup Codes  Compact Disc
ADCAkaiAiwaCarverCrownDenonFisherGoldstar (LG)Harman KardonJVCKenwoodKrolLG (Goldstar)Magnavox (Philips)MissionMitsubishiNADNakamichiNECNSMOnkyoPanasonicPhilips (Magnavox) PioneerQuasarRadio ShackRCASanyoSAEScottSharpSonySoundesignSTSSylvaniaTeacTechnicsToshibaYamaha 318249 261176176 155154273230 274308315297131 176 274 289 299176308037 084 119 296176245 249182 231 290264 319235176300184 266 437037 084 119 296 433116 127184186 190 266 279 289295 037 119230 309176186288 289067 292 293148 242 311 320318084186184 208 317290280
Receiver / Amplifier
AdcomAiwaAkaiBoseCarverDenonEverquestFisherFosgate AudionicsGoldstar (LG)Harman KardonHitachiJensenJVCKenwoodLG (Goldstar)LuxmanMagnavoxMarantzNADOnkyoOptimusPanasonicParasoundPhilips (Magnavox)PioneerQuasarRadio ShackRCARealisticRoteSansuiSanyoScottSharpSherwoodSonySoundesignSSITaekwangTeacTechnicsWardsVictorYamahaZenith 325301142302 440155 180262 307136063 180305036130 257 305 306240140114 241063 277 444036281080282 283 284 285286126 171 304142 229 321032 074 438 441323080123 137 251 298032229 267439226 268310283195272294229 267041 057 232 287 442083 088 239 265313142314 316032063114 241145 254 303036 083 088 239 265

Code Number Read-Back

To identify the 3-digit TV setup code stored under the Point and Press ® programming method, follow these steps:

  1. Press [TV], then [OK] together until the [TV] button illuminates.
  2. Press [INFO]. The power/mode buttons will “blink back” the code numbers, with a 1-second interval between each digit of the code. Please note that for the numeric “0”, the mode buttons will illuminate blink in fast-sequence.Example: For code “130”, the power/mode buttons will blink 1-time, then 3-times, then in a fast-sequence for the 0.

To identify the 3-digit VCR code, press [VCR], then [OK] in step 1, then press [INFO].To identify the 3-digit DVD code, press [DVD], then [OK] in step 1, then press [INFO].To identify the 3-digit AUDIO code, press [AUDIO], then [OK] in step 1, then press [INFO].

ALL SmartKey®

Once you have programmed the remote to operate your electronic devices, you can press the [ALL] SmartKey ® to turn your Cable set-top terminal and TV on / off with one button press. You can also program the [ALL] button to turn on / off additional electronic devices and/or tune your TV to its correct output channel.

Programming the [ALL] SmartKey ®

  1. Press [ALL], then [MENU] together until the [CBL] button illuminates.
  2. Enter one of the following options on the keypad of the remote:[0] – Turns on / off CBL + TV (default setting)[1] – Turns on / off CBL + TV and tunes TV to output Channel 3.[2] – Turns on / off CBL + TV and tunes TV to output Channel 2[3] – Turns on / off CBL + TV and tunes TV to output Channel 4.[10] – Turns on / off CBL + TV + VCR + DVD[4] – Turns on / off CBL + TV + VCR + DVD and tunes TV to output Channel 3.[5] – Turns on / off CBL + TV + VCR + DVD and tunes TV to output Channel 2.[6] – Turns on / off CBL + TV + VCR + DVD and tunes TV to output Channel 4.[11] – Turns on / off CBL + TV + VCR + DVD + AUDIO[7] – Turns on / off CBL + TV + VCR + DVD + AUDIO and tunes TV to output Channel 3.[8] – Turns on / off CBL + TV + VCR + DVD + AUDIO and tunes TV to output Channel 2.[9] – Turns on / off CBL + TV + VCR + DVD + AUDIO and tunes TV to output Channel 4.[12] – Turns on / off CBL + TV + AUDIO[13] – Turns on / off CBL + TV + AUDIO and tunes TV to output Channel 3[14] – Turns on / off CBL + TV + AUDIO and tunes TV to output Channel[15] – Turns on / off CBL + TV + AUDIO and tunes TV to output Channel 4
  3. As soon as you select an option, the [CBL] button will blink 3-times and go out.

Using the [ALL] SmartKey ®When pressing the [ALL] SmartKey ®, be sure to keep the remote control aimed at your electronic devices until your electronic devices turn on or / off.Whenever the [ALL] SmartKey® is pressed, the mode of the remote control will automatically switch back to Cable.

Volume Control

When you first program your remote, volume/mute are controlled through your TV (except AUDIO which defaults to the AUDIO device). The volume control options in each mode of the remote are:CBL TV (default), Cable, or Audio.TV TV (default), Cable, or Audio.VCR TV (default), Cable, or Audio.DVD TV (default), Cable, or Audio.AUDIO AUDIO device (default), Cable, or TV.To control volume/mute through your Cable set-top terminal in the remote’s Cable mode…

  1. Press [CBL], then [OK] together until the [CBL] button illuminates.
  2. Press [VOL +], then [CBL] for Cable volume. The [CBL] button will blink 3-times and go out.To return volume control to your TV, repeat step 1, then press [VOL +], then [TV] in step 2

Channel Memory Button

Your remote has 1 Channel Memory button (See Section 15) which can store up to 5 cable channels. This button may come pre-set/labeled to channels selected by your cable operator. If this button has not been pre-set by your cable operator, it can be programmed as follows:Programming Channel Memory ButtonTo program the [Channel Memory] button to cable channels 1, 12, 123, 1234, 17, follow these steps:

  1. Press [Channel Memory], then [CBL] together until the [CBL] button illuminates.
  2. Enter each channel as follows (ex. assumes 4-digit channel format):a. Enter 1 st channel # – 0001.b. Press [CH +] to advance to the next channel # setting.c. Enter 2nd channel # – 0012.d. Press [CH +] to advance to the next channel # setting.e. Enter 3 rd channel # – 0123.f. Press [CH +] to advance to the next channel # setting.g. Enter 4 the channel # – 1234.h. Press [CH +] to advance to the next channel # setting.i. Enter 5 the channel # – 0017.
  3. Press [Channel Memory] to store the above channels. The [CBL] button will blink 3-times and go out. To store fewer than 5 channels, you can press the [Channel Memory] button any time after entering a complete channel number.

Using Channel Memory ButtonUsing the above-programmed channels as an example…

  1. Press [Channel Memory] – Cable set-top terminal tunes to channel 0001.
  2. Press [Channel Memory] again – Cable set-top terminal tunes to channel 0012.
  3. Press [Channel Memory] again – Cable set-top terminal tunes to channel 0123.
  4. Press [Channel Memory] again – Cable set-top terminal tunes to channel 1234.
  5. Press [Channel Memory] again – Cable set-top terminal tunes to channel 0017.
  6. Press [Channel Memory] again – Cable set-top terminal tunes to channel 1….repeat.

Whenever the Channel Memory button is pressed, the function of the transport buttons will automatically switch back to Cable.When pressing the Channel Memory Button, be sure to keep the remote control aimed at your Cable set-top terminal to ensure the full channel numbers are received in their entirety.If you are using your Synergy ® V remote to operate a Cable set-top terminal other than the Motorola 62xx series DVR model, you may only have to enter channels in a 3-digit format (ex. 012).

Input

This button changes the input source of your electronic devices. In the remote’s Cable mode, this operates a Cable function. In the remote’s TV mode, this button changes the Input Source (Input 1, Input 2…) on your TV. In the remote’s VCR mode, this button changes the TV / VCR Input on your VCR.You can program this button so that in the remote’s Cable mode, [INPUT] will operate the Input function on your TV or VCR, eliminating the need to change modes on the remote.To program [INPUT] to operate your TV Input function in the remote’s cable mode…

  1. Press [INPUT], then [OK] together until the [CBL] button illuminates.
  2. Press [TV]. The [CBL] button will blink 3-times and go out.Note: You can also press [VCR] in step 2 above to operate the TV / VCR input on your VCR. Or press [CBL] to return to the normal CBL Input function.

Reset

To reset your remote to its factory default settings, follow these steps:

  1. Press [CBL], then [OK] together until the [CBL] button illuminates.
  2. Press [1]. The [CBL] button will blink 3 times and go out.Reset returns all programmable features to their factory default settings.

Additional Programming Information, Troubleshooting, Terms

Additional Programming Information

  1. The power/mode buttons will illuminate in slow rotation (i.e. CBL→ TV→VCR→DVD→AUDIO→CBL…) while the remote is in a programming model. In the absence of a keypress entry, the power/mode buttons will stop illuminating after 45 seconds and the remote will exit the programming mode.
  2. When programming the remote control using the [CH +] or [CH -] buttons (Power function) in the Point and Press ® Programming method, you may find a code that turns a device off but not back on. If this happens…a. The correct code has not been found as you may have a code that operates some but not all of the functions of your device. Continue pressing [CH +] until your device turns on.ORb. You may have gone past the correct matching code. Try pressing [CH -] one press at a time until you find a code that turns your device back on.
  3. When using the Point and Press® Programming method, you can also program your remote using buttons other than the [CH +] or [CH -] as described in Section 5 as follows:a. [VOL +] – to “go forward” through the codes using the “VOL +” function on your devices.b. [VOL -] – to “go back” through the codes using the “VOL -“ function on your devices.Note: When you find the correct code, the volume of the device being programmed will increase or decrease.c. [] – to “go forward” through the codes using the “CH +” function on your devices.d. [] – to “go back” through the codes using the “CH –“ function on your devices.Note: When you find the correct code, the channel of the device being programmed will increase or decrease.e. [] – to “go forward” through the codes using the “Fast Forward” function on your devices.f. [] – to “go back” through the codes using the “Rewind” function on your devices.Note: When you find the correct code, the fast-forward or rewind function of the device being programmed will be performed. To simplify programming using these buttons, insert a VHS tape or DVD in the device being programmed.
  4. Your remote is equipped with a Point and Press® Programming label on the back of its case. This will help you quickly program the remote without using codes.

Troubleshooting / Tips

  1. If the same button is pressed and held for 30-seconds, your remote control will turn itself off automatically. This extends the battery life should the remote become lodged under or between heavy objects, for example, sofa cushions.
  2. When the batteries become low and need to be replaced, the [CBL], [TV], [VCR], [DVD], [AUDIO] buttons will not illuminate normally or at all during use, and the remote will no longer operate your devices. When this occurs, replace the existing batteries with two (2) new AA Alkaline batteries to restore normal operation to the remote. If your remote still does not operate, you may want to check to see if one of the buttons is stuck in its “down” position.
  3. If you have a TV that’s operated by remote control, it is recommended that you plug it directly into a wall outlet instead of the cable set-top terminal.
  4. If you have any questions concerning the brand, model, or operation of your cable set-top terminal, contact your cable operator.

Frequently Used TermsAUDIO Devices – Audio receivers, amplifiers, CD players that you can program your remote to operate.DVR – Digital Video Recorder.Default Setting – How your remote is set when you receive it from your cable operator.Electronic Components / Devices – The various electronics device the remote is designed to operate. These include cable set-top terminals, TVs, VCRs, DVDs, audio-video receivers, amplifiers, and CD players.Fast-Rotation – The power/mode buttons will illuminate in a fast-rotation (i.e. CBL→TV →VCR →DVD→AUDIO→CBL…) repeated every 1/3 second. Fast-rotation occurs when the remote is receiving keypresses to program it to your electronic devices.IPG – Interactive Program GuideMode – The device the remote is set to operate (ex. Cable, TV, VCR, DVD, Audio)OSD – On Screen DisplayPIP – Picture-in-picture functionality through your Cable set-top terminal.Program (Setup) – The process of teaching your remote control to operate your electronic devices.Slow-Rotation – The power/mode buttons illuminate in a slow-rotation (i.e. CBL→TV → VCR → DVD→AUDIO→CBL…) repeated every 1 second. Slow-rotation occurs when the remote is in the programming mode, waiting for the next entry on the keypad of the remote.TV Output Channel – The channel your TV needs to be set on for proper Cable reception (most often TV channel 3,but maybe TV channel 2 or 4). If you have any questions concerning your TV output channel, contact your cable operator. Or, with your cable set-top terminal turned on, try setting your TV to channel 2, 3, or 4 to obtain a clear picture.Transport Functions – These are the [STOP], [PLAY], [FWD], [REW], [PAUSE] and [REC] buttons. In the remote control’s Cable mode, these buttons operate your Cable set-top features. In the remote control’s VIDEO mode, these operate your VCR or DVD functions.VIDEO Devices – VCR or DVD players.Device Setup CodesIf you find that the setup codes listed above do not operate your devices, it is possible your remote was manufactured before the revision date printed on this Instruction Manual. If this occurs, contact your cable operator and request a newer version of your remote control.Rev. 06/07© 2007, Contec Holdings, LLCU.S. Patents 7,109,908 & 6,507,306 & D491,925Point and Press ®Memory Guard ®, SmartKey ®, and Synergy® are registered trademarks of Contec CorporationExplorer ® is a registered trademark of Scientific-Atlanta, Inc.Voyager ® is a registered trademark of Pioneer Digital Technologies, Inc.Passport ® is a trademark of Pioneer Digital technologies, Inc.

Using Your Synergy® V – Universal / DVR Remote Control

Important: The following diagram shows how to use the buttons on your remote control to operate the DVR and PIP functions of the Motorola DCT series DVR set-top terminals. To access these functions, set the remote control to its Cable mode by pressing the [MODE] button, followed by the [CBL] button.

report this ad

For Reference –*OSD – On Screen Display*IPG – Interactive Program Guide

[xyz-ips snippet=”download-snippet”]

Posted

in

by

admin

Tags:

, , ,