Tenda 8-Port Gigabit Ethernet SwitchInstallation Guide
Model: TEG1008M
Package contents
- Switch * 1
- Power adapter * 1
- Quick installation guide * 1
If any item is missing, damaged or incorrect, please keep the original packaging and contact the local reseller or distributor immediately.
1. Installing the switch
Select one mounting method as required.
Option A. Desktop mounting
Put the switch on a stable and flat desktop.
Option B. Wall mounting
Step 1: Drill two holes in the wall in a horizontal distance of 116 mm. Knock sleeve anchors (self-preparation) into the holes using a rubber hammer till the sleeve anchor is level with the wall. Then tighten two screws (self-preparation) into the sleeve anchors using a screwdriver, and keep the screw heads outside the wall at least 2.7 mm, to ensure that the switch can be hung on the screws firmly.
Step 2: Align the slots of the switch to the screw heads, and slip the switch to make it fixed on the screws firmly.
Note: For safety, do not face the air vents of the switch down
2. Connecting your devices
Tip:All ports of your switch support the auto MDI/MDIX function, indicating that either straight cable or crossover cable is acceptable to connect your switch to Ethernet devices.
Specifications
LED indicators
CE Mark Warning
This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.The mains plug is used as disconnect device; the disconnect device shall remain readily operable.
NOTE: (1) The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. (2) To avoid unnecessary radiation interference, it is recommended to use a shielded RJ45 cable.
Caution:
Adapter Model: BN049-A05009E/BN049-A05009BManufacture: SHENZHEN HEWEISHUN NETWORK TECHNOLOGY CO., LTD.Input: 100 – 240 V AC 50/60 Hz, 0.3 AOutput: 9 V 0.6 A; DC Voltage
RECYCLING
This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE). This means that this product must be handled pursuant to European directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment.
User has the choice to give his product to a competent recycling organization or to the retailer when he buys a new electrical or electronic equipment.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Caution!
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: (1) The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. (2) To avoid unnecessary radiation interference, it is recommended to use a shielded RJ45 cable.
Copyright
Copyright © 2019 Shenzhen Tenda Technology Co., Ltd. All rights reserved.Tenda is a registered trademark legally held by Shenzhen TendaTechnology Co., Ltd. Other brand and product names mentionedherein are trademarks or registered trademarks of their respectiveholders. Specifications are subject to change without notice.
Technical Support
Shenzhen Tenda Technology Co., Ltd.6-8 Floor, Tower E3, NO.1001, Zhongshanyuan Road, NanshanDistrict, Shenzhen, China. 518052USA hotline: 1-800-570-5892Canada hotline: 1-888-998-8966Hong Kong hotline: 00852-81931998Website: http://www.tendacn.comE-mail: s
[xyz-ips snippet=”download-snippet”]