TENERGY Smart Touchless Vac-Bin
IMPORTANT SAFETYINSTRUCTIONS
This electrical appliance must always be used according to the following safety instructions. Save these instructions as this manual contains important safety and operating information. When using an electrical appliance, basic precautions should always be followed, including: READ ALL INSTRUCTIONS CAREFULLY BEFORE USING THE APPLIANCE WARNING! To reduce the risk of fire, electrical shock, or injury:
- Always turn the power OFF before unplugging.
- Always unplug the appliance before cleaning or servicing. Do not unplug by pulling the cord; to unplug, grasp the plug, not the cord.
- Do not let the appliance be used as a toy. Close attention is necessary when used near children. Do not use in AUTO mode or leave appliance plugged in near small children or infants.
- Do not pull or carry the appliance by the cord. Keep the cord away from heated surfaces.
- Do not use the appliance if the cord or plug is damaged.
- Do not handle the plug or appliance with wet hands.
- Do not use appliance on wet surfaces.
- Do not expose to rain.
- Do not use appliance to dispose of water or damp materials such as mud, tile gout, plaster filter, or caulking. Do not use to vacuum any liquid or wet objects.
- Do not use this appliance to vacuum up burning or combustible liquid, such as gasoline. Do not use in areas where these liquids may be present.
- Do not use this appliance to vacuum up burning or smoking materials, such as cigarettes, matches or hot ashes.
- Keep hair, loose clothing, and all parts of the body, fingers, away from openings and moving parts.
- Do not force any objects into appliance openings.
- Do not use this appliance to vacuum hard or sharp objects or large surface litter. Pick these up by hand before vacuuming.
- Do not operate without the Collection Bin properly in place.
- Use the appliance only as described in this User Manual.
- Turn the appliance off and unplug before removing or replacing the inner Collection Bin or filter.
- Unplug appliance before cleaning or maintenance.
- If the appliance is not working as it should, review the Trouble Shooting section on page 6, and then call for instructions where to send for repair. Do not attempt to repair, as it will invalidate your warranty.
- When cleaning the outside of the appliance, wipe with a damp cloth to reduce the static electricity on the outer surface.
WARNING: In order to prevent electric shock, do not use on wet surfaces. Do not expose to rain. Store indoors.
DESCRIPTION OF SMART TOUCHLESS VAC-BINCONTROL PANEL DESCRIPTION
Image # | Display | Description |
1 |
POWER |
Press to turn unit on. Press again to cycle through modes. Hold for 3 seconds to turn unit off. |
2 |
AUTO |
Automatic vacuum mode |
3 |
MAN |
Manual vacuum mode |
4 |
FULL |
Collection Bin full indicator |
5 |
START/OFF |
Press to start or stop vacuum cycle |
6 |
OPEN |
Press to open waste bin lid |
7 |
CLOSE |
Press to close waste bin lid |
8 |
INDICATOR LIGHT | Blue – Waste bin lid open Red – Waste bin lid closed |
BEFORE FIRST USE HEPA FILTER AND WASTE BAG INSTALLATION
1. Remove the included HEPA filter from plastic bag and install it into Collection Bin’s filter slot with flaps facing upward.2. Remove Collection Bin and unlock side clips to separate the upper part from the bottom part of Collection Bin. (see fig. a & b)3. Insert any appropriate sized waste bag into the bottom part of the Collection Bin. Re install the upper part of the bin and lock in place with side clips. Replace Collection Bin into the waste bin. The waste bin is ready for use.
SENSOR WASTE BIN OPERATION INSTRUCTION
- Press the POWER button to turn the unit on. A Blue Indicator Light under AUTO will illuminate indicating the unit is on and ready to use.
- Place your hand or any object 4 – 12 inches above Lid Sensor to open waste bin lid automatically. (see fig. c) The lid will remain open if Infrared Sensor in front of the waste bin detects people or object within its range.
- To manually open and close waste bin lid, press OPEN and CLOSE buttons.
- When the Collection Bin is full, the indicator light FULL will flash and beep audibly.
- Utilize Infrared Sensor or press OPEN to open the waste bin lid. Follow WASTE BAG INSTALLATION steps above to remove and replace the waste bag.Note: Waste bin lid will not open during a vacuuming cycle.
VACUUM OPERATIONINSTRUCTION
- Press the POWER button to power on. A Blue Indicator Light under AUTO will illuminate. The vacuum defaults to Auto Mode for automatic use when turned on.
- Sweep debris toward the inlet at the base of the unit. The infrared sensors will detect the debris and automatically initiate a timed vacuuming cycle of 5 seconds.
- Activate Manual Mode by pressing the POWER button again. The Blue Indicator Light will illuminate under MAN. Sweep debris toward the inlet at the base of the unit, press the START/OFF button or gently tap the Manual Vacuum Kick-Switch to initiate a timed vacuuming cycle of 5 seconds.Note: You may utilize the manual vacuum Kick-Switch to start and stop vacuum cycle during Auto or Manual Mode.
COLLECTION BIN CLEANING INSTRUCTION
- Press and hold the POWER button for 3 seconds to turn off the unit. Unplug Power Cord from AC outlet.
- Open waste bin lid, lift handle to remove Collection Bin from the unit.
- Unlock side clips and remove waste bag (Refer to Waste Bag Installation instructions above).
- Wash Collection Bin by hand in warm water with mild soap. Avoid using harsh chemical or abrasive cleaning material. Rinse and dry thoroughly. The Collection Bin is NOT dishwasher safe.
- Gently clean sensors and dirt inlet area with a damp cloth. Do not scrub or use abrasive cleaning materials.
- Replace Collection Bin back into the unit. If Collection Bin is improperly installed, an audible Beep will sound once the unit is plugged in and powered back on.
HEPA AND AIR OUTLET FILTERS CLEANING INSTRUCTION
It is recommended to clean the HEPA and Air Outlet filters periodically to keep the Smart Touchless Vac-Bin operating at peak performance. Poorly maintained HEPA and Air Outlet filters may collect debris to cause obstruction in vacuum’s air flow and significant degrade performance.
- Press and hold the POWER button for 3 seconds to turn off the unit. Unplug Power Cord from AC outlet.
- To remove HEPA filter, open waste bin lid, lift and remove HEPA filter from its housing. (see fig. a)
- To remove Air Outlet filter, press the filter holder in the back of the unit, the holder will pop open. (see fig. b& c)
- Rinse both filters under cold running water for two minutes until water runs clear and filter is clear from any visible debris.
- Dry filters thoroughly before inserting back into housing placements.
IMPORTANT! NEVER OPERATE THE MACHINE WITHOUT HEPA OR AIR OUTLET FILTER PROPERLY IN PLACE.
STORAGE INSTRUCTION
- Press and hold the POWER button for 3 seconds to turn off the unit. Unplug Power Cord from AC outlet.
- Thoroughly clean the unit by follow Collection Bin Cleaning Instructions and HEPA and Air Outlet filter cleaning instructions on page 5.
- Unplug Power Cord from the back of the unit and store it inside Collection Bin. Never wrap cord tightly around the unit, bending cord in sharp angles may cause breakage.
- Store the Smart Touchless Vac-Bin indoors in a clean, dry place. Never store the unit when it is still plugged in.
WARNING! TO AVOID ELECTRIC SHOCK, DO NOT USE THE SMART TOUCHLESS VAC-BIN OUTDOORS OR IN WET SURROUNDINGS.
TROUBLE SHOOTING
Problem | Possible Cause | Possible Solution |
Smart Touchless Vac-Bin does not power on | 1. Not firmly plugged in
2. Unit is in off status 3. Collection bin is not in position 4. No power in wall plug 5. Blown house fuse or tripped circuit breaker 6. Cover is not closed |
1. Plug in firmly
2. Press POWER button and switch mode between AUTO and MAN 3. Reinstall Collection Bin 4. Check house fuse or circuit breaker 5. Have a qualified licensed electrician replace house fuse or reset circuit breaker 6. Press the close button |
Does not run,
audible beep. |
Collection Bin is not in-place or
improperly placed inside the unit |
Re-install the Collection Bin correctly |
Does not vacuum | 1. Dirt Inlet is blocked
2. Collection Bin is full 3. Debris too large for inlet |
First power off unit
1. Clean path of Dirt Inlet 2. Empty Collection Bin 3. Clear large debris |
Sensors do not
activate |
Unit is not on AUTO mode | Press POWER button to cycle to AUTO
mode |
Suction is not strong | Filters may be dirty | Clean both HEPA and Air Inlet filters by follow filter cleaning instructions
on page 5 |
Waste bin lid won’t close | 1. Objects are detected
2. Collection Bin handle is improperly placed |
1. Remove object
2. Swing Collection Bin handle to the other side |
LIMITED WARRANTY
Tenergy warrants its product shall be free from defects in materials and workmanship, under normal conditions and use, for a Limited Warranty Period of twelve (12) months from the date of original purchase. This warranty is not applicable to cases other than defects in material and workmanship. This warranty is only valid upon presentation of the proof of purchase which include the original invoice or sales receipt indicating the date of purchase, store name, model and serial number or UPC of the product. In no case shall Tenergy Corporation’s liability be greater than the actual purchase price of this product. This limited warranty does not cover normal wear and tear, water damage, or other alleged defect or nonconformity that is a result of abuse, misuse, neglect, tampering, unauthorized or improper use or installation, disassembly, repair, alteration, or accident by Purchaser. Please make all warranty claims to Tenergy Customer Service at Tenergy Customer Service at [email protected]
[xyz-ips snippet=”download-snippet”]