Thomann BOTEX 1 Channel Dimmer CT-110R User Manual
User manual
This manual contains important information on the safe operation of the product.Read and follow the safety advice and instructions given. Retain the manual for future reference. If you pass the product on to others please include this manual.
Safety instructions
Intended use
This device is used as a one-channel dimmer control for inductive loads. Any other use or use under other operating conditions is considered to be improper and may result in personal injury or property damage. No liability will be assumed for damages resulting from improper use.
Danger for children
Ensure that plastic bags, packaging, etc. are disposed of properly and are not within reach of babies and young children. Choking hazard! Ensure that children do not detach any small parts from the product. They could swallow the pieces and choke! Never let children unattended use electrical devices.
Danger to life due to electric shockThe electrical wiring may only be made by a qualified electrician.
Where to use the product
Never use the product
- in conditions of extreme temperature or humidity
- in extremely dusty or dirty areas
- at locations where the unit can become wet
General handling
- To prevent damage, never use force when handling the product.
- Never immerse the product in water. Just wipe it with a clean dry cloth. Do not use liquid cleaners such as benzene, thinners or flammable cleaning agents.
Features
- Dimmer and Flash function
- 0 – 10 V control
- Connections via terminals
- Up to 5 devices can be interconnected
Operating elements
- FUSE: Fuse holder
- LED: shows the channel intensity
- Slider: controls the intensity between 0 and full
- FLASH: button for full output signal
Connections
- To connect the device, screw open the housing.
- The pre-punched holes on the back of the unit can be broken up and used to feed through the cables.
- Connect the load to be controlled to the terminals ‘LOAD’.
- If desired, connect an external control (0 – 10 V) to the ‘LINK UP’ terminals.
- Make sure that the power cord to be used is not connected to the mains. Then connect the wires of the power cable to the terminals ‘AC IN’.
- Orient yourself by the graphic on the right if you want to interconnect up to 5 devices.
- Set the switch behind the ‘LINK UP’ terminals to the ‘LINK’ position to operate the unit in Slave mode. Set the switch to the ‘SEL’ position to operate the unit in Master mode.
- Close the device housing and refit the screws.
- Connect the power cord to the mains.
Using the product
- Control the connected load with the slider. The LED indicates the current intensity.
- Press the FLASH button for full output.
- After use, unplug the power cord from the mains.
Technical specifications
- Control principle: Leading edge phase control
- Dimmer output: 0 – 6.3 A
- Operating voltage: 230 V ~ 50 Hz
- External control: 0 – 10 V
- Fuse: 5 mm × 20 mm, 6.3 A, 250 V, fast acting
- Max. ambient temperature: 35 °C
- Dimensions (W × H × D): 44 × 133 × 135 mm
- Weight: 0.55 kg
For the transport and protective packaging, environmentally friendly materials have been chosen that can be supplied to normal recycling. Ensure that plastic bags, packaging, etc. are properly disposed of. Do not just dispose of these materials with your normal household waste, but make sure that they are collected for recycling. Please follow the notes and markings on the packaging.
This product is subject to the European Waste Electrical and Electronic Equipment Directive (WEEE) in its currently valid version. Do not dispose of your old device with your normal household waste. Dispose of this product through an approved waste disposal firm or through your local waste facility. Comply with the rules and regulations that apply in your country. If in doubt, consult your local waste disposal facility.
report this adThomann GmbH
- Hans-Thomann-Straße 1
- 96138 Burgebrach
- www.thomann.de
- [email protected]
References
[xyz-ips snippet=”download-snippet”]