HDMI-SDI 3G Converter Full-HD
Quick Start GuideThis quick start guide contains important information on the safe operation of the product. Read and follow the safety advice and instructions given. Retain the quick start guide for future reference. If you pass the product on to others please include this quick start guide.
Safety instructions
Intended useThis device is used to convert HDMI signals to SDI format. Any other use or use under other operating conditions is considered to be improper and may result in personal injury or property damage. No liability will be assumed for damages resulting from improper use.Danger for children
Ensure that plastic bags, packaging, etc. are disposed of properly and are not within reach of babies and young children. Choking hazard! Ensure that children do not detach any small parts from the product. They could swallow the pieces and choke!
Where to use the productNever use the product
- in conditions of extreme temperature or humidity
- in extremely dusty or dirty areas
- in locations where the unit can become wet
- in locations with high levels of electrostatic or magnetic radiation
General handling
- To prevent damage, never use force when handling the product.
- Never immerse the product in water. Just wipe it with a clean dry cloth. Do not use liquid cleaners such as benzene, thinners or flammable cleaning agents.
Features
- Converter from HDMI to SDI signals with up to
- 3G-SDI connections
- Detects SD and HD formats automatically
- Connections:Input:HDMI type AOutput: 2 × SDI
- Impedance:75 ohms
- SDI formats:SD-SDI, HD-SDI, 3G-SDI
- Supported input resolutions: 480i @ 60 Hz, 576i @ 50 Hz, 720p @ 50 Hz,720p @ 60 Hz, 1080i @ 50 Hz, 1080i @ 60 Hz, 1080p @ 24 Hz / @ 25 Hz / @ 30 Hz /@ 50 Hz /@ 60 Hz
- Dimensions (W × H × D): 121 mm × 66 mm × 26 mm
- Weight: 0.25 kg
- Temperature range: 0 °C – 40 ° C, relative humidity 20 – 80 %, non-condensing
- Delivery including international power supply (5
V )
Operating elements
| 1. Connection for power supply2. Pilot light3. HDMI IN – HDMI input | 4. SDI OUT 1 – SDI output 15. SDI OUT 2 – SDI output 2 |
Using the product
- Connect the HDMI output of the desired device to the HDMI IN socket using a suitable HDMI
- Connect the input of a suitable SDI device to the SDI 1 output. If necessary, proceed in the same way with output SDI 2.
- Connect the device to a properly wired mains socket using the power supply supplied. The device is immediately ready for use.
- When the device is switched on, the power indicator lights up red.
- If the resolution of the input signal matches one of the supported resolutions of the SDI device connected to the output, the signal is output via the SDI 1 output and can be split for simultaneous output to a device connected to the SDI 2 output.
- When you have finished using the device, disconnect the power supply from the wall outlet.
For the transport and protective packaging, environmentally friendly materials have been chosen that can be supplied to normal recycling. Ensure that plastic bags, packaging, etc. are properly disposed of. Do not just dispose of these materials with your normal household waste, but make sure that they are collected for recycling. Please follow the notes and markings on the packaging.
This product is subject to the European Waste Electrical and Electronic Equipment Directive (WEEE) in its currently valid version. Do not dispose of your old device with your normal household waste. Dispose of this product through an approved waste disposal firm or through your local waste facility. Comply with the rules and regulations that apply in your country. If in doubt, consult your local waste disposal facility.
Technical specifications
| Resolutions | inputoutput | up to 1080p60 up to 1080p60 |
| Format change | yes | |
| Format | HDMI 1.4 | |
| HDCP | HDCP 1.4, SDI loop | |
| Colour depth | 12 bit | |
| Audio formats | DTS HD / Dolby TrueHD / LPCM7.1 / DTS / Dolby-AC3 / DSD | |
| Audio inputs | √. | |
| Audio outputs | √. | |
| Input connections | 1 × HDMI | |
| Output connections | 2 × SDI | |
| Signal looping | 1 ×SDI | |
| Power supply | External power adapter, 100 – 240 V~ 50/60 Hz | |
| Operating voltage | 5 V 1000 mA, centre positive |
|
| Degree of protection | IP20 | |
| Dimensions (W × H × D) | 121 mm × 66 mm × 26 mm | |
| Weight | 0.25 kg | |
| Ambient conditions | Temperature rangeRelative humidity0 °C…40 °C20 – 80 %, non-condensing |
Thomann GmbHHans-Thomann-Straße 196138 Burgebrachwww.thomann.de[email protected]DocID: 497001_26.02.2021
References
[xyz-ips snippet=”download-snippet”]