AuthenticationJetStream Switches1910012790 REV1.0.0
For Class A switch with power adapter:
FCC Compliance Information Statement
Product Name: JetStream SwitchModel Number: T1500G‑8T / TL‑SF1005LP / TL‑SF1005P / TL‑SF1008LP / TL‑SF1008P /TL‑SF1009P / TL‑SG1005LP / L‑SG1005P / TL‑SG1008P / TL‑SG116 / TL‑SG116E / TL‑SG1210P / TL‑SG2008P / TL‑SG2210P
|
Component Name |
Model |
| Power Adapter | T120100‑2B1 (For T1500G‑8T / TL‑SG116E / TL‑SG116) T535081‑2‑DT (For TL‑SG1005LP / TL‑SF1005LP / TL‑SF1008LP) T535131‑2‑DT (For TL‑SG2210P / TL‑SG1005P / TL‑SG1008P / TL‑SG1210P / TL‑SF1005P / TL‑SF1008P / TL‑SF1009P) T535135‑2‑DT (For TL‑SG2008P) |
Responsible party:TP‑Link USA Corporation, d/b/a TP‑Link North America, Inc.Address: 145 South State College Blvd. Suite 400, Brea, CA 92821Website: https://www.tp‑link.com/us/Tel: +1 626 333 0234Fax: +1 909 527 6803E‑mail: [email protected]‑link.comThis equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1) This device may not cause harmful interference.2) This device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.Product Name: Power AdapterModel Number: T120100‑2B1 / T535081‑2‑DT / T535131‑2‑DT / T535135‑2‑DTResponsible party:TP‑Link USA Corporation, d/b/a TP‑Link North America, Inc.Address: 145 South State College Blvd. Suite 400, Brea, CA 92821Website: https://www.tp‑link.com/us/Tel: +1 626 333 0234Fax: +1 909 527 6803E‑mail: [email protected]‑link.comThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:■ Reorient or relocate the receiving antenna.■ Increase the separation between the equipment and receiver.■ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.■ Consult the dealer or an experienced radio/ TV technician for help.This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:1) This device may not cause harmful interference.2) This device must accept any interference received, including interference that may cause undesired operation.Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.We, TP‑Link USA Corporation, have determined that the equipment shown as above has been shown to comply with the applicable technical standards, FCC part 15. There is no unauthorized change is made in the equipment and the equipment is properly maintained and operated. Issue Date: 2020/04/14
CE Mark Warning
This is a class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.TP‑Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of directives 2014/30/EU, 2014/35/EU, 2009/125/EC, 2011/65/EU, and (EU)2015/863.The original EU declaration of conformity may be found at https://www.tp‑link.com/en/ce
Canadian Compliance Statement
This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science, and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:(1) This device may not cause interference.(2) This device must accept any interference, including interference that may cause undesired operation of the device.
Safety Information
■ Keep the device away from water, fire, humidity, or hot environments.■ Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us.■ Do not use a damaged charger or USB cable to charge the device.■ Do not use any other chargers other than those recommended.■ The adapter shall be installed near the equipment and shall be easily accessible.■ Place the device with its bottom surface downward.Please read and follow the above safety information when operating the device. We cannot guarantee that no accidents or damage will occur due to improper use of the device. Please use this product with care and operate at your own risk.
Explanation of the symbols on the product labelNote: The product label can be found at the bottom of the product and its I.T.E. power supply.
|
Symbol |
Explanation |
 |
Class II equipment |
 |
AC voltage |
 |
DC voltage |
 |
Indoor use only. |
 |
Polarity of output terminals |
 |
Energy efficiency marking (Level VI) |
 |
RECYCLING
This product bears the selective sorting symbol for waste electrical and electronic equipment (WEEE). This means that this product must be handled pursuant to European directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment. The user has the choice to give his product to a competent recycling organization or to the retailer when he buys a new electrical or electronic equipment. |
Wall Mounting Requirements
For TL‑SG1210P:To mount the device on a wall, use 2 screws that comply with ANSI B1.1 4#, (5#), 6#, 8# standard, and are more than 7 mm in length. When the screws are fixed on the wall, the distance between the screw head and the wall should be more than 1.5 mm.For TL‑SF1005LP / TL‑SF1005P / TL‑SF1008LP / TL‑SF1008P / TL‑SF1009P / TL‑SG1005LP /TL‑SG1005P / TL‑SG1008P:To mount the device on a wall, use 2 screws that comply with ANSI B1.1 4#, (5#), 6#, 8# standard and are more than 8.5 mm in length. When the screws are fixed on the wall, the distance between the screw head and the wall should be more than 1.5 mm.Standard – DiameterANSI B1.1 #4 – 2.845 mmANSI B1.1 #5 – 3.175 mmANSI B1.1 #6 – 3.505 mmANSI B1.1 #8 – 4.166 mm
For Class A switch with no power adapter:FCC Compliance Information StatementProduct Name: JetStream SwitchModel Number: T1500‑28PCT / T1500G‑10MPS / T1600G‑18TS / T1600G‑28PS / T1600G‑28TS / T1600G‑52PS / T1600G‑52TS / T1700G‑28TQ / T1700X‑16TS / T2500G‑10TS / T2600G‑18TS / T2600G‑28MPS / T2600G‑28SQ / T2600G‑28TS / T2600G‑28TS‑DC / T2600G‑52TS / T2700G‑28TQ / T3700G‑28TQ / T3700G‑52TQ / TL‑SF1016 / TL‑SF1016DS / TL‑SF1024 / TL‑SF1024D / TL‑SF1048 / TL‑SG1008 / TL‑SG1008MP / TL‑SG1016 / TL‑SG1016D /TL‑SG1016DE / TL‑SG1016PE / TL‑SG1016S / TL‑SG1024 / TL‑SG1024D / TL‑SG1024DE /TL‑SG1024S / TL‑SG1048 / TL‑SG1218MPE / TL‑SG2210MP / TL‑SG2428P / TL‑SL1218MP /TL‑SL1226P / TL‑SL2428P / TL‑SL1218PResponsible party:TP‑Link USA Corporation, d/b/a TP‑Link North America, Inc.Address: 145 South State College Blvd. Suite 400, Brea, CA 92821Website: https://www.tp‑link.com/us/Tel: +1 626 333 0234Fax: +1 909 527 6803E‑mail: [email protected]‑link.comThis equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:1) This device may not cause harmful interference.2) This device must accept any interference received, including interference that may cause undesired operation.Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
We, TP-Link USA Corporation, have determined that the equipment shown as above has been shown to comply with the applicable technical standards, FCC part 15. There is no unauthorized change is made in the equipment and the equipment is properly maintained and operated.Issue Date: 2020/04/14
CE Mark Warning
This is a class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.TP‑Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of directives 2014/30/EU, 2014/35/EU, 2009/125/EC, 2011/65/EU, and (EU)2015/863.The original EU declaration of conformity may be found at https://www.tp‑link.com/en/ce
Canadian Compliance StatementThis device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science, and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:(1) This device may not cause interference.(2) This device must accept any interference, including interference that may cause undesired operation of the device.
Safety Information■ Keep the device away from water, fire, humidity or hot environments.■ Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us.■ Do not use any other chargers than those recommended.■ Place the device with its bottom surface downward.
Please read and follow the above safety information when operating the device. We cannot guarantee that no accidents or damage will occur due to improper use of the device. Please use this product with care and operate at your own risk.
Explanation of the symbols on the product labelNote: The product label can be found at the bottom of the product and its I.T.E. power supply.
|
Symbol |
Explanation |
|
Class II equipment |
|
AC voltage |
|
DC voltage |
|
Indoor use only. |
|
Polarity of output terminals |
|
Energy efficiency marking (Level VI) |
|
RECYCLING
This product bears the selective sorting symbol for waste electrical and electronic equipment (WEEE). This means that this product must be handled pursuant to European directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment. The user has the choice to give his product to a competent recycling organization or to the retailer when he buys a new electrical or electronic equipment. |
For Class B switch with power adapter:FCC Compliance Information Statement
Product Name: JetStream SwitchModel Number: TL‑SF1005D / TL‑SF1008D / TL‑SF1016D / TL‑SG1005D / TL‑SG105 / TL‑SG105E/ TL‑SG105S / TL‑SF1024M / TL‑SG1008D / TL‑SG108 / TL‑SG108E / TL‑SG108S / TL‑SG108PE / TL‑SG105PE
|
Component Name |
Model |
| Power Adapter | T050060‑2B1 (For TL‑SF1005D / TL‑SF1008D / TL‑SF1016D /TL‑SG1005D / TL‑SG105 / TL‑SG105E / TL‑SG105S) T090060‑2B1 (For TL‑SF1024M / TL‑SG1008D / TL‑SG108 /TL‑SG108E / TL‑SG108S) T480125‑2‑DT (For TL‑SG108PE) T535131‑2‑DT (For TL‑SG105PE) |
Responsible party:TP‑Link USA Corporation, d/b/a TP‑Link North America, Inc.Address: 145 South State College Blvd. Suite 400, Brea, CA 92821Website: https://www.tp‑link.com/us/Tel: +1 626 333 0234Fax: +1 909 527 6803E‑mail: [email protected]‑link.comThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:■ Reorient or relocate the receiving antenna.■ Increase the separation between the equipment and receiver.■ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.■ Consult the dealer or an experienced radio/ TV technician for help.This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:1) This device may not cause harmful interference.2) This device must accept any interference received, including interference that may cause undesired operation.Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.Product Name: Power AdapterModel Number: T050060‑2B1 / T090060‑2B1 / T480125‑2‑DT / T535131‑2‑DTResponsible party:TP‑Link USA Corporation, d/b/a TP‑Link North America, Inc.Address: 145 South State College Blvd. Suite 400, Brea, CA 92821Website: https://www.tp‑link.com/us/Tel: +1 626 333 0234Fax: +1 909 527 6803E‑mail: [email protected]‑link.comThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:■ Reorient or relocate the receiving antenna.■ Increase the separation between the equipment and receiver.■ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.■ Consult the dealer or an experienced radio/ TV technician for help.This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:1) This device may not cause harmful interference.2) This device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.We, TP‑Link USA Corporation, has determined that the equipment shown as above has been shown to comply with the applicable technical standards, FCC part 15. There is no unauthorized change is made in the equipment and the equipment is properly maintained and operated.Issue Date: 2020/04/14
CE Mark Warning
This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.TP‑Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of directives 2014/30/EU, 2014/35/EU, 2009/125/EC, 2011/65/EU, and (EU)2015/863.The original EU declaration of conformity may be found at https://www.tp‑link.com/en/ce
Canadian Compliance StatementThis device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science, and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:(1) This device may not cause interference.(2) This device must accept any interference, including interference that may cause undesired operation of the device.
Industry Canada StatementCAN ICES‑3 (B)/NMB‑3(B)
Safety Information■ Keep the device away from water, fire, humidity or hot environments.■ Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us.■ Do not use a damaged charger or USB cable to charge the device.■ Do not use any other chargers than those recommended.■ The adapter shall be installed near the equipment and shall be easily accessible.■ Place the device with its bottom surface downward. (For metal shell devices)
Use only power supplies which are provided by the manufacturer and in the original packing of this product. If you have any questions, please don’t hesitate to contact us. (For plastic shell devices)Please read and follow the above safety information when operating the device. We cannot guarantee that no accidents or damage will occur due to improper use of the device. Please use this product with care and operate at your own risk.
Explanation of the symbols on the product labelNote: The product label can be found at the bottom of the product and its I.T.E. power supply.
|
Symbol |
Explanation |
|
Class II equipment |
|
AC voltage |
|
DC voltage |
|
Indoor use only. |
|
Polarity of output terminals |
|
Energy efficiency marking (Level VI) |
|
RECYCLING
This product bears the selective sorting symbol for waste electrical and electronic equipment (WEEE). This means that this product must be handled pursuant to European directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment. The user has the choice to give his product to a competent recycling organization or to the retailer when he buys a new electrical or electronic equipment. |
Wall Mounting Requirements
For TL‑SG105E/Tl‑SG108E/TL‑SG108PE:To mount the device on a wall, use 2 screws that comply with ANSI B1.1 4#, (5#), 6# standard and are more than 7 mm in length. When the screws are fixed on the wall, the distance between the screw head and the wall should be more than 1.5 mm.
References
[xyz-ips snippet=”download-snippet”]