tp-link TL-WA1201 Wireless Gigabit Access Point Installation Guide

Table of Contents

Quick Installation GuideWireless Gigabit Access PointTL-WA1201

Configure the Access Point

Access Point Mode (Default) Transforms your existing wired network to a wireless one.

Connect the access point according to steps A to D in the diagram.
Turn on the power, and wait until the Wireless LEDsare lit and stable.
Use the default SSID and Password printed on the label of the access point to join its Wi-Fi network.
Launch a web browser and enter http://tplinkap.net. Create a password to log in.
Go to Quick Setup, select Access Point mode and click Next. Follow the step-by-step instructions to complete the configuration.
Now, reconnect your wireless devices to the new Wi-Fi network.

Enjoy!

Range Extender Mode Extends the range of an existing Wi-Fi network.

Connect the access point according to steps A to D in the diagram.
Turn on the power, and wait until the Wireless LEDsare lit and stable.
Use the default SSID and Password printed on the label of the access point to join its Wi-Fi network.
Launch a web browser and enter http://tplinkap.net. Create a password to log in.
Go to Quick Setup, select Access Point mode and click Next. Follow the step-by-step instructions to complete the configuration.
Relocate the access point to a suitable place. For details, refer to the tips below.
Now, connect your devices to the access point wirelessly or via an Ethernet cable.

Tips for Optimal Wireless Signal

Halfway is the best way.Generally, the ideal location for a repeater is about halfway between your wireless router and your wireless clients, and make sure that the location you choose is within the range of the host router. If that is not possible, place it closer to your wireless router to ensure stable performance.
Less obstacles ensure better performance.Choose a location with fewer obstacles around that may block the signal between the access point and the host network. An open corridor or a spacious location is ideal.
Less interference provides more stability.Choose a location away from Bluetooth devices and other household electronics, such as cordless phones, microwaves, and baby monitors to minimize signal interference.

Client Mode Connects your wired devices to a wireless network.

Connect the access point according to steps A to D in the diagram.
Turn on the power, and wait until the Wireless LEDsare lit and stable.
Use the default SSID and Password printed on the label of the access point to join its Wi-Fi network.
Launch a web browser and enter http://tplinkap.net. Create a password to log in.
Go to Quick Setup, select Client mode and click Next. Follow the step-by-stepinstructions to complete the configuration.
Now, connect your wired device to the access point via an Ethernet cable.

Multi-SSID Mode Creates multiple wireless networks to provide different security and VLAN groups.

Connect the access point according to steps A to D in the diagram.
Turn on the power, and wait until the Wireless LEDsare lit and stable.
Use the default SSID and Password printed on the label of the access point to join its Wi-Fi network.
Launch a web browser and enter http://tplinkap.net. Create a password to log in.
Go to Quick Setup, select Multi-SSID mode and click Next. Follow the step-by-step instructions to complete the configuration.
Go to Settings > Wireless > Wireless Settings to modify VLAN IDs.
Now, connect your wireless devices to the Wi-Fi networks isolated by VLANs.

Power on via the PoE Injector

Power the device with the included passive PoE injector when the access point is located far from a power outlet.Note: The passive PoE injector supports a cable length up to 30 meters, but the value may vary due to the environment.

Frequently Asked Questions (FAQ)

Q1. How do I restore the access point to its factory default settings?

With the access point powered on, use a pin to press and hold the Reset button until the Power LED starts blinking, then release the button.Note: Resetting the access point will clear all previous configurations, and the access point will reset to the default Access Point mode.

Q2. What should I do if I cannot access the web management page?

If the computer has a static IP address, change its settings to obtain an IP address automatically.
Verify that http://tplinkap.net or http://192.168.0.254 is correctly entered in the web browser.
Use another web browser and try again.
Reboot your access point and try again.
Power off your host AP and enter http://tplinkap.net in the web browser to try again.

Q3. How do I recover the access point’s web management password or retrieve my Wi-Fi password?

If you forget the password for the web management page, refer to Q1 to reset the access point to its factory default settings. Then create a new login password.
If you forget your Wi-Fi password, but are able to log in to the web management page, login and go to Settings > Wireless > Wireless Settings to retrieve or reset your Wi-Fi password.

Q4. What should I do if my wireless network is not stable?This could be caused by interference. You can try the following methods:

Log in to the web management page. Go to Settings > Wireless > Wireless Settings and change your wireless channel to a different one.
Move the access point to a new location away from Bluetooth devices and other household electronics, such as cordless phones, microwaves, and baby monitors to minimize signal interference.

Safety Information

Keep the device away from water, fire, humidity, or hot environments.
Do not attempt to disassemble, repair, or modify the device.
Do not use any other chargers other than those recommended.
Do not use a damaged charger or USB cable to charge the device.
Do not use the device where wireless devices are not allowed.
Adapter shall be installed near the equipment and shall be easily accessible.Please read and follow the above safety information when operating the device. We cannot guarantee that no accidents or damage will occur due to improper use of the device. Please use this product with care and operate at your own risk.

For technical support, the user guide, and other information, please visit https://www.tp-link.com/support, or simply scan the QR code.