Travis 564 Electric Fireplace/Insert User Manual

Travis 564 Electric Fireplace/Insert User Manual

Read these instructions completely before beginning installation. Failure to follow them could cause a heater malfunction and result in serious injury and/or property damage.

WARNING: All electric heaters have hot or sparking parts inside. Do not use it in areas where gasoline, paint or flammable liquids are stored.

WARNING: This fireplace is tested and listed for use only with the optional accessories listed in these instructions. Use of optional accessories not specifically tested for this heater could void the heater warranty and/or result in a safety hazard.

Keep this manual for future reference.

SAFETY INFORMATION

Due to high temperatures, the fireplace should be located out of traffic and away from furniture and draperies.

Do not place clothing or other flammable material on or near the insert. Never place any objects on the insert.

The insert can become very hot when running. Keep children and adults away from hot surfaces to avoid burns or clothing ignition. The insert will remain hot for a time after shutdown. Allow surfaces to cool before touching.

When using electrical heaters, basic precautions, like the ones listed below, should always be followed in order to reduce the risk of fire, electric shock and injury.

  1. Read all instructions before using this heater.
  2. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes and curtains at least 3 feet from the front of the heater; keep them away from sides and rear as well.
  3. Always unplug heater when it’s not in use.
  4. Do not operate the fireplace if it has a damaged cord or plug, after it has malfunctioned, or if the unit has been dropped or damaged in any way.
  5. Do not use the heater outdoors.
  6. This heater is not intended for use in bathrooms, laundry areas and similar indoor locations. Never place the heater where it may fall into a bathtub or other water containers.
  7. Do not run the cord under carpeting. Do not cover the cord with throw rugs, runners or anything else. Arrange the cord away from traffic areas where it could be tripped over.
  8. To disconnect the heater, turn the controls to “OFF” before removing the plug from the outlet.
  9. Do not insert or allow foreign objects to enter any ventilation or exhaust opening, as this may cause an electric shock, fire or damage to the heater.
  10. To prevent a possible fire, do not block air intakes in any manner.
  11. A heater has hot or sparking parts inside. Do not use it in areas where gasoline, paint or flammable liquids are used or stored.
  12. Use this heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock or injury to persons.
  13. Avoid the use of an extension cord because the extension cord may overheat and cause a fire. If you have to use an extension cord, the cord should be No. 14 AWG minimum size and rated not less than 1875 WATTS.
  14. Always use a properly grounded, protected (fuse or circuit breaker), and polarized outlet.
  15. Always use ground fault protection where it is required by electrical codes.
  16. Always disconnect the power before performing any cleaning, maintenance or relocation of the heater.
  17. To prevent a possible fire, do not burn wood or other materials in this heater.
  18. To prevent electric shock or fire, always use a certified electrician, should new circuits or outlets be required.
  19. When transporting or storing the heater, keep it in a dry place, free from excessive vibration.

LISTING APPROVALS

This heater has been tested in accordance with the CSA Standards for fixed and location-dedicated electric room heaters in the United States. All components are UL or CSA safety certified.

  • Voltage: 120 AC,
  • Hz: 60
  • Watts: 1500
  • Amps: 15

Note: This heater must be electrically wired and grounded in accordance with local codes or, in the absence of local codes, with National Electric Code.

Dimensions

LOCATING THE FIREPLACE INSERT

WARNING: Never locate this heater where it may fall into a bathtub or any water container.

NOTICE: All clearances must be maintained to combustibles. Illustrations throughout these instructions reflect typical installations and are for design purposes only. Actual installations may vary slightly due to individual preferences.

Heater must be placed so it remains level (use included level to verify). Leveling bolts are provided on the base of the fireplace to insure proper leveling.

WARNING: RISK OF FIRE. MAINTAIN ALL SPECIFIED CLEARANCES TO COMBUSTIBLES. FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY CAUSE A FIRE OR CAUSE THE APPLIANCE TO OVERHEAT. ENSURE ALL CLEARANCES (I.E. BACK, SIDE, TOP, VENT MANTEL, FRONT, ETC.) ARE CLEARLY MAINTAINED. APPLIANCE GRILLS (VENTS) LOCATED ON THE FRONT AND BACK OF THIS ELECTRIC APPLIANCE CANNOT IN ANY WAY BE COVERED AS IT MAY CREATE A FIRE HAZARD.

WHEN USING PAINT OR LACQUER TO FINISH THE AREA ABOVE THE FIREPLACE, THE PAINT OR LACQUER MUST BE HEAT RESISTANT TO PREVENT DISCOLORATION.

Proposition 65 Warning: Fuels used in gas, woodburning or oil fired appliances, and the products of combustion of such fuels, contain chemicals known to the State of California to cause cancer, birth defects and other reproductive harm. California Health & Safety Code Sec. 25249.6

SECURING THE INSERT WHEN USING HEAVY FACES

When using a heavy face with this fireplace (e.g. Artisan Face), you may wish to secure the fireplace to the framing or floor to prevent it from tilting forward. This is especially important if the fireplace is raised above the hearth.

Recommendations for Framed-In Applications

If this appliance is framed in, we recommend using plumbing straps or brackets to secure the front of the fireplace to the drywall and/or framing. Secure the straps to the side or upper flanges on the fireplace (do not screw into the fireplace). Secure the strap in a location where it will be concealed by the face. This allows the straps to be disconnected if the appliance needs to be removed from the framing.

Recommendations for Insert Applications

If the appliance is placed inside a fireplace (a.k.a. “insert”), we recommend using brackets to secure the fireplace to the base of the fireplace. Remove one of the screws on the back or side of the fireplace and secure the appliance to the floor using plumbing straps or brackets.

FRAMING DIMENSIONS WHEN BUILT IN

NOTE: Make sure the opening for the framing is constructed to the dimensions listed above (31-7/8” wide by 26-3/4” tall). This ensures the face properly conceals the opening at the same time allowing the fireplace to insert into the cavity.

When installing the fireplace, take care when routing the power cord. You may wish to allow for additional space behind the framing for power cord access.

CLEARANCES WHEN BUILT-IN

The fireplace insert may be placed within a framed enclosure that is level, dry, and capable of supporting the weight of the appliance and front glass. It may be placed directly on wood or a non-combustible surface (not on linoleum or carpet).

INSTALLATION

CAUTION: The unit’s power supply cord must be connected to a properly grounded and protected 120-volt outlet. Always use ground fault protection where required by the electrical code.

WARNING – RISK OF FIRE! To prevent a possible fire, do not block the grills, louvers, or air openings on the fireplace insert in any manner.

WARNING – RISK OF FIRE! The power cord must not be pinched or placed against a sharp edge. Secure the cord to avoid tripping or snagging thus reducing the risk of fire, electric shock or personal injury. Do not run the cord under carpeting. Do not cover the cord with throw rugs, runners or similar items. Arrange the cord away from traffic areas where it could be tripped over.

Select a suitable location that is not susceptible to moisture and is away from drapes, furniture and high traffic areas.Note: Follow all national and local electrical codes.

INSTALLATION OVERVIEW – MASONRY FIREPLACES

INSTALLATION OVERVIEW – ZERO-CLEARANCE (METAL) FIREPLACES

OPTIONAL DECORATIVE INTERIORS

This insert is shipped with an under-lit log pre-installed. Glowing embers are also included with the fireplace insert if you want a different appearance.

Glowing Embers

Removing The Log

The under-lit log is shipped in place. On newer units, the log has tabs on each side that hold it in place. Remove the black interior side panel (or carefully remove the tabs) to remove the log set. This is done by removing the two screws holding the panel in place.

Installing the Glowing Embers

Pour the glowing embers onto the tray as shown below. Feel free to use the combination of glowing embers you find most appealing.

FACE BRACKET INSTALLATION

This fireplace includes brackets to attach the 564 faces listed below to the front of the fireplace. Two sets of brackets are included to accommodate the different faces. See the list of faces below to identify the correct brackets. Use the nuts included with the face kits to attach the brackets.

FACE ATTACHMENT

With the fireplace in place, attach the face to the fireplace as shown below.

OPERATING INSTRUCTIONS

REMOVING THE SURROUND GLASS

Before removing the surround glass, make sure to have a suitable location to place the surround glass once it is removed. Do not place the glass on sharp or uneven areas that may chip or damage the tempered glass. Use both hands to lift the surround glass directly up. The hooks on the glass will disengage from the pins that protrude from the side of the insert.

REMOTE CONTROL OPERATION

  1. For the remote to function make sure the heater is plugged in and main power switch is turned on. Note: The remote control requires 2 AA batteries.Note: The heater may release a slight odor the first time it is turned on. This is normal. The heating elements inside the heater will burn off any accumulated oils or dust during initial heating. This may also occur when dust accumulates on the heating elements over periods of non-use.
  2. When operating the remote make sure to point the remote at the center of the fireplace insert. Each time you press a button on the remote the LED indicator on the top right of the remote should blink and the fireplace insert will “BEEP”. If the LED fails to blink check the batteries. It takes up to one second for the fireplace insert to respond to the transmitter. DO NOT PRESS THE BUTTONS MORE THAN ONCE within two seconds. This allows the fireplace insert to respond to the remote.
  3. Power on button: The power – on button at top left corner of the remote is the main ON/ OFF power button. This will turn off all the functions (heater and display). If you turn the fireplace insert OFF, then ON, the fireplace insert will return to its last heater and display settings.
  4. Flame Power On button ” DISPLAY ON OFF”: This button controls both the ember and flame effect. Once the flame effect is ON use the + and – buttons as explained below to adjust the flame brightness as desired. Press this button again to turn OFF the flame effect.
    • The – or + buttons control the brightness of EMBER.To increase the brightness of ember bed, press and release the + button. Each time you press this button the brightness will increase small amount, until the maximum is reached.To decrease the brightness of ember bed, press and release the – button. Each time you press this button the brightness will decrease a small amount, until the minimum brightness is reached.
    • The FLAME INTENSITY– or + buttons control the brightness of FLAME.To increase the brightness / flame Intensity , , press and release the + button. Each time you press this button the brightness will increase by a small amount, until the maximum is reached.To decrease the brightness / flame Intensity , , press and release the – button . Each time you press this button the brightness will decrease by small amount, until the minimum brightness is reached. You can mix theember and the flame to create a realistic flame effect.
  5. Heater “On/Off” button: Press this button to turn the heater ON. The heater will always start at high heat setting 1500W. To turn the heater off press this button again.HIGH button: Press the high button to switch the heater to high heat setting 1500W.LOW button: Press the low button to switch the heater to LOW heat setting 750W.TEMP button: Press the TEMP. button to switch the heater to AUTO mode. See page 15 for details.
  6. To turn off the heater unit completely press the button once.

Note: The remote control must be within about 20 feet (6 meters) of the fireplace insert and not too far off to either side.

Important! If the flame does not activate after the POWER ON/OFF button is pressed, press the DISPLAY ON/OFF button to activate the flame. If the flame does not appear, press the POWER ON/OFF button again.

WARNING: Before undertaking maintenance unplug the fireplace insert.

DIRECT OPERATION

Plug the heater into a suitable outlet.

  1. “Power ON/OFF”Set this switch to position I to turn the product ON. Setting it to O to turn the product OFF. The POWER LED will be lit when the fireplace insert is on.
  2. “Heat control button”Press the HEAT button repeatedly to set the heater to the desired heat set. The HEATER LED will indicate the current setting for the heater as shown below:HEATER LED = Red = 1500W HEAT OUTPUTHEATER LED = Blue = 750W HEAT OUTPUTHEATER LED = Purple = AUTO MODE Auto ModeIn this mode the heater will automatically turn on and off. When the room temperature drops below 71° F (22° C) the heater will turn on to the high heat setting (1500 watt). When the room temperature is between 71° and 77° F (22-25° C) the heater output will switch to the low heat setting (750W). When the room temperature goes above 77° F (25° C) the heater will turn off.
  3. “Flame control button”Press “Flame” button to adjust the flame intensity and ember bed brightness.Press the “FLAME” control button to cycle through LO, MED, HI and OFF.

CLEANING AND MAINTENANCE

WARNING: Always disconnect the power and allow the heater to cool before performing any cleaning, maintenance or relocation. Turn the controls to OFF and remove the plug from the outlet or turn off the circuit breaker before attempting any cleaning.

FRONT GLASS

  1. Remove dust by buffing lightly with a clean dry cloth.
  2. To remove fingerprints or other marks, the glass can be cleaned with a damp cloth using a good quality household glass cleaner. The glass should be completely dried with a lint free cloth or paper towel.
  3. In the event of glass breakage, vacuum all remaining glass pieces with a shop vac. DO NOT VACUUM WHILE THE PIECES ARE HOT. Replace glass only with replacement parts made specifically for this heater. Never substitute material.

REPLACEMENT PARTS

TROUBLE SHOOTING

WARNING: Always disconnect power and allow the heater to cool before performing any cleaning, maintenance or relocation. Turn the controls to OFF and remove the plug from the outlet or turn off the circuit breaker before attempting any cleaning.

1 YEAR LIMITED WARRANTY

Register your TRAVIS INDUSTRIES, INC. Limited 1 Year Warranty online at traviswarranty.com. TRAVIS INDUSTRIES, INC. warrants this electric appliance (appliance is defined as the equipment manufactured by TRAVIS INDUSTRIES,INC.) to be defect-free in material and workmanship to the original purchaser from the date of purchase as follows:Check with your dealer in advance for any costs to you when arranging a warranty call.Mileage or service charges are not covered by this warranty. This charge can vary from store to store.

CONDITIONS & EXCLUSIONS
  1. This new electric appliance must be installed by a TRAVIS INDUSTRIES, INC. dealer or a qualified electrician. It must be installed, operated, and maintained at all times in accordance with the instructions in the Owner’s Manual. Any alteration, willful abuse, accident, neglect, or misuse of the product shall nullify this warranty.
  2. This warranty is nontransferable, and is made to the ORIGINAL purchaser, provided that the purchase was made through an authorized TRAVIS dealer.
  3. Discoloration and some minor expansion, contraction, or movement of certain parts and resulting noise, is normal and not a defect and, therefore, not covered under warranty. The installer must ensure the appliance is operating per the instructions at the time of installation.
  4. Travis Industries will not be responsible for inadequate performance caused by environmental conditions such as mechanical systems such as furnaces, fans, clothes dryers, etc.
  5. This Warranty is void if:a. The unit has been operated in atmospheres contaminated by chlorine, fluorine or other damaging chemicals.b. The unit is subject to submersion in water or prolonged periods of dampness or condensation.c. Any damage to the unit due to water, or weather damage.
  6. Exclusions to this 1 Year Warranty include: injury, loss of use, damage, failure to function due to accident, negligence, misuse, improper installation, alteration or adjustment of the manufacturer’s settings of components, lack of proper and regular maintenance, damage incurred while the appliance is in transit, alteration, or act of God.
  7. This 1 Year warranty excludes damage caused by normal wear and tear, such as paint discoloration or chipping, worn or torn wiring, etc. Also excluded is damage to the unit caused by abuse, improper installation, modification of the unit.
  8. Damage to the reflective surfaces (i.e. mirror) caused by fingerprints, scratches, melted items, or other external sources from the use of cleaners other than mild soap and water is not covered in this warranty.
  9. TRAVIS INDUSTRIES, INC. is free of liability for any damages caused by the appliance, as well as inconvenience expenses and materials. Incidental or consequential damages are not covered by this warranty. In some states, the exclusion of incidental or consequential damage may not apply.
  10. This warranty does not cover any loss or damage incurred by the use or removal of any component or apparatus to or from the electric appliance without the express written permission of TRAVIS INDUSTRIES, INC. and bearing a TRAVIS INDUSTRIES, INC. label of approval.
  11. Any statement or representation of TRAVIS products and their performance contained in TRAVIS advertising, packaging literature, or printed material is not part of this 1 year warranty.
  12. This warranty is automatically voided if the appliance’s serial number has been removed or altered in any way. If the appliance is used for commercial purposes, it is excluded from this warranty.
  13. No dealer, distributor, or similar person has the authority to represent or warrant TRAVIS products beyond the terms contained within this warranty. TRAVIS INDUSTRIES, INC. assumes no liability for such warranties or representations.
  14. TRAVIS INDUSTRIES,INC. will not cover the cost of the removal or re-installation of hearths, facing, mantels, or other components .
  15. If for any reason any section of this warranty is declared invalid, the balance of the warranty remains in effect and all other clauses shall remain in effect.
  16. THIS 1 YEAR WARRANTY IS THE ONLY WARRANTY SUPPLIED BY TRAVIS INDUSTRIES, INC., THE MANUFACTURER OF THE APPLIANCE. ALL OTHER WARRANTIES, WHETHER EXPRESS OR IMPLIED, ARE HEREBY EXPRESSLY DISCLAIMED AND PURCHASER’S RECOURSE IS EXPRESSLY LIMITED TO THE WARRANTIES SET FORTH HEREIN.
IF WARRANTY SERVICE IS NEEDED:
  1. If you discover a problem that you believe is covered by this warranty, you MUST REPORT it to your TRAVIS dealer WITHIN 30 DAYS, giving them proof of purchase, the purchase date, and the model name and serial number.
  2. If your dealer is unable to repair your appliance’s defect , he may process a warranty claim through TRAVIS INDUSTRIES, INC., including the name of the dealership where you purchased the appliance, a copy of your receipt showing the date of the appliance’s purchase, and the serial number on your appliance. At that time, you may be asked to ship your appliance, freight charges prepaid, to TRAVIS INDUSTRIES, INC. TRAVIS INDUSTRIES, INC., at its option, will repair or replace, free of charge, your TRAVIS appliance if it is found to be defective in material or workmanship within the time frame stated within this 1 year warranty. TRAVIS INDUSTRIES, INC. will return your appliance, freight charges (90 days) prepaid by TRAVIS INDUSTRIES, INC., to your regional distributor, or dealership.
  3. Check with your dealer in advance for any costs to you when arranging a warranty call. Mileage or service charges are not covered by this warranty. This charge can vary from store to store.

Travis 564 Electric Fireplace/Insert User Manual – Travis 564 Electric Fireplace/Insert User Manual –

[xyz-ips snippet=”download-snippet”]


Posted

in

by