Trendnet
1. Before You Start
1. Before You StartPackage Contents
- TI-IG30/TI-IG60
- Quick Installation Guide
- Removable terminal block
- DIN-rail mount
- Wall mount kit
Minimum Requirements
- Y Existing network
- Y Power Supply (TI-S12048)
2. Quick Reference
3. Hardware Installation
The PoE+ injector can be placed on a desktop, wall, or mounted to a DIN-Rail.DIN-rail Mounting Instructions1. Attach the DIN-Rail mount to the PoE+ injector.
2. Position the unit in front of the DIN-Rail and hook the mount bracket over the top of the rail.3. Rotate the fiber converter downward towards the rail to lock it into place. You will know it is secure when you hear the click.
4. To remove the unit, pull down to clear the bottom of the DIN-Rail and rotate up, away from the rail.
Wall Mounting Instructions
- Attach the wall mount plates to the PoE+ injector.
- Mount the switch.
Safety Note
- Turn off the power before connecting any module or wire. The correct power supply voltage (48 – 56 V DC) is listed on the product label. Check the voltage of your power source to make sure that you are using the correct part. Do NOT use voltage greater than 48 – 56 V DC, the product label.
- Calculate the maximum possible current in each power wire and common wire. Observe all electrical codes dictating the maximum current allowable for each wire size. If the current surpasses the maximum ratings, the wiring could overheat, causing serious damage to your equipment.
Applying Power
1. Connect the power supply (sold separately) to the included terminal block (as shown below) and secure it with the screws.Note: Polarities must match.2. Attach the terminal block to the unit, connect the neutral wire to the ground, and supply power to the power adapter.
3. Connect a network source and devices to the switch. Check the LEDs to confirm the connections are established. Your installation is completed.
4. Additional information
DIP Switch (TI-IG60 ONLY)
Declaration of ConformityManufacturer’s Name and AddressTRENDnet, Inc.
20675 Manhattan PlaceTorrance, CA 90501 USA
Product Information:Model Number: TI-IG30 / TI-IG60Product Name: Hardened Industrial 30 Watt Gigabit PoE+ InjectorHardened Industrial 60 Watt Gigabit PoE+ InjectorTrade Name: TRENDnet
TRENDnet hereby declares that the product is in compliance with the essential requirements and other relevant provisions under our sole responsibility.
Safety EN 60950-1: 2006 + A11: 2009 + A1: 2010 + A12: 2011 + A2: 2013
EMC EN 55022: 2010 + AC: 2011 Class A AS/NZS CISPR 22: 2009 + A1:2010 Class A EN 55024: 2010 CISPR 22: 2008 + Is1: 2009 + IS2: 2010 + Corr: 2012 Class A
This product is herewith confirmed to comply with the Directives.Directives: Low Voltage Directive 2006/95/ECEMC Directive 2004/108/ECRoHS Directive 2011/65/EUREACH Regulation (EC) No. 1907/2006
A person is responsible for this declaration.Place of Issue: Torrance, California, USAName: Sonny Su Signature:
Date: August 2, 2015Title: Director of Technology
Limited WarrantyTRENDnet warrants its products against defects in material and workmanship, under normal use and service. Specific warranty periods are listed on each of the respective product pages on the TRENDnet website.
CertificationsThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference.(2) This device must accept any interference received.Including interference that may cause undesired operation.
Waste electrical and electronic products must not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or Retailer for recycling advice.
Applies to PoE Products Only: This product is to be connected only to PoE networks without routing to the outside plant.
Note The Manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.
Advertencia En todos nuestros equipos se mencionan claramente las caracteristicas del adaptador de alimentacón necesario para su funcionamiento. El uso de un adaptador distinto al mencionado puede producir daños fisicos y/o daños al equipo conectado. El adaptador de alimentación debe operar con voltaje y frecuencia de la energia electrica domiciliaria exitente en el pais o zona de instalación.
Technical SupportIf you have any questions regarding the product installation, please contact our Technical Support. Toll-free US/Canada: 1-866-845-3673 Regional phone numbers available at www.trendnet.com/support
TRENDnet20675 Manhattan PlaceTorrance, CA 90501USAProduct Warranty RegistrationPlease take a moment to register your product online. Go to TRENDnet’s website at: www.trendnet.com/registerCopyright © 2015. All Rights Reserved. TRENDnet.TI-IG30/TI-IG60(V1) /09.08.2015
References
[xyz-ips snippet=”download-snippet”]