TRENDNET TI-F10SC/TI-F10S30 Installation Guide

TRENDNET TI-F10SC/TI-F10S30 Installation Guide

1. Before You Start

Package Contents

  • TI-F10SC/TI-F10S30
  •  Quick Installation Guide
  •  Removable terminal block
  • DIN-Rail mount
  •  Wall mount plates

Minimum Requirements

  • Existing network
  • Power Supply (TI-M6024)

2. Quick Reference

3. Hardware Installation

The fiber converter can be placed on a desktop, wall, or mounted to aDIN-Rail. DIN-rail Mounting Instructions

  1. Attach the DIN-Rail mount to the fiber converter.
  2. Position the unit in front of the DIN-Rail and hook the mount bracket over the top of the rail.
  3. Rotate the fiber converter downward towards the rail to lock it into place. You will know it is secure when you hear the click.  Mounting the unit              Releasing the unit
  4. To remove the unit, pull down to clear the bottom of the DIN-Rail and rotate away from the rail.

Wall Mounting Instructions

  1.  Attach the wall mount plates to the fiber converter.
  2. Mount the unit.

Safety Note

  • Turn off the power before connecting any module or wire. The correct power supply voltage (12 – 60 V DC or 18 – 36 V AC) is listed on the product label. Check the voltage of your power source to make sure that you are using the correct part. Do NOT use voltage greater than 12 – 60 V DC or 18 – 36 V AC, the product label.
  • Calculate the maximum possible current in each power wire and common wire. Observe all electrical codes dictating the maximum current allowable for each wire size. If the current surpasses the maximum ratings, the wiring could overheat, causing serious damage to your equipment.

Applying Power

  1. Connect the power supply (sold separately) to the included terminal block (as shown below) and secure with the screws.Note: Polarities must match.
  2. Attach the terminal block to the unit, connect the neutral wire to the ground, and supply power to the power adapter.
  3. Connect a network source and devices to the switch. Check the LEDs to confirm the connections are established. Your installation is completed.

4. Additional information

DIP Switch

  Dip 1   ON   Converter mode
 OFF   Switch mode (default)
  Dip 2   ON   LFP function enabled
  OFF   LFP function disabled (default)

Note: LFP stands for Link Fault Pass Through. If the transmitting media converter experiences TP link loss, it will disconnect transmission. Thereceiving fiber converter will also disconnect.

Manufacturer’s Name and Address

TRENDnet, Inc. 20675 Manhattan PlaceTorrance, CA 90501 USA

Product Information:

Product Name:  TI-F10SC / TI-F10S30Model Number:   Hardened Industrial 100Base-FX Multi-Mode SC Fiber Converter (2 km, 1.2 mi.) Hardened Industrial 100Base-FX Single-Mode SC Fiber Converter (30 km, 18.6 mi.)

Trade Name:  TRENDnet

TRENDnet hereby declare that the product is in compliance with the essential requirements andother relevant provisions under our sole responsibility

Safety   EN 60950-1: 2006 + A11: 2009 + A1: 2010 + A12: 2011 + A2: 2013EMCEN 55011: 2009 + A1: 2010 Class AEN 55022: 2010 + AC: 2011 Class AEN 61000-6-4: 2007 + A1: 2011EN 55024: 2010EN 61000-6-2: 2005 + AC: 2005

Directives:Low Voltage Directive 2006/95/ECEMC Directive 2004/108/ECRoHS Directive 2011/65/EUREACH Regulation (EC) No. 1907/2006

Limited Warranty

TRENDnet warrants its products against defects in material and workmanship, under normal use andservice. Specific warranty periods are listed on each of the respective product pages on the TRENDnet website.

Certifications

This device complies with Part 15 of the FCCRules. Operation is subject to the following twoconditions:

  1. This device may not cause harmful interference.
  2. This device must accept any interference received. Including interference that may cause undesired operation.

Applies to PoE Products Only: This product is to be connected only to PoE networks without routing to the outside plant.

Note

The Manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.

If you have any questions regarding the product installation, please contact our Technical Support. Toll free US/Canada: 1-866-845-3673Regional phone numbers available at www.trendnet.com/support

TREND

net 20675 Manhattan Place Torrance, CA 90501 USA

Read More About This Manual & Download PDF:

References

[xyz-ips snippet=”download-snippet”]

Posted

in

by

admin

Tags:

, ,