ULINE H-2930 Econodot Dispenser Instruction Manual

ULINE H-2930 Econodot Dispenser

SPECIFICATIONS

SAFETY

The EconoDot® is an economical bench-top machine exclusively designed to dispense Glue Dots® Adhesive Products in rolls of up to 8,000 adhesive patterns. These instructions show the basic operation of the EconoDot including set up, loading and operation. For your safety it is important to read and understand these instructions before using the EconoDot. It is important to keep hands, hair, clothing, jewelry and other loose objects away from any moving parts during operation of this machine. The EconoDot is designed to exclusively dispense patented Glue Dots Adhesive Products on registered liner. Operating this machine outside of its intended nature will result in poor results, damage to the machine or compromised operator safety. Glue Dots International will not be held liable for any damage to products or persons resulting from improper use of the EconoDot.

IMPORTANT: Only persons who have read these instructions and who are familiar with the proper use of the EconoDot should operate this machine. All electrical work performed on the EconoDot should be performed by a licensed electrician or trained person supervised by a licensed electrician. Draw-in or squeezing can occur between the motor-driven and clamp rollers.

OPERATION

The EconoDot is designed to automatically dispense Glue Dots or Glue Lines, one at a time. The EconoDot can dispense stock 1/4″, 3/8″ and 1/2″ diameter GlueDots in all standard tack levels and profiles. It can also dispense 1″ Glue Lines and other custom products which fall within the registration marks. No programming is required with the EconoDot. The EconoDot is not intended to apply other adhesive types and should be operated indoors.IMPORTANT: Altering the EconoDot and its controls from its original manufactured state, nullifies its CE standards compatibility.IMPORTANT: Before starting any job, it is important you test various Glue Dots to determine the proper adhesive pattern, size, tack level and profile. Product samples for testing can be obtained by calling a ULINE Parts Specialist at 1-800-295-5510.

OPERATION AND LOADING INSTRUCTIONS

TO OPERATE THE ECONODOT

1. Plug the electrical cord into the back of the machine and then into a wall outlet.
2. Load a roll of Glue Dots products and thread the liner so a single adhesive pattern comes to rest on the nose plate. (See Figure 2)
3. Turn on the power using the power button located on the top of the control box.
4. Press the item to be adhered firmly against the adhesive pattern resting on the nose plate, peeling the item off the liner towards the supply reel. (See Figure 1)IMPORTANT: Lifting an adhesive pattern directly up off the liner or in a direction away from the supply reel may result in pulling excess liner from the supply reel or tearing of the liner. Avoid touching Glue Dots Adhesives as dust and oils will compromise the bond.
5. When the item to be adhered is pressed to the nose plate and covers the beam on the photo sensing eye a signal is sent to the machine that the adhesive pattern is being removed. Once the item is removed from the nose plate, uncovering the beam, the motor automatically advances the next adhesive pattern.IMPORTANT: The photo sensing eye’s beam must be covered then uncovered to ensure the advancement of the Glue Dots Adhesives.
6. Repeat application instructions.
7. The EconoDot has a built-in counter that displays the number of adhesive patterns used. To reset the counter push the reset button located on top of the control box and hold for 2 seconds.

TO LOAD THE ECONODOT

1. Loosen supply reel clamp knob located in front of the supply reel plate. Remove the plate by turning it clockwise and pulling it straight off the spindle. (See Figure 2)
2. Load the Glue Dots roll onto the supply reel, ensuring the liner runs in a clockwise direction. For 3/4″ wide rolls, place the supply reel with pads facing inward. For 1″ wide rolls, place the supply reel with pads facing outward.
3. Replace the supply reel plate. Tighten the supply reel clamp knob.
4. Pull the liner over the first roller, under the second roller, up through the U-channel sensor and over the nose plate.
5. Press down on the peeler roller separation lever located to the left and beneath the peeler rollers in order to create space between the two rollers. Thread the liner between the separated rollers.
6. Open the hinged door located on the side of the shroud and continue to thread the liner downward through the slit on the top of the shroud.
7. Press down on the spring-loaded lever located to the right of the motor-driven and clamp rollers in order to create space between the two rollers. Thread the liner between the two rollers. Release the spring loaded lever so the motor-driven and clamp rollers sandwich the liner. Close the door on the shroud. (Shroud door must be closed to operate the machine.)
8. Pull on the liner until a single adhesive pattern comes to rest on the nose plate.
9. Spent liner should trail into a trash receptacle.

MAINTENANCE/REPAIRS

All maintenance and repairs should be performed by a technical staff member such as a technician, electrician, maintenance personnel or equivalent. Maintenance performed by unqualified persons nullifies the EconoDot warranty.It is important to keep the sensors free from debris. Malfunctions not addressed in the troubleshooting section of these instructions can be directed to the Repairs Department at ULINE.

TROUBLESHOOTING

The following chart outlines problems that could arise while using the EconoDot. Malfunctions experienced outside of the issues outlined below will need to be addressed by an experienced, professional technician or electrician.

1-800-295-5510uline.com

References

• 
  ULINE – Shipping Boxes, Shipping Supplies, Packaging Materials, Packing Supplies
• 
  Uline.ca – Shipping Boxes, Shipping Supplies, Packaging Materials, Packing Supplies
• 
  Uline.mx – Cajas para Envíos, Materiales de Empaque, Materiales de Empaque, Suministros para Empaque