V-TAC LED SOLAR LIGHT Instruction Manual

V-TAC LED SOLAR LIGHT

TECHNICAL SPECIFICATIONS

DIMENSIONS

INTRODUCTION & WARRANTY

Thank you for selecting and buying V-TAC product. V-TAC will serve you the best. Please read these instructions carefully before starting the installation and keep this manual handy for future reference. If you have any another query, please contact our dealer or local vendor from whom you have purchased the product. They are trained and ready to serve you at the best. The warranty is valid for 3 years from the date of purchase. The warranty does not apply to damage caused by incorrect installation or abnormal wear and tear. The company gives no warranty against damage to any surface due to incorrect removal and installation of the product.

WARNING!

1. The light source of this luminaire is not replaceable; when the light source reaches its end of life the whole luminaire shall be replaced.
2. Installation should be done by certified electrician.

 This marking indicates that this product should not be disposed of with other household wastes

MULTI-LANGUAGE MANUAL QR CODEPlease scan the QR code to access the manual in multiple languages.

IN CASE OF ANY QUERY/ISSUE WITH THE PRODUCT, PLEASE REACH OUT TO US AT: [email protected] FOR MORE PRODUCTS RANGE, INQUIRY PLEASE CONTACT OUR DISTRIBUTOR OR NEAREST DEALERS.V-TAC EUROPE LTD. BULGARIA, PLOVDIV 4000, BUL.L.KARAVELOW 9B

INSTALLATION DIAGRAM

Installation Instruction:

1. Drill two holes on the wall after confirming the installation position, then install the expansion plug into the holes.
2. Put the screw into the expansion plug, do not screw to the end, it is ok if the screw head is about 2-3mm away from the wall. If the installation surface is wood or soft material, it can be screwed directly without using the expansion plug.
3. Put the mounting base into two screws on the wall. Then, tighten the base as shown in Figure 1.
4. Install the lamp on the base, and it can be used.

Switch Function:– Press and hold the button for 2-3 seconds to switch ON the solar light. Once switched ON it will indicate a blue light.– When switching on the solar light by default it will be in Mode 1.– To enter Mode 2, press the button again.– Pressing the button for the third time the solar light will switch OFF and the blue light will disappear.

Operating Modes:

Mode 1: Sensor Mode– At dusk, it automatically turns to 10% brightness.– Turns on to 100% brightness when motion is detected in the range of <5 meters– In 30 seconds if no motion is detected the light switches to 10% brightness. – Turns off at the dawn.

Mode 2: Constant Brightness Mode– The sensor will be disabled– Automatically turns on at the dusk with 100% brightness and works constantly till the battery capacity goes to Zero. (Upto 4 hours)

STRUCTURE AND SIZE

NOTES

1. This production is a solar energy product. When installing, the solar panels of the product must be illuminated in the direction of the sun. If not placed in the direction of the sun the lamp will not function properly. Resulting in the lamp to no switch ON or the light is functions for a short period of time only. Solar panel should be placed in the direction of the sunlight. The performance of the light is the best if the illumination time of the sunlight is longer than 6 hours resulting in the light to be turned on for its maximum time.
2. This product is mainly installed on the wall and is not allowed to be used in damp or immersed places. Otherwise, it will have a breakdown and affect its service life.
3. The product can achieve the expected brightness and light-up time when the battery is full of electricity. Such as overcast and rainy days, which will cause insufficient charging and shorten the light-uptime. If the lighting time is not long on sunny days, please check whether the solar panels are exposed to the sun for a long time. Or whether the solar panel is dirty and dusty, ensure to keep the solar panels clean.
4. LED Solar light is designed with a replaceable battery. It should be replaced after 3 years of use.After removing the wire connection from the original lithium battery, the battery will be removed and replaced with the new battery of the same specifications.

References

• 
  TAC.EU