V-TAC VT-8084 Microwave Sensor Installation Guide
TECHNICAL DATA
INTRODUCTION & WARRANTY
Thank you for selecting and buying V-TAC product. V-TAC will serve you the best. Please read these instructions carefully before starting the installing and keep this manual handy for future reference. If you have any another query, please contact our dealer or local vendor from whom you have purchased the product. They are trained and ready to serve you at the best.The warranty is valid for 2 years from the date of purchase. The warranty does not apply to damage caused by incorrect installation or abnormal wear and tear. The company gives no warranty against damage to any surface due to incorrect removal and installation of the product. This product is warranted for manufacturing defects only.
The product is a new saving-energy switch, it adopts microwave sensor mould with high-frequency electro-magnetic wave (5.8GHz), integrated circuit. It gathers automatism, convenience, safety, saving-energy and practicality functions. The wide detection field is consisting of detectors. It works by receiving human motion. When one enters the detection field, it can start the load at once and identify automatically day and night. Its installation is very convenient, and it’s using is very wide. Detection is possible through doors, panes of glass or thin walls.
FUNCTION:
- Can identify day and night: It can work in the daytime and at night when it is adjusted on the “sun” position (max). It can work in the ambient light less than 3LUX when it is adjusted on the “3” position (min). As for the adjustment pattern, please refer to the testing pattern.
- SENS adjustable: It can be adjusted according to using location. The detection distance of low sensitivity could be only 5m and high sensitivity could be 15m which fits for large room.
- Time-Delay is added continually: When it receives the second induction signals within the first induction, it will restart to time from the moment.
- Time–Delay is adjustable. It can be set according to the consumer’s desire. The minimum time is 10sec±3sec. The maximum is 12min±1min.
NOTE: the high-frequency output of the HF sensor is <0.2Mw- that is just one 5000th of the transmission power of a mobile phone or the output of a microwave oven, the baby can’t touch it
INSTALLATION DIAGRAM:
- Unload the faceplate of sensor and adjust the time and LUX knob.(refer to figure 1)
- Loose the screws in the connection terminal, and then connect the power to connection terminal of sensor according to connection-wire diagram.
- If you want to install it in circular hole, put the sensor into the hole and tighten the splay bolt on both sides (refer to figure2). If you want to install in quadrate hole, put the sensor into the hole, fix the screw through the mounting hole (refer to figure 3).
- Install back the faceplate, switch on the power and then test it.
TEST:
- Turn the LUX knob clockwise on the maximum (sun). Turn the SENS knob clockwise on the maximum (+).Turn the TIME knob anti-clockwise on the minimum (10s).
- When you switch on the power, the light will be on at once. And 10sec±3sec later the light will be off automatically. Then if the sensor receives induction signal again, it can work normally.
- When the sensor receives the second induction signals within the first induction, it will restart to time from the moment.
- Turn LUX knob anti-clockwise on the minimum (3). If the ambient light is less than 3LUX (darkness), the inductor load could work when it receives induction signal.
NOTE:
When testing in daylight, please turn LUX knob to (SUN) position, otherwise the sensor lamp will not work!
- Do not install the device on uneven or shaky surface
- Install the sensor where there are no objects in front of the sensor obstructing the detection.
- Avoid installing it near metal or glass which may affect the sensor.
- For your safety, please don’t open the case if you find hitch after installation.
- In order to avoid unexpected damage of the product, please add a safe device of current 6A when installing microwave sensor, for example, fuse, safe tube etc.
Warning! Please make sure to turn off the power before starting the installation. Install only by certified Electrician.
This marking indicates that this product should not be disposed of with other household wastes.
Caution, risk of electric shock.
In case of any query/issue with the product, please reach out to us at: For More products range, inquiry please contact our distributor or nearest dealers. V-TAC EUROPE LTD. Bulgaria, Plovdiv 4000, bul.L.Karavelow 9B
References
[xyz-ips snippet=”download-snippet”]