VELLO BG-N21 Battery Grip for Nikon Z User Manual

VELLO BG-N21 Battery Grip for Nikon Z User Manual

Thank you for choosing Vello

The Vello BG-N21 battery grip offers extended shooting time and comfort when shooting in a vertical (portrait) orientation. The grip is compatible with the Nikon Z7 and Z6 mirrorless cameras, and it accepts up to two Nikon EN-EL15a/EN-EL15b rechargeable batteries. You can charge the batteries inside the grip, without removing them, via the included USB-C™M power adapter. The BG-N21 offers an alternate shutter release button that triggers the camera via the included cable, making the grip ideal for shooting portrait photography. And the control-lock switch disables the shutter release button to prevent unwanted exposures.

Please read through this entire manual before using the BG-N21 battery grip.

INTRODUCTION

Precautions
  1. The BG-N21 should be used only with the compatible devices specified in this manual.
  2. Use only with the batteries and battery holders recommended in this manual.
  3. If you notice smoke, noise, or an unusual smell from the battery pack, discontinue use immediately. Remove the batteries, and take the device to a Vello authorized reseller.
  4. The battery level may not display properly if batteries are installed before mounting the grip.
  5. Remove batteries from the grip when not in use.
  6. Do not attempt to disassemble.
  7. Avoid exposing this product to water or extreme humidity, and keep it in a cool, dry place.
  8. Keep out of reach of children.
  9. All images are for illustrative purposes only.
Specifications

OVERVIEW

  1. Battery compartment B
  2. Compartment B battery latch
  3. Camera battery door holder
  4. Shutter release button
  5. Front thumbwheel
  6. Tripod socket
  7. Battery compartment B door
  8. Battery compartment B door latch
  9. Compartment A battery latch
  10. Battery compartment A
  11. 25 mm remote cable socket.
  12. Mounting screw
  13. Rear thumbwheel
  14. Contact cover
  15. Power contacts
  16. Battery power check button
  17. Control lock switch
  18. USB-C port
  19. Battery status LEDs
  20. Battery compartment A door
  21. Battery compartment A door latch
  22. USB-C power adapter
  23. Shutter release cable (2.5 mm)

ASSEMBLY

Attaching the Battery Grip
  1. Ensure that the camera power is turned off, and the grip’s control lock switch is in the Off position.
  2. Remove the camera’s battery chamber door. Pull gently at a 45° angle until the door detaches.
  3. Insert the chamber door into the BG-N21’s camera battery door holder for safekeeping.
  4. Insert the chamber door into the BG-N21’s camera battery door holder for safekeeping.
  5. Insert the chamber door into the BG-N21’s camera battery door holder for safekeeping.
  6. Insert the chamber door into the BG-N21’s camera battery door holder for safekeeping.
Inserting the Batteries
  1. Turn off the camera’s power, and make sure the grip’s control lock switch is in the Off position.
  2. Press the door latch of battery compartment A or B, and slide the door to the rear of the grip, following the arrows. Open the compartment door.
  3. Insert the battery until it locks into place.
  4. Close the compartment door, and slide it to the front of the grip until it clicks.
  5. Turn on the camera power, and make sure the grip’s control lock switch is in the On position.Note: When removing the grip, turn off the camera’s power and the grip’s control lock switch, and then remove the batteries.
Removing the Batteries
  1. Turn off the camera’s power, and make sure the grip’s control lock switch is in the Off position.
  2. Press the door latch of battery compartment A or B. and slide the door to the rear of the grip, following the arrows. Open the compartment door.
  3. Press compartment A’s battery latch to the left until the battery slightly pops out. Press compartment B’s battery latch to the right until the battery slightly pops out.
Checking the Batteries’ Power

Press the CHECK button to check the battery’s power. The LEDs will display the status for 3 seconds.

In-Grip Battery Charging

You can charge the batteries inside the grip, without removing them, using the included 5 V / 2.4 A power adapter. Make sure you turn off the camera to begin charging. Then use the included power adapter to connect the battery grip’s USB-C port to an AC outlet.

report this ad

The LEDs will glow red when charging, and turn off when fully charged. If there are two batteries in the grip, the one with more power will charge first.

References

[xyz-ips snippet=”download-snippet”]

Posted

in

by

admin

Tags:

, , , ,