VIVO Black Electric Single Motor Desk Frame Instruction Manual

VIVO Black Electric Single Motor Desk Frame Instruction Manual

WARNING!

If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual and do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly, or inappropriate use. ELECTRICAL SAFETY INSTRUCTIONSTHIS PRODUCT IS POWERED BY ELECTRICITY. IN ORDER TO AVOID BURNS, FIRE AND ELECTRIC SHOCK, PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY.

  • DO NOT CLEAN PRODUCT WHILE POWER IS CONNECTED. ·
  • DO NOT DISASSEMBLE OR REPLACE COMPONENTS WHILE POWER IS CONNECTED.
  • NEVER OPERATE THE SYSTEM WITH A DAMAGED CORD OR PLUG. PLEASE CONTACT YOURSELLER TO REPLACE DAMAGED PARTS.
  • NEVER OPERATE SYSTEM IN DAMP ENVIRONMENTS OR IF ANY ELECTRICAL COMPONENTS HAVEMADE CONTACT WITH LIQUIDS.
  • ALTERATIONS OF THE GIVEN POWER UNIT ARE NOT ALLOWED
  • OUTDOOR USE IS PROHIBITED.

WARNING: CHOKING HAZARDSMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

PACKAGE CONTENTS

  • A (x12) M6 x 16

  • B (x4) M8 x 50

  • C (x1) 4mm Allen Wrench 5mm Allen Wrench

  • D (x1) 2.5mm Allen Wrench

  • E (x4) M4 x 6

  • F (x15) ST4.2 x 19

  • G (x1) Wrench

  1.  (x2) Foot

  2. (x1) Leg
  3. (x1) Leg with Motor
  4.  (x1) Telescopic Crossbar
  5. (x1) Sync Rod
  6. (x2) Side Bracket
  7. (x1) Adapter
  8. (x2) Baffle
  9. (x1) Power Cable
  10. (x4) Cable Clip
  11. (x1) Adapter Holder

DO NOT EXCEED WEIGHT CAPACITY.Failure to do so may result in serious injury.

TOOLS NEEDED

Warning: Pinch PointDo not place hand on or near support bars. Moving parts can crush and cut. Pinch points are created during lifting and lowering the work surface. Failure to follow these instructions may result in serious personal injury.

Assembly Steps

STEP 1:Place the feet (1) on the legs (2, 3) as shown. Insert and tighten M6 x 16 bolts (A) using the 5mm Allen wrench (C).

STEP 2:Loosen the four set screws on the telescopic crossbar (4) using the 4mm Allen wrench and adjust the crossbar length to suit the desktop. Attach the telescopic crossbar to the legs as shown using M8x50mm bolts (B), and tighten with the 5mm Allen wrench. Retighten all screws.

STEP 3:Loosen the nut on the sync rod (5) and insert the hex rod end into the leg. While holding the hex end, pull the larger rod out until the connector   with the motor connector. Tighten the set screw on the connector using the 2.5mm Allen wrench (D), then tighten the nut using the wrench (G).

STEP 4:Attach the side brackets (6) to both ends of the frame with top portions facing out using four M6x16mm bolts (A). For small desktops down to 31.5″ in width, attach brackets so top portions are instead facing in towards the center. Tighten with the 5mm Allen wrench (C).

STEP 5:Assemble baffles (8) to telescopic crossbar (4) using M4x6mm bolts (E), and tighten with the 2.5mm Allen wrench (D). Baffles may be used to cover the sync rod, or they may be used in the opposite direction to support cables.Hang adapter holder (11) over telescopic crossbar, and place adapter (7) in the holder.

STEP 6:Place the desktop on the frame, holding the controller in the desired location, and drill pilot holes for screws. Use a 3/32″ or 3mm bit, and drill holes to a depth of 3/8″ (10mm). Secure the frame and controller to the desktop   ST4.2×19 screws (F) with a Phillips screwdriver.

STEP 7:Connect the adapter to the cable from the motor and controller. Connect the power cable (9) to the adapter, then connect the power cable to a wall outlet to power on the desk for operation. Organize cables using the cable clips (10).

CONTROLLER

Press and hold the UP or DOWN buttons to operate the desk.

TROUBLESHOOTING

DESCRIPTION

RESOLUTION

No response while pressing button Check to make sure all cables are fully connected.
The desktop cannot be lifted Make sure the desktop and other items do not exceed the weight limit (154lbs).
Duty cycle exceeded (max. 2min operating) Allow desk to rest for 30 minutes.

CAUTION!

Do not exceed desk weight limit.Keep area of vertical motion free of obstacles.Keep weight on desk balanced for correct operation and longer life of components.Leave enough slack in cables to allow for full range of vertical motion.

Failure to follow these instructions may result in property damage and/or personal injury.

Contact: 

Open Monday – Friday 7:00am – 7:00pm CST, our dedicated support team can offer immediate assistance with rapid response times. If any parts are received damaged or defective, please contact us. We are happy to replace parts to ensure you have a fully functioning product.Email: Web: www.vivo-us.comPhone: 309-278-5303FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com

References

[xyz-ips snippet=”download-snippet”]


Posted

in

by