Blue Electric Commercial Cotton Candy MachineInstruction Manual
SKU: CANDY-V002B
Scan the QR code with your mobile device or follow the link for helpful videos and specifications related to this product.https://vivo-us.com/products/candy-v002b
https://vivo-us.com/products/candy-v002b
GET IN TOUCHMonday-Friday from 7:00am-7:00pm CST[email protected] www.vivo-us.comChat live with an agent! 309-278-5303
WARNING: IMPORTANT SAFETY INFORMATION READ AND FOLLOW ALL SAFETY REQUIREMENTS KEEP THIS MANUAL IN A SAFE AND DRY PLACE FOR FUTURE REFERENCEIf you do not understand these directions, or if you have any doubts about the safety of the installation, please call a qualified technician. Check carefully to make sure there are no missing or defective parts.Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual and do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly, or inappropriate use.
- ENSURE THAT SERVICING IS DONE BY PROFESSIONAL SERVICE PERSONNEL, IF APPLICABLE, TO MINIMIZE PRODUCT DAMAGE OR SAFETY ISSUES.• ALL MINORS MUST BE SUPERVISED WHILE THE MACHINE IS IN OPERATION.• THIS APPLIANCE IS NOT INTENDED FOR USE BY PERSONS (INCLUDING CHILDREN) WHOSE PHYSICAL, SENSORY OR MENTAL CAPABILITIES MAY BE DIFFERENT OR REDUCED, OR WHO LACK EXPERIENCE OR KNOWLEDGE UNLESS SUCH PERSONS RECEIVE SUPERVISION OR TRAINING TO OPERATE THE APPLIANCE BY A PERSON RESPONSIBLE FOR THEIR SAFETY.• PLUG THE MACHINE INTO AN ELECTRICAL OUTLET WITH A GROUND LINE.
- DO NOT TOUCH THE SURFACE OF THE HEATING HEAD WHILE THE MACHINE IS ON.
- DO NOT PLACE YOUR HAND INTO THE PAN TO REMOVE THE SUGAR WHILE THE MACHINE IS ON.
- DO NOT MOVE THE MACHINE WHILE IT IS ON.
- ALLOW THE MACHINE TO COOL BEFORE MOVING IT OR REMOVING EXCESS SUGAR.
ELECTRICAL DATA
PRODUCT SPECIFICATIONS
MODEL | CANDY-V002B |
DIMENSION | 930 x 520 x 860mm |
HEATING POWER | 1000 W |
MOTOR POWER | 80 W |
ELECTRIC VOLTAGE | 110 V |
FREQUENCY | 60 Hz |
YIELD | 1 PER 30 SEC |
FUSE | 15A 250V (F15) |
PACKAGE CONTENTS
PREPARATION
- After carefully removing the machine from the packing carton, clean the heating head and the stainless steel pan with warm, soapy water (do NOT use detergent type cleaners). When the head is turned on, it will clear the water from the machine. Make sure to dry the pan completely.
- The cotton candy machine should be placed on a dry, flat stable surface.
- Make sure all parts are properly installed before plugging in the machine.
NOTE: Due to the operation testings of the machine prior to shipping, some sugar residue may be remaining.
MACHINE STRUCTURE
ASSEMBLY STEPS
STEP 1Remove all x6 M5x30 screws (A5) from the Beams (A4). Assemble one beam to each side of the wheel leg (A2) using x2 M5x30 screws (A5). Connect Legs (A3) to assembly using x2 M5x30 screws (A5) through the upper holes. Finish the assembly as shown by mounting the remaining beam (A4) to lower holes in legs (A3) using x2 M5x30 screws (A5).
STEP 2Mount both wheels (A1) using the wheel screws (A6) and washers (A7). Tighten using the small end of included socket wrench (A8).
STEP 3Press both wheel covers (A9) onto wheels.
STEP 4Flip finished cart over and place (B7) machine on top with drawer facing to the side. Secure with all (B4) M5x8 cart screws.
STEP 5Press both (B1) handle blocks onto (B2) handle pipe. Secure to (B6) shelf using four (B9) M5x10 screws and four (B8) M5 nuts. The handle should be facing up.
STEP 6Attach (B5, B6) shelves to machine using all (B3) M4x12 screws.NOTE: Be sure that the shelf with the handle is on the same side as the wheels.
STEP 7Latch pan (B10) to the top of the machine.Your cotton candy machine is now ready for use!
OPERATING INSTRUCTIONS
STEP 1Turn on the power switch. Let the machine run for 1-2 minutes to allow the motor and drive belt to warm up for best performance. The machine may vibrate while running; this is normal and will not affect operation.NOTE: The machine has a built-in safety switch and will not turn on if the bowl is not fully mounted. All four latches should activate the safety switch. Ensure the bowl is in place and secure – red light should be illuminating from the switches.STEP 2 Turn on the heating switch and allow the head to warm up for 4-5 minutes.NOTE: To protect candy from debris and prevent the sugar crystals from flying into the air, we suggest purchasing our bubble shield (CANDY-V003) which is sold separately.STEP 3OPTION A: CANDY FLOSS SUGARIf using standard candy floss sugar, pour one scoop full of sugar into the center of the heating head.OPTION B: HARD CANDYIf using hard candy, turn off the machine and place hard candy pieces evenly in the center of the heating head. Break up into smaller pieces to fit if necessary.Turn the machine back on.NOTE: Only use corn syrup-based hard candies with a slightly transparent appearance such as Jolly Rancher and Life Savers.Pressed sugar and other hard candies like Smarties may not melt properly, thus clogging the head.
CARE & MAINTENANCE
CLEANINGWhen finished making candy floss, keep the machine hot and running while cleaning the heating head by slowly pouring a small amount of water into the center.
TROUBLESHOOTING
WARRANTYWe offer a ONE-YEAR warranty for this product. If you have any problems with the machine, please contact us directly. We have a 30 Day Return Policy.
PROBLEM |
POSSIBLE CAUSE & SOLUTION |
The heating head spins but does not heat up. | Ensure wires underneath the heating head are not cut or frayed. If wires are not damaged then the temperature sensor may be out. |
The machine has no power. | Bowl may not be secured to the machine (all four latches should activate the safety switch). If the safety switch is pressed and switches are on, check if the red light is illuminating from the switches.Contact us for further assistance if it is still not working. |
The electric cord for the machine is lost. | The standard cord used for computers, printers, etc. must be rated 20 AMPS. The cotton candy machine is designed to run on US 110V power. |
The machine constantly vibrates. | The Head/spinner is off balance. Contact us so that we may send you a part replacement. |
Heating head not turning, motor running. | Ensure the belt inside the machine has not come loose. If the belt has come loose, reinstall the machine and adjust the belt tension by loosening the 4 motor screws and repositioning the motor slightly. Replace the belt if broken. |
LAST UPDATED: 02/11/2021REV1
[email protected] | AVG. RESPONSE TIME (within office hrs): 1HR 8M– 23% within < 15m– 38% within < 30m– 61% within < 1hr– 83% within < 2hr– 92% within < 3hr | |
www.vivo-us.comChat live with an agent! | AVG. RESOLUTION TIME (within office hrs): < 15 M | |
309-278-5303 | AVG. RESOLUTION TIME (within office hrs): 5M 4S |
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
References
[xyz-ips snippet=”download-snippet”]