VIVO Dual Monitor Desk Stand Instruction Manual
SKU: STAND-V002F
Scan the QR code with your mobile device or follow the link for helpful videos and specifications related to this product.https://vivo-us.com/products/stand-v002f
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST
[email protected]www.vivo-us.com Chat live with an agent!309-278-5303
WARNING!If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.
TIPOVER WARNINGSERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
- TO PREVENT TIPPING, PLEASE BE CAREFUL NOT TO EXTEND THE ARMS TOO FAR FORWARDOR BACKWARD.
- NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR ORSTAND.
- USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARDSMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
PACKAGE CONTENTS
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
TOOLS NEEDED
DO NOT EXCEED WEIGHT CAPACITY.Failure to do so may result in serious injury.
ASSEMBLY STEPS
STEP 1Install the pole (A) to the base (B) using M5x14 Screw (S-A). Tighten with the 3mm Allen wrench (T-A).
STEP 2Slide Wire Clip (F) and Swivel Arm (C) down onto the Pole (A) and tighten the screw with 6mm Allen Wrench (T-C). Attach the Pole Cap (E) to the top of the Pole (A). Attach the Wire Clips (G) to the Arms.
STEP 3OPTION A: Flat Back MonitorAttach the VESA plates (D) to the monitors using M4x12 Thumbscrew (S-B).
NOTE: Hand tighten screws to avoid stripping the plastic screw heads.
OPTION B: Curved Back Monitor Attach the VESA plates (D) to the monitors using M4 Spacers (S-E) and M4x30 Screws (S-D). Tighten with a Phillips screwdriver.
STEP 4Slide the monitors onto the heads of swivel arm and install the Security Nuts (S-C). Make sure the security nuts are installed before you rotate the monitors.
STEP 5Tighten the bolt on the side of the tilt joint with the 5mm Allen Wrench (T-B) to fix the tilt angle.
To level the monitors, remove the security nut and turn the bolt with the 3mm Allen Wrench (T-A) to raise or lower the monitor. Replace nut after the adjustment.
STEP 6Use the 5mm Allen Wrench (T-B) to adjust swivel joints if needed. Manage cables and store the Allen Wrenches (T-A, T-B, T-C) in Wire Clip (F) for future use.
STEP 7CAUTION: To prevent tipping, please be careful not to extend the arms too far forward or backward.
Love your new VIVO setup and want to share? Tag us in your photo! @vivo_usLAST UPDATED: 02/24/2021 REV1.0
Open Monday – Friday 7:00am – 7:00pm CST, our dedicated support team can offer immediate assistance with rapid response times. If any parts are received damaged or defective, please contact us. We are happy to replace parts to ensure you have a fully functioning product.
[email protected]AVG. RESPONSE TIME (within office hrs): 1 HR 8 M– 23% within < 15m– 38% within < 30m– 61% within < 1hr– 83% within < 2hr– 92% within < 3hr
www.vivo-us.comChat live with an agent!AVG. RESOLUTION TIME (within office hrs): < 15 M
309-278-5303AVG. RESOLUTION TIME (within office hrs): 5 M 4 S
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
References
[xyz-ips snippet=”download-snippet”]