vtech Video Baby Monitor User Guide

Table of Contents

Video Baby Monitor

CONFORMS TO UL STD. 62368-1 CERTIFIED TO CSA STD. C22.2 NO.62368-1

Crystal controlled PLL synthesizerBaby unit: 2405 – 2475 MHz Parent unit: 2405 – 2475 MHz322.8″ Color LCD (QVGA 320×240 pixel)Maximum power allowed by FCC and IC. Actual operating range may vary according to environmental conditions at the time of use.Parent unit: 3.6V, 2600mAh, 9.36Wh Li-ion battery Baby unit power adapter: Output: 6V DC @ 400mA Parent unit power adapter: Output: 5V DC @ 1A

Credits: The Background Noise sound file was created by Caroline Ford, and is used under the Creative Commons license. The Stream Noise sound file was created by Caroline Ford, and is used under the Creative Commons license. The Crickets At Night sound file was created by Mike Koenig, and is used under the Creative Commons license. The Heart Beat sound file was created by Zarabadeu, and is used under the Creative Commons license.Specifications are subject to change without notice. © 2020 VTech Communications, Inc. All rights reserved. 11/20. VM3254-X_QSG_V1.

Go to www.vtechphones.com to register your product for enhanced warranty support and the latest VTech product news.Quick start guide

Frequency control Transmit frequency Channels LCD Nominal effective range Power requirements

VM3254 VM3254-2Video Baby Monitor

For more support informationS m

VM3254

VM3254-2

Important safety instructions

The applied nameplate is located at the bottom of the baby unit’s base. When using your equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury, including the following:1. Follow all warnings and instructions marked on the product.2. Adult setup is required. 3. CAUTION: Do not install the baby unit at a heightabove 2 meters. 4. This product is not a substitute for adult supervision of theinfant. Supervising the infant is the parent’s or caregiver’s responsibility. This product could cease operating, and therefore you should not assume it will continue working properly for any given period of time. Further, this is not a medical device and should not be used as such. This product is intended to assist you in supervising your baby. 5. Do not use this product near water. For example, do not use it next to a bath tub, wash bowl, kitchen sink, laundry tub or swimming pool, or in a wet basement or shower.6. CAUTION: Use only the battery provided. There may be a risk of explosion if a wrong type of battery is used for the parent unit. The battery cannot be subjected to high or low extreme temperature and low air pressure at high altitude during use, storage or transportation. Disposal of battery into fire or a hot oven, or mechanically crushing or cutting or the battery can result in an explosion. Leaving the battery in an extremely high temperature surrounding environment can result in an explosion or the leakage of flammable liquid of gas. Battery subjected to extremely low air pressure may result in an explosion or the leakage of flammable liquid or gas. Dispose of used battery according to the information in The RBRC seal.7. Use only the adapters included with this product. Incorrect adapter polarity or voltage can seriously damage the product.Power adapter information: Parent unit output: 5V DC 1A VTech Telecommunications Ltd. Model: VT05EUS05100 Baby unit output: 6V DC 400mA. VTech Telecommunications Ltd. Model: VT05EUS06040Rechargeable battery information: Zhuhai Great Power Energy Co., Ltd. Li-ion battery, 3.6V, 2600mAh, 9.36Wh; Model: ICR18650-2.6Ah-3.6V-1S1P 8. The power adapters are intended to be correctly oriented in a vertical or floor mount position. The prongs are not designed to hold the plug in place if it is plugged into a ceiling, under-the-table or cabinet outlet. 9. For pluggable equipment, the socket-outlet shall be installed near the equipment and shall be easily accessible. 10. Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning. 11. Do not cut off the power adapters to replace them with other plugs, as this causes a hazardous situation. 12. Do not allow anything to rest on the power cords. Do not install this product where the cords may be walked on or crimped. 13. This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply in your home, consult your dealer or local power company. 14. Do not overload wall outlets or use an extension cord. 15. Do not place this product on an unstable table, shelf, stand or other unstable surfaces. 16. This product should not be placed in any area where proper ventilation is not provided. Slots and openings in the back or bottom of this product are provided for ventilation. To protect them from overheating, these openings must not be blocked by placing the product on a soft surface such as a bed, sofa or rug. This product should never be placed near or over a radiator or heat register.

17. Never push objects of any kind into this product through the slots because they may touch dangerous voltage points or create a short circuit. Never spill liquid of any kind on the product.18. To reduce the risk of electric shock, do not disassemble this product, but take it to an authorized service facility. Opening or removing parts of the product other than specified access doors may expose you to dangerous voltages or other risks. Incorrect reassembling can cause electric shock when the product is subsequently used.19. You should test the sound reception every time you turn on the units or move one of the components.20. Periodically examine all components for damage. 21. There is a very low risk of privacy loss when usingcertain electronic devices, such as baby monitors, cordless telephones, etc. To protect your privacy, make sure the product has never been used before purchase, reset the baby monitor periodically by powering off and then powering on the units, and power off the baby monitor if you will not use it for some time. 22. Children should be supervised to ensure that they do not play with the product. 23. The product is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.SAVE THESE INSTRUCTIONSCautions 1. Use and store the product at a temperature between32oF and 104oF. 2. Do not expose the product to extreme cold, heator direct sunlight. Do not put the product close to a heating source. 3. Batteries should not be exposed to excessive heat such as bright sunshine or fire.

Warning–Strangulation Hazard–

Children have STRANGLED in cords.

Keep this cord out of the reach of

children (more than 3 ft (0.9m) away). Do

not remove this tag.

5. Never place the baby unit(s) inside the baby’s crib or playpen. Never cover the baby unit(s) or parent unit with anything such as a towel or a blanket.

6. Other electronic products may cause interference with your baby monitor. Try installing your baby monitor as far away from these electronic devices as possible: wireless routers, radios, cellular telephones, intercoms, room monitors, televisions, personal computers, kitchen appliances and cordless telephones.

Precautions for users of implanted cardiac pacemakers

Cardiac pacemakers (applies only to digital cordless devices):

Wireless Technology Research, LLC (WTR), an independent research entity, led a multidisciplinary evaluation of the interference between portable wireless devices and implanted cardiac pacemakers. Supported by the U.S. Food and Drug Administration, WTR recommends to physicians that:

Pacemaker patients

· Should keep wireless devices at least six inches from the pacemaker.

· Should NOT place wireless devices directly over the pacemaker, such as in a breast pocket, when it is turned ON.

WTR’s evaluation did not identify any risk to bystanders with pacemakers from other persons using wireless devices.

Electromagnetic fields (EMF)

This VTech product complies with all standards regarding electromagnetic fields (EMF). If handled properly and according to the instructions in this user’s manual, the product is safe to be used based on scientific evidence available today.

Strangulation HazardKeep this cord out of reach of children. The cord needs to be at least three feet away from the child at all times. Do not use with an extension cord. Do not remove this tag.Risque d’étranglement Éloignez ce cordon des enfants. Le cordon doit se trouver à au moins trois pieds d’un enfant et ce, en tout temps. N’utilisez pas de rallonge. Ne retirez pas cette étiquette.Riesgo de estrangulación Mantenga este cable fuera de la alcance de los niños. Este cable debe estar por lo menos tres pies fuera de la alcance del niño en todo momento. No lo use con una extensión inalámbrica. No quite esta etiqueta.

KTeaheurewpseacetyohmifrworisdtvochenometratehdnihdseoestxutctatohegi.olnfbsderieaoatatnclaclehloatroisftd.mtcehhDisrl.oedenrD feooten.netot StranHdga’zéultarRaritaedisnsoqtRgrilunaeeesnmggeoulntdaeción ÉlcopoiirNgc’edenudottseitnlzieds’dcéeueotizintcqpseouraenesfdttartodneone.turdevatleelsrcoeeà,nnagfeeuan.nttmNos.eouirtLneetstietrremozipssp.as Mdlaeodnlcteeolomessnetnninangiuñoaeñnostaioetessrq.etneuxeEsttestceotpaained.seboiclsaóefmfbnuloiueernemraadleaeádnbdtemeelo.lbaeraisNatlcaolacal.rcaoanpNncuoocsreeequite KTeaheurewpseacetyohmifrwrosidtvochenometratehdnihdseoestxutctatohegi.olnfbsderieaoatatnclaclehloatroisftd.mtcehhDisrl.oedenrD feooten.netot StranHdga’zéultarRaritaedisnsoqtRgrilunaeeesnmggeoulntdaeción ÉlcopoiirNgc’edenudottseitnlzieds’dcéeueotizintcqpseouraenesfdttartodenone.turdevatleelsrcoeeà,nnagfeeuan.nttmNos.eouirtLnetestietrremozipssp.as Mdlaeodnlcteeolomessnetnninangiuñoaeñnostaioetessrq.etneuxeEsttescteotpaained.seboiclsaóefmfbnuloiueernemraadleaeádnbdtemeelo.lbaeraisNatlcaolacal.rcaoanpNncuoocsreeequite

What’s in the box1 set for VM3254 2 sets for VM3254-2Quick start guide1 Connect the baby monitorNOTES · The rechargeable battery in the parent unit is built-in. · Use only the power adapters supplied with this product. · Make sure the baby monitor is not connected to a switch-controlled electric outlet. · Connect the power adapters in a vertical or floor mount position only. The adapters’ prongs are notdesigned to hold the weight of a baby monitor, so do not connect them to any ceiling, under-thetable, or cabinet outlets. Otherwise, the adapters may not properly connect to the outlets. · Make sure the parent unit, the baby units and the power adapter cords are out of reach of children.Strangulation HazardKeep this cord out of reach of children. The cord needs to be at least three feet away from the child at all times. Do not use with an extension cord. Do not remove this tag.Risque d’étranglement Éloignez ce cordon des enfants. Le cordon doit se trouver à au moins trois pieds d’un enfant et ce, en tout temps. N’utilisez pas de rallonge. Ne retirez pas cette étiquette.Riesgo de estrangulación Mantenga este cable fuera de la alcance de los niños. Este cable debe estar por lo menos tres pies fuera de la alcance del niño en todo momento. No lo use con una extensión inalámbrica. No quite esta etiqueta.

Technical specifications

Basic operation – Parent unit

Overview – Baby unit

Use the menu

Adjust parent unit speaker volume

Zoom

Press MENU to enter the menu, or save a setting. You can use the parent unit for advanced

· Press VOL+ / VOL- to adjust your

1. Press MENU when in idle mode.

settings or operations, such as to play or stop the baby unit’s lullaby, or to adjust the baby unit’s sound sensitivity.

parent unit speaker volume.

2. Choose .

2 3

3. Press or to choose (Zoom in) or

While in the menu:· Press or to scroll among the menu options.· Press or to select an item. · Press SELECT to confirm yourselection.

Submenu Main menu

(Zoom out), then press SELECT to

confirm your selection.

· Press TALK/EXIT to exit the menu and return to live view.

Talk to your baby unitPress and hold TALK and speak to your parent unit. Your voice is transmitted to the baby unit. Release TALK when done talking and hear your baby again.

Turn off the screenPress POWER/LCD OFF to switch off the screen. You can still hear sound from the selected baby unit.

Press and hold

Tip· Press any key on the parent unit to turn on the screen again.

Overview – Parent unit

7 8

1 Battery LED light

5 LINK LED light

7 POWER/LCD OFF

2 3-level sound indicator light

On when the parent unit is linked to the baby

Microphone

3 · Arrow keys

unit.

9 Power jack

VOL+ / VOL-

Flashes when the link to the baby unit is lost.

RESET

4 MENU/SELECT

6 TALK/EXIT

· Force reboot the parent unit.

Press and hold to talk to the baby unit.

Speaker

· While in a submenu, press to exit.

1 Microphone 2 Camera lens 3 Infrared LEDs 4 Light sensor 5 POWER LED light

6 Night light

9 Speaker

Night light ON/OFF

ON/OFF switch

8 PAIR hole

11 Power jack

The parent unit and baby unit(s) provided

Slots for wall mounting

are already paired.

Need help?

For operations and guides to help you using your video monitor,

and for latest information and supports, go and check the online

help topics and online FAQs.

Use your smartphone or mobile device to access our online help.

· Go to https://help.vtechphones.com/vm3254 or https://help.vtechphones.com/vm3254-2; OR· Scan the QR code on the right. Launch the camera app or QR code scanner app on your smartphone or tablet. Hold the device’s camera up to the QR code and frame it. Tap the notification to trigger the redirection of the online help.– If the QR code is not clearly displayed, adjust your camera’s focus by moving your device closer or further away until it is clear.

You can also call our Customer Support at 1 (800) 595-9511 [in US] or 1 (800) 267-7377 [in Canada] for help.

VM3254 VM3254-2

1 Connect the baby monitor (cont’d)

Charge the parent unit batteryWhen you have connected and turned on the parent unit, the battery will be charged automatically.Notes· Before using the baby monitor for the first time, charge the parent unit battery for 12 hours. When the parent unit battery is fully charged, the battery icon becomes solid .· It takes longer to charge the battery when the parent unit is turned on. To shorten the charging time, turn the parent unit off while charging.· The standby time varies depending on the sensitivity level you set, your actual use and the age of the battery.

The battery icon indicates the battery status (see the following table).

Battery indicators

Battery status

Action

The screen displays . The light flashes.The battery icon becomes solid .

The battery has very little charge and may be used for only a short time. The battery is fully charged.

Charge without interruption (about 30 minutes). To keep the battery charged, connect it to AC power when not in use.

2 Power on or off the baby monitor

Slide the ON/OFF switch to power on or off your baby unit.

Press and hold POWER to power on or off your parent unit.

Press and hold

Power off Power on

3 Positioning the baby monitorCaution· Keep the baby unit out of the reach of your baby. Never place or mount the baby unit inside the baby’s crib or playpen.

3ft (1m)

Caution· The default volume of your parent unit is level 3, and the maximum volume is level 5. If you experience high-pitched screeching noise from your baby monitor while positioning: – Make sure your baby unit and parent unit are more than 3 feet (1 meter) apart, OR – Turn down the volume of your parent unit.

< 3ft (1m)

Note· To avoid interference from other electronic devices, place your baby monitor at least 3 feet (1 meter) away from devices such as wireless routers, microwaves, cell phones and computers.

4 Status checkOnce you power on both your baby unit and parent unit, your parent unit displays image from the baby unit, and the LINK LED light turns on.The baby unit’s POWER LED light turns on.

Parent unit icons

Status icons

Main menu icons

Connection status · or displays when strong signal strength is detected between the babyunit and the parent unit. · or displays when moderate or low signal strength is detected betweenthe baby unit and the parent unit.Patrol mode · Displays when the parent unit is in PATROL mode (For VM3254-2 only).

Main Sub-menu menuZoom · Zoom in and out of the video displayed from the baby unit.

Settings

or Current view status · Displays the baby unit number of the baby unit that is being viewed.Zoom · Displays when the current image on the parent unit has zoomed in.Night vision · Displays when the baby unit being viewed has activated the night visionfeature.Talkback · Displays when talking back to the baby units from parent unit.Lullaby · Displays when a lullaby is playing.

Temperature

Screen off timer · The parent unit display willdim to conserve energy after your chosen amount of time of inactivity.Brightness · Adjust the parent unit’s LCDscreen brightness level.

Night light · Displays when the baby unit’s night light is turned on.

Mute alert · Displays when the parent unit speaker volume is set to zero.· Displays when the parent unit is talking to the baby unit.

Real-time temperature · Displays the real-time temperature detected by the baby unit in Fahrenheit (oF)

or Celsius (oC) (e.g. 57 oF or 14 oC).

· Turn on/off temperature alert tone.· Set the parent unit to beep whenever the room temperature detected by the baby unit falls outside of the set temperature range.

Battery status

animates when the battery is charging.

· displays solid when the battery is fully charged.

· displays when the battery is low and needs charging.

· Set the minimum/maximum temperature.

· Set temperature display in Fahrenheit (oF) or Celsius (oC).

Main Sub-menu menuSound Detection VOX (Voice Activated Alert) Sensitivity · You can choose to hear sounds from the baby unit all the time, or to only hear sounds that exceed a certain level. Adjust the microphone sensitivity of your baby unit, the higher the sensitivity level, the more sensitive the baby unit is in detecting sounds to be transmitted to the parent unit. See Sound sensitivity and sound activation section.Sound-activated screen · When it is on, and the babyunit detects no sound, the parent unit screen stays off to save power. Once a sound is detected, the parent unit screen and speaker turns on automatically, and you can see and hear your baby. The parent unit will then turn off again after 50 seconds of no sound detection. Note · When the parent unit screen is off and it receives alerts, for example, link lost between parent unit and baby unit, or battery is low, the parent unit screen and speaker will turn on for 10 seconds.

Parent unit icons (cont’d)

Main menu icons

Main Sub-menu menuLullaby

Lullaby volume · Adjust the baby unit’s speakervolume when playing the lullaby.

Warning icons and messagesThe battery is empty and Battery low at needs to be recharged. Parent UnitOperation is in progress.

· Select one of the four melodies to play, or stop a lullaby.

Temperature too high

The temperature detected by the baby unit is higher than the desired temperature alert range.

Night Light· Turn on/off the night light. Monitoring Mode (For VM3254-2 only)Patrol mode · Monitor your baby in PATROLmode, where the screen will cycle through display videos streamed from all the linked baby units (For VM3254-2 only).

Temperature too low

The temperature detected by the baby unit is lower than the desired temperature alert range.

No Link to Camera

The parent unit is searching for baby units or the link between the baby unit and the parent unit is lost.

The parent unit is connected to AC power.

· View the video from your selected baby unit’s camera.

Parent Unit Indication Lights

LINK

· On when the parent unit is linked to the baby unit.· Flashes when the link to the baby unit being viewed is lost.

· On when the parent unit is connected to AC power, or the battery is charging.· Flashes when the parent unit battery is low and needs charging.· Off when the parent unit is disconnected from AC power.

Sound sensitivity and sound activation

Adjust the sound sensitivity of the baby unitYou can choose to hear sounds from the baby unit all the time, or to hear sounds that exceed a certain level. You can use the parent unit to adjust the microphone sensitivity of your baby unit. The higher the sensitivity level, the more sensitive the baby unit is in detecting sounds that transmit to the parent unit. The VOX sensitivity level is preset to the highest level.

VOX Sensitivity levelDescription

HighestThe parent unit speaker is constantly on, and you will hear all sounds (including background noises) from your baby’s room.

HighThe parent unit speaker turns on for soft babbling and louder sounds from your baby. It remains quiet when your baby sleeps soundly.

MediumThe parent unit speaker turns on for loud babbling and louder sounds from your baby. It remains quiet when your baby makes soft sounds.

LowThe parent unit speaker turns on for crying and louder sounds from your baby. It remains quiet when your baby makes soft sounds.

LowestThe parent unit speaker turns on for loud crying or screeching sounds from your baby. It remains quiet when your baby makes soft sounds.

Sound activated screenWhen sound activation is on, the parent unit screen stays off to save power when the baby unit detects no sound. Once the baby unit detects sounds that are louder than the chosen sound sensitivity level, the parent unit screen turns on automatically. It will then turn off again after 50 seconds of no sound detection.

Dim modeThe dim mode is to help you save the parent unit power. Your parent unit display will dim automatically after 10 minutes of inactivity, in which there is neither key pressed nor alert received from the baby unit.10 min inactivity

For VM3254-2 only

Status check – Two baby unitsIf you are viewing baby unit , the POWER LED light of baby unit As baby unit is not being viewed, its POWER LED light flashes.

turns on.

Press any buttonsNote· While the screen is dimmed, any keypress or alert message will trigger the screen to return to the preset brightness level. After 10 minutes of inactivity, it will resume to dim mode.

Night vision

The baby unit has infrared LEDs that allow you to see your baby clearly at night or in a dark room. When the baby unit being viewed detects low light levels, the infrared LEDs are switched on automatically. The images from the baby unit are in black and white, and appears on the screen.Notes· It is normal to see a short white glare on your parent unit screen as the baby unit is adapting to the dark environment.· When the infrared LEDs are on, the images are in black and white. This is normal.Tip· Depending on the surroundings and other interfering factors, like lighting, objects, colors and backgrounds, the display resolution may vary. Adjust the baby unit’s angle or place the baby unit at a higher level to prevent glare and blurry display.

Note· If you power on only one baby unit, your parent unit may display and the LINK LED light will flash.Change different views – Patrol1. Press MENU when the parent unit is idle. 2. Press or to choose . 3. Press or to choose , then press SELECT to confirm your selection.10s

Change different views – Single-cam

1. Press MENU when the parent unit is idle. 2. Press or to choose .3. Press or to choose between and you would like to view.

, then press SELECT to confirm the baby unit

Mount the baby unit on dry wall (optional)

Items to purchaseYou will need to purchase the following items separately to mount your baby unit:

2 screws

2 anchors

Note· The types of screws and anchors you need depend on the composition of the wall.

Insert the screws into the holes and tighten the screws until only 1/4 inch of the screws are exposed.

Note· Check for reception strength and camera angle before drilling the holes.Use a pencil to mark two holes in parallel. Make sure they are the same distance apart as the wall mount holes on the baby unit.

Align the wall mount holes on the baby unit with the screws on the wall. Slide the baby unit down until it locks into place.

Drill two holes in the wall ( 7/23 inch drill bit ). If you drill the holes into a stud, go to step 3.-OR-If you drill the holes into an object other than a stud, insert the wall anchors into the holes. Tap gently on the ends with a hammer until the wall anchors are flush with the wall.

Adjust the camera angle.

Frequently asked questionsBelow are the questions most frequently asked about the baby monitor.

Why does the baby monitor not respond normally?Why don’t the power-on light of the baby unit and parent unit go on when I switch on the units?

Try the following (in the order listed) for common cure: 1. Disconnect the power to the baby units and the parent unit. 2. Wait a few seconds before connecting power back to the baby units and the parent unit. 3. Turn on the baby units and the parent unit. 4. Wait for the parent unit to synchronize with the baby units. Allow up to one minutefor this to take place.Perhaps the parent unit is not connected to the power. Insert the appliance plug into the parent unit and put the adapter in a wall socket. Then, press and hold POWER to switch on the parent unit and to establish connection with the baby unit.Perhaps the baby unit is not connected to the power. Insert the appliance plug into the baby unit and put the adapter in a wall socket. Then, slide the ON/OFF switch to ON to switch on the baby unit and to establish connection with the parent unit.

Why doesn’t my parent Make sure the power is not controlled by a wall switch.

unit charge while connected to AC power?

You may have used the battery for a long time. See Warranty for repair/replacement.

Why is my screen in black and white?

The screen is in black and white during night-time or in a dark room when the night vision feature is activated. This is normal.

Why do I get glare or blurry display on my screen when viewing my baby at night?

During night-time or in a dark room, the surroundings and other interfering factors, like lightings, objects, colors and backgrounds may affect the image quality on your parent unit screen. Adjust the baby unit’s angle or place the baby unit at a higher level to prevent glare and blurry display.

Why does the baby monitor produce a high-pitched noise?Why does the parent unit beep?

The parent unit and baby units may be too close to each other. · Move the parent unit away from the baby units until the noise stops; OR · Turn down the volume of your parent unit.The baby units may be out of range. Move the parent unit closer to the baby units (but not less than 3 feet).The parent unit may not have enough charge for the parent unit to perform normally. Charge the battery in the parent unit until the battery icon becomes solid .

The temperature of your baby’s room may be too high or too low.

Why does the parent unit react too quickly to other sounds?

The baby unit also picks up other sounds than those of your baby. Adjust the VOX sensitivity level to a lower level or lower the parent unit speaker volume.

Why don’t I hear a sound/Why can’t I hear my baby cry?Why can’t I establish a connection? Why is the connection lost every now and then? Why are there sound interruptions?

The parent unit speaker volume may be too low. See Adjust parent unit speaker volume to increase the volume.You may have set a low VOX sensitivity level. See Adjust the sound sensitivity of the baby unit to set to a higher level.The baby units may be out of range. Move the parent unit closer to the baby units (but not less than 3 feet).Other electronic products and wireless products may cause interference with your baby monitor. Try installing your baby monitor as far away from these devices as possible.

If you power on only one baby unit, your parent unit may display , and the LINK LED light will flash.

The RBRC sealThe RBRC seal on the Li-ion battery indicates that VTech Communications, Inc. is voluntarily participating in an industry program to collect and recycle these batteries at the end of their useful lives, when taken out of service within the United States and Canada. The program provides a convenient alternative to placing used Li-ion batteries into the trash or municipal waste, which may be illegal in your area. VTech’s participation makes it easy for you to drop off the spent battery at local retailers participating in the program or at authorized VTech product service centers. Please call 1 (800) 8 BATTERY® for information on Li-ion battery recycling and disposal bans/restrictions in your area. VTech’s involvement in this program is part of its commitment to protecting our environment and conserving natural resources. The RBRC Seal and 1 (800) 8 BATTERY® are registered trademarks of Call2recycle, Inc.FCC and IC regulationsFCC Part 15 This equipment has been tested and found to comply with the requirements for a Class B digital device under Part 15 of the Federal Communications Commission (FCC) rules. These requirements are intended to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help. WARNING: Changes or modifications to this equipment not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. To ensure safety of users, the FCC has established criteria for the amount of radio frequency energy that can be safely absorbed by a user or bystander according to the intended usage of the product. This product has been tested and found to comply with the FCC criteria. The baby unit shall be installed and used such that parts of all persons’ body are maintained at a distance of approximately 8 in (20 cm) or more. The transmitter and antenna of the parent unit shall be held at least 1 in (2.5 cm) from your face. This Class B digital apparatus complies with Canadian requirement: CAN ICES-3 (B)/NMB-3(B)Industry Canada This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device. The term `’IC:`’ before the certification/registration number only signifies that the Industry Canada technical specifications were met. This product meets the applicable Innovation, Science and Economic Development Canada technical specifications.RF radiation exposure statement The baby unit complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. The baby unit should be installed and operated with a minimum distance of 8 in (20 cm) between the baby unit and all persons’ body. Use of other accessories may not ensure compliance with FCC RF exposure guidelines. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment complies also with Industry Canada RSS-102 with respect to Canada’s Health Code 6 for Exposure of Humans to RF Fields.California Energy Commission battery charging testing modeThis baby monitor meets the California Energy Commission (CEC) regulations for energy consumption. Your baby monitor is set up to comply with the energy-conserving standards right out of the box. Follow the instructions to install and charge the battery. The CEC battery charging testing mode is activated while charging. Even if the parent unit is paired to baby units, the CEC battery charging testing mode is activated while it is powered off and charging.

For cETL compliance only

Mesures de sécurité importantes La plaque signalétique appliquée est située au bas du socle de l’unité du bébé. Lorsque vous utilisez votre appareil, vous devriez toujours suivre certaines mesures de précaution de base afin de réduire les risques d’incendie, d’électrocution et de blessures corporelles, dont ceux qui suivent : 1. Observez toutes les instructions et mises en garde inscritessur l’appareil. 2. L’installation par un adulte est requise. 3. MISE EN GARDE: N’installez pas l’unité du bébé à unehauteur supérieure à 2 mètres. 4. Ce produit ne remplace pas la surveillance adulte dunourrisson. La supervision du nourrisson est la responsabilité du parent ou de la personne qui s’occupe de l’enfant. Ce produit pourrait cesser de fonctionner et, par conséquent, vous ne devriez pas présumer qu’il continuera de fonctionner correctement pendant une période de temps donnée. De plus, il ne s’agit pas d’un instrument médical et ne devrait pas être utilisé comme tel. Ce produit est destiné à vous aider à superviser votre bébé. 5. N’utilisez pas cet appareil près de l’eau ni de toute autre source d’humidité, par exemple, près d’une baignoire, cuve à lessive, évier de cuisine, dans un sous-sol humide ni près d’une piscine, dans un soussol humide ou une douche. 6. MISE EN GARDE: Utilisez uniquement les piles fournies. Il existe un risque d’explosion si un autre type de batterie est utilisé pour l’unité Parents. N’incinérez pas les piles. Cellesci risqueraient d’exploser. Jetez les piles usées selon les renseignements suivant le sceau du RBRC. 7. N’utilisez que les adaptateurs inclus avec ce produit. L’utilisation d’un adaptateur dont la polarité ou la tension serait inadéquate risque d’endommager sérieusement le produit et mettre votre sécurité en péril.Informations sur les adaptateurs électriques : Adaptateur de l’unité du parent : Sortie : 5V DC 1A VTech Telecommunications Ltd. Modèle : VT05EUS05100 Adaptateur de l’unité du bébé : Sortie : 6V DC 400mA VTech Telecommunications Ltd. Modèle : VT05EUS06040Informations sur les piles rechargeables : Zhuhai Great Power Energy Co., Ltd. Li-ion battery, 3.6V, 2600mAh, 9.36Wh; Model: ICR18650-2.6Ah-3.6V-1S1P 8. Lorsqu’ils sont branchés dans une prise de courant, les adaptateurs secteur ont été conçus pour être orientés correctement, soit à la verticale ou au plancher. Les broches n’ont pas été conçues pour supporter le poids du bloc d’alimentation et le maintenir en place si celuici est branché dans une prise au plafond, sous une table ou dans un meuble. 9. Pour les PRODUITS À BRANCHER À UNE PRISE DE COURANT, la prise de courant doit être installée près du produit, afin d’assurer une accessibilité sécuritaire à la prise de courant. 10. Débranchez ce produit de la prise de courant avant de procéder au nettoyage. N’utilisez pas de nettoyants en aérosols. Utilisez un chiffon humide pour le nettoyer. 11. Ne coupez pas les cordons d’alimentation pour remplacer les fiches, car ceci peut présenter un danger potentiel. 12. Ne laissez aucun objet reposer ni appuyer sur le cordon d’alimentation. N’installez pas cet appareil dans un endroit où l’on risque d’écraser le cordon d’alimentation ou de le piétiner. 13. Ne faites fonctionner cet appareil qu’avec le type d’alimentation indiqué sur l’étiquette. Si vous ne connaissez pas le type d’alimentation que vous possédez à votre domicile, consultez votre marchand ou votre compagnie locale d’électricité. 14. Ne surchargez pas les prises de courant murales ni les rallonges électriques. 15. Ne placez pas cet appareil sur un chariot, meuble, trépied, support de montage ni table chancelants. 16. Les trous et ouvertures du boîtier, situés à l’arrière de l’appareil ou sous celui-ci, servent à aérer l’appareil. Pour l’empêcher de surchauffer, ne bloquez sous aucun prétexte ces ouvertures et n’empêchez pas l’aération adéquate de l’appareil en le plaçant sur un lit, divan, tapis ou toute autre surface similaire. De même, ne le positionnez pas à proximité ni au-dessus d’une source de chaleur ou d’un calorifère. De plus, ne placez pas l’appareil dans un endroit avant de vous assurer qu’il y ait une bonne circulation d’air.

17. N’enfoncez jamais d’objets à travers les ouvertures de cet appareil, car ils pourraient entrer en contact avec des points de tension dangereux ou causer des courtscircuits qui peuvent dégénérer en incendies ou en risques d’électrocution. Ne renversez jamais de liquide dans ce produit.18. Afin de réduire les risques d’électrocution, ne démontez pas cet appareil, mais apportez-le dans un centre de service autorisé. L’ouverture du boîtier ou le retrait de toutes pièces que contient cet appareil, à l’exception de l’accès autorisé à certaines portes ou ouvertures, risque de vous exposer à des points de tension dangereux ou d’autres dangers. Un remontage incorrect peut par la suite présenter des risques d’électrocution.19. Vous devriez tester la réception chaque fois que vous mettez l’appareil en fonction.20. Examinez les composantes afin de vérifier si celles-ci ne sont pas endommagées.21. Il existe un très faible risque de perte de confidentialité avec certains appareils électroniques (autres écoute-bébés, téléphones sans fils etc.). Pour l’éviter, s’assurer que le produit n’a jamais été utilisé avant l’achat, réinitialiser l’unité de façon périodique, éteindre l’écoute-bébé quand il n’est pas en cours d’utilisation.22. Les enfants devraient être supervisés afin de vous assurer qu’ils ne jouent pas avec l’appareil.23. Le produit n’est pas conçu pour être utilisé par des personnes (incluant des enfants) aux capacités physiques, sensorielles ou mentales réduites ou qui manquent d’expérience et de connaissances, à moins qu’on leur ait donné suffisamment de supervision ou d’instructions relativement à l’utilisation de l’appareil par une personne responsable de leur sécurité. CONSERVEZ CES INSTRUCTIONSMises en garde 1. Utilisez et entreposez le produit à une température entre0° C (32°F) et 40°C (104° F). 2. N’exposez pas cet appareil à des froids ou des chaleursextrêmes, ainsi qu’à la lumière directe du soleil. Ne l’installez pas près d’une source de chauffage. 3. Le bloc-piles ne doit pas être exposé à la chaleur excessive telle que la lumière du soleil ou au feu.

Avertissement – Risque de strangulation

– Les enfants se sont ÉTRANGLÉS dans des

cordons. Gardez ce cordon hors de portée

des enfants (à plus de 0,9 m). N’enlevez pas

cette étiquette.

5. Ne jamais placer le moniteur à l’intérieur du berceau ou du parc de bébé. Ne jamais couvrir le moniteur ou l’unité (s) portative avec un article tel une serviette ou une couverture.

6. D’autres équipements électroniques peuvent produire des interférences sur votre moniteur vidéo et audio. Tentez d’installer votre moniteur vidéo ou audio à l’écart des appareils électroniques tels que des routeurs sans fil, radios, téléphones cellulaires, interphones, moniteurs, téléphones, ordinateurs personnels, électroménagers et téléphones sans fil.

Stimulateurs cardiaques implantés dans l’organisme

Les simulateurs cardiaques (ne s’applique qu’aux dispositifs numériques sans fil) :

L’organisme `Wireless Technology Research, LLC (WTR)’, une firme de recherche indépendante, a mené une évaluation pluridisciplinaire des interférences entre les téléphones sans fil portatifs et les stimulateurs cardiaques implantés dans l’organisme. Appuyée par l’Administration des aliments et drogues (FDA) des États-Unis, la firme WTR recommande aux médecins:

Avis aux détenteurs de stimulateurs cardiaques

· Vous devriez maintenir les dispositifs sans fil à au moins six pouces du simulateur cardiaque.

· Ils ne doivent PAS placer le téléphone sans fil directement sur le stimulateur cardiaque, tel que dans une poche de chemise, lorsque celui-ci est en marche.

L’étude effectuée par l’organisme WRS n’a pas identifié de risque pour les détenteurs de simulateurs cardiaques causés par les gens qui utilisent dispositifs sans fil à proximité de ceux-ci.

Champs électromagnétiques (EMF) Ce produit de VTech est conforme à toutes les normes se rapportant aux champs électromagnétiques (EMF) standard. Si vous le manipulez correctement en suivant les instructions de ce guide, son utilisation sera sécuritaire pendant de nombreuses années, selon les meilleures évidences scientifiques dont nous disposons aujourd’hui.

Limited warrantyWhat does this limited warranty cover? The manufacturer of this VTech Product warrants to the holder of a valid proof of purchase (“Consumer” or “you”) that the Product and all accessories provided in the sales package (“Product”) are free from defects in material and workmanship, pursuant to the following terms and conditions, when installed and used normally and in accordance with the Product operating instructions. This limited warranty extends only to the Consumer for Products purchased and used in the United States of America and Canada.What will VTech do if the Product is not free from defects in materials and workmanship during the limited warranty period (“Materially Defective Product”)? During the limited warranty period, VTech’s authorized service representative will repair or replace at VTech’s option, without charge, a Materially Defective Product. If we repair the Product, we may use new or refurbished replacement parts. If we choose to replace the Product, we may replace it with a new or refurbished Product of the same or similar design. We will retain defective parts, modules, or equipment. Repair or replacement of the Product, at VTech’s option, is your exclusive remedy. VTech will return the repaired or replacement Products to you in working condition. You should expect the repair or replacement to take approximately 30 days.How long is the limited warranty period? The limited warranty period for the Product extends for ONE (1) YEAR from the date of purchase. If VTech repairs or replaces a Materially Defective Product under the terms of this limited warranty, this limited warranty also applies to the repaired or replacement Product for a period of either (a) 90 days from the date the repaired or replacement Product is shipped to you or (b) the time remaining on the original one-year warranty; whichever is longer.What is not covered by this limited warranty? This limited warranty does not cover: 1. Product that has been subjected to misuse, accident,shipping or other physical damage, improper installation, abnormal operation or handling, neglect, inundation, fire, water or other liquid intrusion; or 2. Product that has been damaged due to repair, alteration or modification by anyone other than an authorized service representative of VTech; or 3. Product to the extent that the problem experienced is caused by signal conditions, network reliability, or cable or antenna systems; or 4. Product to the extent that the problem is caused by use with non-VTech accessories; or 5. Product whose warranty/quality stickers, product serial number plates or electronic serial numbers have been removed, altered or rendered illegible; or 6. Product purchased, used, serviced, or shipped for repair from outside the United States of America or Canada, or used for commercial or institutional purposes (including but not limited to Products used for rental purposes); or 7. Product returned without a valid proof of purchase (see item 2 below); or 8. Charges for installation or set up, adjustment of customer controls, and installation or repair of systems outside the unit.

How do you get warranty service? To obtain warranty service in the USA, please visit our website at www.vtechphones.com or call 1 (800) 595-9511. In Canada, go to www.vtechcanada.com or call 1 (800) 267-7377. NOTE: Before calling for service, please review the user’s manual – a check of the Product’s controls and features may save you a service call. Except as provided by applicable law, you assume the risk of loss or damage during transit and transportation and are responsible for delivery or handling charges incurred in the transport of the Product(s) to the service location. VTech will return repaired or replaced Product under this limited warranty. Transportation, delivery or handling charges are prepaid. VTech assumes no risk for damage or loss of the Product in transit. If the Product failure is not covered by this limited warranty, or proof of purchase does not meet the terms of this limited warranty, VTech will notify you and will request that you authorize the cost of repair prior to any further repair activity. You must pay for the cost of repair and return shipping costs for the repair of Products that are not covered by this limited warranty.What must you return with the Product to get warranty service? 1. Return the entire original package and contents includingthe Product to the VTech service location along with a description of the malfunction or difficulty; and 2. Include a “valid proof of purchase” (sales receipt) identifying the Product purchased (Product model) and the date of purchase or receipt; and 3. Provide your name, complete and correct mailing address, and telephone number.Other limitations This warranty is the complete and exclusive agreement between you and VTech. It supersedes all other written or oral communications related to this Product. VTech provides no other warranties for this Product. The warranty exclusively describes all of VTech’s responsibilities regarding the Product. There are no other express warranties. No one is authorized to make modifications to this limited warranty and you should not rely on any such modification. State/Provincial Law Rights: This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state or province to province. Limitations: Implied warranties, including those of fitness for a particular purpose and merchantability (an unwritten warranty that the Product is fit for ordinary use) are limited to one year from the date of purchase. Some states/ provinces do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. In no event shall VTech be liable for any indirect, special, incidental, consequential, or similar damages (including, but not limited to lost profits or revenue, inability to use the Product or other associated equipment, the cost of substitute equipment, and claims by third parties) resulting from the use of this Product. Some states/provinces do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.Please retain your original sales receipt as proof of purchase.

report this ad

Disclaimer and Limitation of LiabilityVTech Communications, Inc. and its suppliers assume no responsibility for any damage or loss resulting from the use of this user’s manual. VTech Communications, Inc. and its suppliers assume no responsibility for any loss or claims by third parties that may arise through the use of this product. Company: VTech Communications, Inc. Address: 9020 SW Washington Square Road – Ste 555 Tigard, OR 97223, United States Phone: 1 (800) 595-9511 in the U.S. or 1 (800) 267-7377 in Canada

References

[xyz-ips snippet=”download-snippet”]

Posted

2023-01-24

vtech

admin

Tags:

_pdf, Baby Monitor, VM3254, VM3254-2, vtech