Westinghouse WSFS1808BK 18 inch Orbit Oscillating Stand Fan Instruction Manual

Westinghouse WSFS1808BK 18 inch Orbit Oscillating 
Stand Fan Instruction Manual

SAFETY INFORMATION

IMPORTANT SAFEGUARDS

WARNING: To reduce the risk of an electric shock and injury to personsor injury, do not use the fan in a window.WARNING: To reduce the risk of a fire or electrical hazards, do not use this fan with any solid state speed control device.

  1. Use this fan only as described in this manual. Using the fan for other purposes may cause a fire, hazards or an electric shock.
  2. This product is intended for household use. It is designed for indoor, non-commercial, non-industrial and general domestic use in cooling rooms and is not intended for use in windows. Do not use the product outdoors or for any other purpose.
  3. To prevent the risk of electrical shock, always use the fan on a dry, level surface. Do not place the fan in a window, immerse the unit, plug or cord in water, or spray with liquids.
  4. Close supervision must be provided when the appliance is used by or near children.
  5. Unplug the unit from the mains outlet when left unattended or not in use, when moving the fan from one location to another, and before cleaning.
  6. Never submerge the unit in water.
  7. Do not operate the unit in the presence of explosive and/or flammable fumes.
  8. Do not place the unit or any parts near open flames or next to cooking or other heating appliances.
  9. Never insert fingers or any other objects through the fan guards. Never drop or insert objects into any opening of the product.
  10. Never plug the unit in with wet hands or a wet cord.
  11. Do not operate the unit with a damaged cord or plug. If the cord or plug is damaged, discard the fan or return it to an authorized service facility for examination and/or repair.
  12. Avoid contact with moving fan parts.
  13. To disconnect the fan from the power supply, grip the plug and pull it from the outlet. Do not pull on the cord.
  14. Do not operate if the fan housing has been removed or damaged.
  15. To prolong the lifespan of the product, do not use the fan continuously for 24 hours a day.
  16. Do not the run cord under carpets. Do not cover the cord with throw rugs, runners, or other similar objects. Do not route the cord under furniture or appliances. Place the cord away from people where it will not present a trip hazard.
POLARIZED PLUG

This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug, if it still does not fit, contact a qualified electrician. Do not modify the plug in any way.

DO NOT ATTEMPT TO MODIFY THIS PLUG OR DEFEAT THIS SAFETY FEATURE IN ANY WAY.

HOW TO USE

PARTS DESCRIPTIONS

  1. Front grille
  2. Blade
  3. Screw
  4. Locking nut
  5. Rear grill
  6. Rotary switch
  7. Oscillation knob
  8. Motor
  9. Screw
  10. Inner Tube
  11. Height adjustment knob
  12. Cover ring
  13. Outer tube
  14. Screw
  15. Base

 

  1. Attach the outer tube (13) to the base (15) with the 4 screws (14) as shown.
  2. Loosen the knob (11) on the outer tube and extend the inner tube (10) to the desired height.
  3. Slide the cover ring (12) down the outer tube to rest on top of the base.Caution: The knob must be fully tightened before assembling the fan head to the inner tube.
  4. Tighten the small screw (9) which is pre-screwed into the small hole of the inner tube.
  5. Position the rear grille (5) over the motor (8) shaft, ensuring that the notches are correctly aligned, and then secure with the locking nut (4).
  6. Align the fan blade (2) with the flat part of the motor (8) shaft, and secure by tightening the fan blade screw (3) fully. The screw should be positioned on the flat part of the motor shaft.
  7. Position the front grille (1) against the rear grille (5) and push the guard ring in place so that it holds both grilles together.
OPERATING INSTRUCTIONS
  1. Place the fan on a dry, level surface.
  2. Make sure the rotary switch is at the “0” (OFF) position. Plug the unit into a 120V AC, 60 Hz outlet.
  3. Adjust the fan head vertically to the desired angle.
  4. To turn on the unit, turn the rotary switch to the “1” (LOW), “2” (MEDIUM) or “3” (HIGH) position.
  5. To stop the unit, turn the rotary switch to the “0” (OFF) position, and then unplug the unit from power outlet.
  6. Unplug the product from the electrical outlet when it is not in use or is left unattended.

CLEANING INSTRUCTIONS

WARNING: To avoid the risk of electrical shock, always make sure the product is unplugged from the electrical outlet before disassembling, cleaning, servicing or relocating.

  1. The product should be cleaned and checked on a regular basis. Make sure the fan blade is clean at all times to prevent the fanblade from damage and fading.The fan can be cleaned in two ways:a) Vacuum the fan blades or use a can of compressed air, orb) Remove the front guard by removing the 3 screws securing the grille to the fan (be sure to use a screwdriver with a magnetic tip).
  2. To clean the front guard, turn counterclockwise to loosen the screw and pull off the guard. To place back on, match the shape of the shaft to the inside groove of the guard and push inwards. Screw the fastener on clockwise to tighten.
  3. Take the guard off and wipe it with a cloth or use a can of compressed air. Make sure the front guard is completely dry before securing it back onto the fan.
  4. Wipe the fan blades (do not remove) with a damp cloth dipped in a light solution of water and mild detergent.
  5. Make sure that water does not get into the motor while cleaning.
  6. The blade and rear guard (not removable) must be completely dry when re-securing the guard in place.
  7. Do not use any chemical cleaners such as acid or alcohol to clean the fan.

CARE AND MAINTENANCE

WARNING: Do not attempt to open any part of the motor housing, as this may cause an electrical shock. This product has been permanently lubricated at the factory and will not require further lubrication for the entire product lifespan. Additional lubrication of electric motor parts could create a fire hazard.

  1. The product must be placed in its original packaging and stored in a room with low humidity.
  2. Make sure the product is completely dry before use

NOTE: If you experience a problem, please return the fan to the retailer. Do not attempt to open the motor housing yourself, as doing so may cause damage to the fan or personal injury.

DISPOSAL

Proper disposal of this product.

This symbol indicates that this appliance may not be treated as household waste. Instead, it should be taken to the appropriate collection point for recycling electrical and electronic equipment.

Please use the return or collections services available in your community or contact the retailer where you purchased this product.

INFORMATION AND SERVICE

If you have questions or concerns about your product, please visit our website: www.westinghousehomeware.com, or contact our overseas offices/agents.

In line with our policy of continuous product development, we reserve the right to change the product, packaging and documentation specifications without prior notice.

Model: WSFS1808BK120VAC 60Hz 61W

 

 

 

 

report this ad

WESTINGHOUSE, and INNOVATION YOU CAN BE SURE OF are trademarks of Westinghouse Electric Corporation, a USA company. Used under license by Westinghouse Homeware (HK) Co. All Rights Reserved.

 

WSFS1808BK • 11/19

References

[xyz-ips snippet=”download-snippet”]

Posted

in

by

admin

Tags:

, , , , , ,