WOLF Induction Electric Cooktop Installation Guide

WOLF Induction Electric Cooktop Installation Guide

Induction/Electric Cooktop

Important Note

To ensure this product is installed and operated as safely and efficiently as possible, take note of the following types of highlighted information throughout this guide:\

IMPORTANT NOTE

highlights information that is especially important.

CAUTION

indicates a situation where minor injury or product damage may occur if instructions are not followed.

WARNING

states a hazard that may cause serious injury or death if precautions are not followed.

IMPORTANT NOTE:

Throughout this guide, dimensions in parentheses are millimeters unless otherwise specified.

IMPORTANT NOTE:

Save these instructions for the local electrical inspector.

Product Information

Important product information, including the model and serial number, are listed on the product rating plate. The rating plate is located on the bottom of the cooktop. Referto the illustrations below. If service is necessary, contact Wolf Factory CertifiedService with the model and serial number. For the name of the nearest Wolf Factory Certified Service or for questions regarding the installation, visit the Product Support section of our website, wolfappliance.com, or call Wolf Customer Care at 800-222-7820.

Specifications

Installation Requirements

A minimum 2″ (51) is required from the bottom of the cooktop to combustible materials. Clearance is required for the conduit located at the right rear of induction and electric cooktops. Refer to the illustration below for dimensions. Refer to the illustrations on pages 6–8 for additional minimum clearances. Installation dimensions are the same forinduction and electric cooktops of the same width.

WARNING

Failure to locate the cooktop without proper clearances will result in a fire hazard.

FLUSH INSTALLATION

Contemporary induction and electric cooktops can be mounted flush with the top of the countertop or as a frameless standard installation sitting on top of the countertopsurface. If the cooktop is to be mounted flush with the countertop, a recessed area surrounding the cooktop cutout must be provided. An installation kit and instructions required for a flush installation are provided with the Contemporary cooktop.

CAUTION

A flush installation is intended for granite, solid surface, or stone countertop surfaces only.

MULTIPLE COOKTOPS

When multiple cooktops or modules are installed side by side, the countertop cutout width is determined by adding the width of each unit, then subtracting 1″ (25). Refer to theillustration below.

IMPORTANT NOTE:

Contemporary induction and electric cooktops are not designed to be installed in combination with other cooktops.

Electrical Requirements

Installation must comply with all applicable electrical codes. Locate the electrical supply as shown in the illustrations on the following pages. A separate circuit servicing onlythis appliance is required. A ground fault circuit interrupter (GFCI) is not recommended and may cause interruption of operation. When multiple cooktops are installed side by side, each unit must have its own separate recommended electrical circuit.

ELECTRICAL REQUIREMENTS

INDUCTION

Electrical Supply                                   3-wire, 240/208 VAC, 60 HzConduit                                                 flexible 4′ (1.2 m)

ELECTRICElectrical Supply                                  3-wire, 240 VAC, 60 HzConduit flexible                                   4′ (1.2 m)

SERVICE

15″ Induction/Electric           20 amp dedicated circuit24″ Induction                         30 amp dedicated circuit30″ Induction/Electric           40 amp dedicated circuit36″ Induction/Electric           50 amp dedicated circuit

15″ CooktopSTANDARD INSTALLATION

NOTE: Shaded area above countertop indicates minimum clearance to combustible surfaces,combustible materials cannot be located within this area.

24″, 30″, and 36″ CooktopsSTANDARD INSTALLATION

                  COUNTERTOP CUTOUT

SIDE VIEW                                          FRONT VIEW

NOTE: Shaded area above countertop indicates minimum clearance to combustible surfaces, combustible materials cannot be located within this area.Electrical supply location only applies to installations with built-in oven.

24″, 30″, and 36″ CooktopsFLUSH INSTALLATION

COUNTERTOP CUTOUT

SIDE VIEW                                                         FRONT VIEW

NOTE: Shaded area above countertop indicates minimum clearance to combustible surfaces, combustible materials cannot be located within this area.Electrical supply location only applies to installations with built-in oven. Outside corner radius 7/16″ (11).

CUTOUT WIDTH                               W                             A24″ Induction                               22 1/8″ (562)             23 3/4″ (603)30″ Induction/Electric                 29″ (737)                   30 1/8″ (765)36″ Induction/Electric 35″          (889)                           36 1/8″  (918)

Flush Installation

To ensure a proper installation, a template for the countertop cutout should be created using the cooktop glass.

ROUTING OPTION

For this installation, a recessed area surrounding the countertop cutout is required. Fabrication of the recessed area bmust take place before the countertop is installed.This option is not recommended for countertops with a molded backsplash.

CLEAT OPTION

For this installation, the countertop cutout is the same size as the outer edge of the cooktop glass. Attach L-shaped cleats to the perimeter of the countertopcutout. The top edge of the cleat cannot be wider than 7/8″ (22) and is attached 5/16″ (8) below the surface of the countertop. Refer to the illustration below. Attach thecleats to the countertop. Consult a countertop supplier for proper methods of attachment.

    Support cleats

Cooktop Installation

Remove the cooktop and components from the shipping package and recycle packing materials.

  1. Lower the cooktop into the countertop cutout. Center the cooktop in the opening with the front edge aligned parallel to the front edge of the countertop. Using apencil, outline the rear edge of the cooktop on the countertop. Remove the cooktop.
  2. Apply the foam strip to the perimeter of the countertop opening. Refer to the illustration below. Do not seal the cooktop to the countertop.
  3. Insert the cooktop into the opening. Verify the cooktop is aligned with the front edge of the countertop.
  4. Attach the provided brackets to the bottom of the unit. Insert the 3 1/2″ (89) clamping screws into the brackets. Use a screwdriver to tighten the clamping screwsagainst the bottom of the countertop. Do not overtighten screws. Refer to the illustration below.

Troubleshooting

IMPORTANT NOTE: If the cooktop does not operate properly, follow these troubleshooting steps:

  • Verify electrical power is supplied to the cooktop.
  • If the cooktop does not operate properly, contact Wolf Factory Certified Service. Do not attempt to repair the cooktop. Wolf is not responsible for service required tocorrect a faulty installation.

Sub-Zero, Sub-Zero & Design, Sub-Zero & Snowflake Design, Dual Refrigeration, The Living Kitchen, Great American Kitchens The Fine Art of Kitchen Design, Wolf, Wolf & Design, Wolf Gourmet, W & Design, red colored knobs, Cove, and Cove & Design are registered trademarks and service marks of Sub-Zero Group, Inc. and its subsidiaries.All other trademarks are property of their respective owners in the United States and other countries.

 

Read More About This Manual & Download PDF:

References

[xyz-ips snippet=”download-snippet”]


Posted

in

by