WyreStorm SW-130-TX-US 3-Input In-wall HDBaseT Transmitter User Guide

Quickstart Guide

3-Input In-wall HDBaseT™Transmitter with USB Host & CEC Trigger. 2-gang US/UK Back-box

SW-130-TX-US | SW-130-TX-UK

WyreStorm recommends reading through this document in its entirety to become familiar with the product’s features prior to starting the installation process.

           

  IMPORTANT! Installation Requirements
  • Visit the product page to download the latest firmware, document version, additional documentation, and configuration tools.
  • Read through the Wiring and Connections section for important wiring guidelines before creating or choosing premade cables.
  • While this product supports CEC, WyreStorm cannot guarantee compatibility with all forms of CEC communication.
In the Box

1x 4-pin Phoenix Male Connector1x USB host cable (Type A-B)1x Decora face plate (SW-130-TX-US)4x Retaining screws (SW-130-TX-US)1x Quickstart guide (This Document)

Basic Wiring Diagram

KEY

HDMI/DisplayPort/USB-C HDBaseT RS-232 Analog Audio USB 2.0

KEY

HDMI/DisplayPort/USB-C HDBaseT RS-232 Analog Audio USB 2.0

SW-130-TX-US (Front/Rear)

       

SW-130-TX-UK (Front/Rear)

       

(A) HDMI Inputs 19-pin type A HDMI female

Supports HDMI and DVI/D with adapter

(B) USB-C Input USB3.1C port

Supports alt-mode and device charging

(C) Source LED On: Indicates the selected source
(D) HDCP LED On: Indicates encrypted source content

Off: Indicates non-encrypted source content

(E) Link LED On: Indicates link established with receiving device

Off: No link with receiver or receiver powered off

(F) Power LED Solid: The unit is powered On

Off: The unit is powered Off

(G) Display Trigger Short Press: Send power on trigger

Long Press: Send power off trigger

(H) Input Select Press to manually change input
(I) Audio Line In 3.5mm jack: 2ch analog audio input
(J) USB Host USB Type A female

Connection of USB Host device

 

(A) HDBT Out 8-pin RJ-45 female

Connect the transmitter’s HDBT OUT to receiver’s HDBT IN.

(B) RS-232 4-pin phoenix: Serial input for API control and 12v DC input
Wiring and Connections

WyreStorm recommends that all wiring for the installation is run and terminated prior to making connections to the switcher. Read through this section in it’s entirety before running or terminating the wires to ensure proper operation and to avoid damaging equipment.

  IMPORTANT! Wiring Guidelines
  • The use of patch panels, wall plates, cable extenders, kinks in cables, and electrical or environmental interference will have an adverse effect on signal transmission which may limit performance. Steps should be taken to minimize or remove these factors completely during installation for best results.
  • WyreStorm recommends using pre-terminated HDMI and USB cables due to the complexity of these connector types. Using pre-terminated cables will ensure that these connections are accurate and will not interfere with the performance of the product.
  • This product contains a USB-C connection that can be used as an audio/video input. When using this connection verify that the USB-C cable used supports audio/video functionality as not all USB-C cables support this requirement.
Cat6 Cable Performance Guide
0m 10m 20m 30m 40m 50m 60m 70m 80m 90m 100m
 
0ft 32ft 65ft 98ft 131ft 164ft 197ft 230ft 262ft 295ft 328ft
  4K/HD Transmission
WyreStorm recommends the use of shielded cable to minimize signal noise and interface
Audio Connections

Audio InThe audio connections use a 3.5mm (1/8in) TRS Stereo Jack.

  1. Tip: Left Channel
  2. Ring: Right Channel
  3. Sleeve: Ground (GND)
RS-232 Wiring

The SW-130-TX-Ux uses a 4-pin RS-232 with no hardware flow control. Most control systems and computers are DTE where pin 2 is RX, this can vary from device to device. Refer to the documentation for the connected device for pin functionally to ensure that the correct connections can be made.Refer to RS-232 Mode Settings for details on setting RS-232 modes.

WyreStorm Connector   3rd Party Device
Pin 1 12V DC Out No Connection Reserved
Pin 2 TX (Transmit) —> To —> RX (Receive)
Pin 3 RX (Receive) —> To —> TX (Transmit)
Pin 4 G (Ground) —> To —> G (Ground)
Troubleshooting

No or Poor Quality Picture (snow or noisy image)

  • Verify that power is being supplied to the transmitter and receiving device.
  • Verify that all HDMI, USB and HDBaseT connections are not loose and are functioning properly.
  • Verify that the HDBaseT cable is properly terminated following EIA568B standard.
  • Verify that the output resolution of the source and display is supported by this extender.
  • If transmitting 3D or 4K, verify that the HDMI cables used are 3D or 4K rated.

No or Intermittent 3rd party Device Control

  • Verify that the RS-232 cables are properly terminated following the Wiring and Connections section.
Troubleshooting Tips:
  • WyreStorm recommends using a cable tester or connecting the cable to other devices to verify functionality.

Note: WyreStorm reserves the right to change product specification, appearance or dimensions of this product at any time without prior notice.

Warranty InformationWyreStorm Technologies LLC warrants that its products to be free from defects in material and workmanship under normal use for a period of five (5) years from the date of purchase. Refer to the Product Warranty page on wyrestorm.com for more details on our limited product warranty.

Specifications
Transmission
Transmission Encoding HDBaseT Class C | PAM16 Encoding
End to End Latency 10µs
Maximum Transmission Bit Rate 10.2Gbps
Video
HDMI v2.0b TMDS | 340MHz Maximum
Inputs 2x HDMI In: 19-pin type A | 1x USB-C In: USB 3.1c Audio/Video (4.5Gbps)
Outputs 1x HDBT out: 8-pin RJ45
Maximum Pixel Clock HDMI & HDBaseT: 340MHz
Video Resolutions (Max) Video Resolution HDMI Cat6 Cat6a/7
1920x1200p @60Hz 70m/230ft 70m/230ft 100m/328ft
2560x1440p @60Hz 15m/49ft 100m/328ft 100m/328ft
3840x2160p @30Hz 8bit 4:4:4 7m/23ft 70m/230ft 100m/328ft
3840x2160p @30Hz 10bit 4:2:0 HDR 5m/16ft 70m/230ft 100m/328ft
3840x2160p @30Hz 12bit 4:2:2 HDR 5m/16ft 70m/230ft 100m/328ft
Note: WyreStorm recommends the use of shielded category cable to minimize signal noise and interference.
Supported Standards DCI | RGB | HDR | HDR10 | Dolby Vision up to 30Hz | HLG | BT.2020 | BT.2100
Audio
Inputs 1 x Audio In: 3.5mm (1/8in) TRS Stereo

2ch audio over HDBaseT | 1-way to RX

Audio Formats 2ch PCM | Multichannel up to DTS-X and Dolby Atmos
Maximum Sampling Rate 192KHz
Maximum Audio Channels 32
Audio Return Channel (ARC) Not Supported
Communication and Control
USB Host (HDMI Inputs) 1x Type B host | Maximum data throughput: 190Mbps
USB 3.1c Alt-mode Supported | A/V and USB data from RX
RS-232 1x RS-232: 4-pin Phoenix | Shared with 12v DC input

Compatible with WyreStorm TS-280 touchscreen via 4-pin phoenix port (only when using PoH)

HDCP Pass-through, 2.3 Supported
EDID Pass-through, from RX
Consumer Electronics Control (CEC) One-way display trigger to RX
Auto Low Latency Mode (ALLM) Supported
Variable Refresh Rate (VRR) Supported
Power
Power Supply 12V DC 1A (not included)
Max Power Consumption 7.8W
Power-over-HDBaseT (PoH) Supported, 1-way from RX
Local Power Supply Input 4-pin phoenix
Environmental
Operating Temperature 0 to + 45°C (32 to + 113 °F), 10% to 90%, non-condensing
Storage Temperature -20 to +70°C (-4 to + 158 °F), 10% to 90%, non-condensing
Maximum BTU 2.29 BTU/hr
Dimensions and Weight
  SW-130-TX-UK SW-130-TX-US
Installation In-wall, 2-gang In-wall, 2-gang
Height 86mm/3.38in 105mm/4.13in
Width 146mm/5.74in 89mm/3.5in
Depth 38mm/1.55in 38mm/1.55in
Weight 0.27Kg/0.60lbs 0.3Kg/0.66lbs
Regulatory
Safety and Emission CE | FCC | RoHS | RCM | EAC

Copyright © 2020 WyreStorm Technologies | wyrestorm.comSW-130-TX-Ux Quickstart Guide | 200326

report this ad

UK: +44 (0) 1793 230 343 | ROW: 844.280.WYRE (9973)[email protected]

References

[xyz-ips snippet=”download-snippet”]