YAMAHA VXS Series Surface Mount Speaker Owner’s Manual

YAMAHA VXS Series Surface Mount Speaker Owner’s Manual

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE PROCEEDING

Please keep this manual in a safe place for future reference.

WARNING

Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical shock, short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following:

Do not open

This device contains no user-serviceable parts. Do not open the device or attempt to disassemble the internal parts or modify them in any way. If it should appear to be malfunctioning, discontinue use immediately and have it inspected by qualified Yamaha service personnel.

Location

Do not place the product in a location where it may be exposed to smoke or oil vapors, or where any of its parts might deteriorate and cause it to fall and result in injury.

CAUTION

Always follow the basic precautions listed below to avoid the possibility ofphysical injury to you or others, or damage to the device or other property.These precautions include, but are not limited to, the following:

Location

Do not place the device in an unstable position where it might accidentally fall over.
Do not place the device in a location where it may come into contact with corrosive gases or salt air. Doing so may result in malfunction.
Do not place the device where it is always exposed to water. Doing so may result in malfunction.
Do not place the device where it is exposed to oil. Doing so may result malfunction.
Construction work should be carried out in accordance with construction related law and always by a professional constructor. If the device installation requires construction work, make sure to observe the following precautions.
- Choose mounting hardware and an installation location that can support the weight of the device.
- Avoid locations that are exposed to constant vibration.
- Use the required tools to install the device.
- Inspect the device periodically.

Connections

Before connecting the device to a power amplifier, turn off the power for all devices. Before turning the power on or off for all devices, set all volume levels to minimum.
Use only speaker cables for connecting speakers to the speaker connectors. Use of other types of cables may result in fire.

Maintenance

Do not wipe the outer packaging with benzine, thinner, or synthetic detergent and do not use electrical contact cleaner. These may damage the outer packaging and dissolve the parts.

Handling caution

Avoid inserting or dropping foreign objects (paper, plastic, metal, etc.) into holes of the grille. If this happens, have the device inspected by qualified Yamaha service personnel.
Do not operate the device if the sound is distorting. Prolonged use in this condition could cause overheating and result in fire.
When choosing a power amplifier for use with this device, make sure that the output power of the amplifier is lower than the power capacity of this device (see SPECIFICATIONS).Even if the output power of the amplifier is lower than the power capacity of this device (PGM), use of excessive input signals resulting in clipping may cause damage to the device.Malfunction or fire may occur especially when the following sounds or noises are generated:
- feedback, when using a microphone
- continuous and extreme volume sound from a musical instrument
- extreme continuous distorted sound
- noise caused by plugging/unplugging the cable while the amplifier is turned on.

NOTICE

To avoid the possibility of malfunction/damage to the product or damage to other property, follow the notices below.

Handling and Maintenance

Do not place vinyl, plastic or rubber objects on the device, since this might discolor the panel.
When cleaning the device, use a dry and soft cloth. Do not use paint thinners, solvents, cleaning fluids, or chemical-impregnated wiping cloths.
Condensation can occur in the device due to rapid, drastic changes in ambient temperature-when the device is moved from one location to another, or air conditioning is turned on or off, for example. Using the device while condensation is present can cause damage. If there is reason to believe that condensation might have occurred, leave the device for several hours until the condensation has completely dried out.
Be sure to observe the amplifier’s rated load impedance (see SPECIFICATIONS), particularly when connecting speakers in parallel. Connecting an impedance load outside the amplifier’s rated range can damage the amplifier.
When connecting the speakers with high impedance, be sure that the output total of each speaker does not exceed the rated output of the power amplifier.
When using a high-impedance speaker connection, make sure the audio signal is passed through an 80 Hz or above high-pass filter before being input to the speakers. For VXS5/VXS5W, UL Listing is void without this connection.
ABOUT THE PROTECTION CIRCUITThis speaker system has an internal protection circuit that shuts off the speaker unit when an excessive input signal is applied.If the speaker unit emits no sound, reduce the volume level of the amplifier immediately.The sound will return automatically in several seconds.
Place the speaker on a flat and smooth surface.
Do not place the speaker on the ground with the grille faced down.
Do not touch the speaker driver unit.

About This Manual

The illustrations as shown in this manual are for instructional purposes only, and may appear somewhat different from those on your device.

Yamaha cannot be held responsible for damage caused by improper use or modifications to the device.

Information for Users on Collection and Disposal of Old Equipment

This symbol on the products, packaging, and/or accompanying documents means that used electrical and electronic products should not be mixed with general household waste.

For proper treatment, recovery and recycling of old products, please take them to applicable collection points, in accordance with your national legislation and the Directives 2002/96/EC.

By disposing of these products correctly, you will help to save valuable resources and prevent any potential negative effects on human health and the environment which could otherwise arise from inappropriate waste handling.

For more information about collection and recycling of old products, please contact your local municipality, your waste disposal service or the point of sale where you purchased the items.

[For business users in the European Union]If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information.

[Information on Disposal in other Countries outside the European Union]This symbol is only valid in the European Union. If you wish to discard these items, please contact your local authorities or dealer and ask for the correct method of disposal.

UNPACKING

Unpack the contents and confirm that all the following items are included.

Speaker × 2
Bracket base × 2
Mounting bracket × 2
Bracket cover × 2
Screw for attaching the mounting bracket × 4 (VXS8/VXS8W: M6, VXS5/VXS5W: M5)
Stopper screw × 2 (M3, VXS8/VXS8W only)
Bolt with hexagon hole × 2
Safety wire × 2Terminal cover × 2
Safety pin × 2
Hexagon wrench × 1
Owner’s Manual (this manual)Screws/bolts to fasten the bracket base onto the wall/ceiling and speaker cables are not included.

SPECIFICATIONS

	VXS8/VXS8W	VXS5/VXS5W
Type	2-way, Bass-reflex
Component	LF	8″ (20 cm) Cone driver	5-1/4″ (13 cm) Cone driver
HF	1″ (2.5 cm) Soft dome tweeter	3/4″ (2 cm) Soft dome tweeter
Coverage angle (500 Hz – 4 kHz on average)	100° H × 100° V	120° H × 120° V
Nominal impedance	8 Ω
Power rating	NOISE	90 W	75 W
PGM	180 W	150 W
MAX	360 W	300 W
Sensitivity (1W, 1m) *1	91 dB SPL	89 dB SPL
Maximum SPL (Calculated, 1m) *2	117 dB SPL	114 dB SPL
Frequency range (-10 dB) 1, 3	51 Hz – 20 kHz	62 Hz – 20 kHz
Crossover frequency	2.8 kHz	3 kHz
Connector	Euroblock (4 pin) × 1 (input: +/-, loop-thru: +/-)Max. wire size 12 AWG (2.5 mm²)
Transformer taps	70 V	60 W, 30 W, 15 W, 7.5 W	30 W, 15 W, 7.5 W, 3.8 W
100 V	60 W, 30 W, 15 W	30 W, 15 W, 7.5 W
Overload protection	Full-range power limiting to protect network and transducers
Magnetically shielded	No
Dust and water resistant *4	IP35
Enclosure	Shape	Rectangle
Cabinet material	Polypropylene
Baffle material	Polypropylene
Grille material	Powder coated perforated aluminum (t=1 mm) Aperture ratio: 51%
Finish	VXS8/VXS5: Black (Not painted, approximate value: Munsell N3)VXS8W/VXS5W: White (Not painted, approximate value: Munsell 9.3)
Dimensions (Speaker only) (W × H × D in vertical cabinet orientation)	278 × 430 × 239 mm	176 × 280 × 163 mm
Net weight (Speaker only, 1 piece)	7.2 kg	3.3 kg
Packaging	Packaged in pair

Half-space (2π)
Calculated based on power rating and sensitivity, exclusive of power compression.
When connecting with low impedance
IP34 when installing the speaker to the ceiling vertically.

The contents of this manual apply to the latest specifications as of the printing date. Since Yamaha makes continuous improvements to the product, this manual may not apply to the specifications of your particular product. To obtain the latest manual, access the Yamaha website then download the manual file. Since specifications, equipment or separately sold accessories may not be the same in every locale, please check with your Yamaha dealer.The dimensions are shown overleaf.

INSTALLING THE SPEAKERS

Install the speakers onto the wall/ceiling with the supplied brackets. Ensurethat the wall/ceiling is sufficiently strong.Illustrations in this manual are for the VXS5. The installation method is the same for other models.

Pre-installation (Preparation of the cable)

Use stranded wire for cables attached to the Euroblock connector. Strip their insulation as shown in the figure and connect them.

NOTE

Do not plate stranded wires by solder. Doing so will cause the wire to break.

An installed speaker is shown below. Install the bracket base and attach themounting bracket as shown.

NOTE

When installing the speaker to the ceiling with the grille parallel to the ground, install the speaker horizontally.
When installing the speaker to the ceiling, be sure to install the bracket base with its shaft facing horizontally, and not inclined to the ground.
Mounting bracket is made to not turn left or right when installing the speaker to the ceiling.

INSTALL THE BRACKET BASE ONTO THE WALL /CEILING

Put the bracket base onto the wall/ceiling and mark the position for the screws/bolts and cables. The diameter of the screw/bolt holes at the four corners is M6, and speaker cables hole at the center is ø11 mm.
Make holes through the wall/ ceiling for the bolts and cables, as required, and feed the bolts and cables from the amplifier through the holes, as shown.
Install the bracket base onto the wall/ceiling. Make sure to fasten four corners of the bracket base.
Pass cables through the gap at the lower part of the bracket cover, and put the bracket cover on the bracket base.NOTE If you want to adjust the slack of cables last, the bracket cover can be attached after step 5-6.

CONNECT THE WIRING TO THE CONNECTOR

Remove the Euroblock connector.
After loosening the terminal screws of the Euroblock connector with a flat-blade screwdriver, insert the cable into each terminal and tighten the screws. Make sure that cables cannot be pulled out.

NOTE

Use a flat-blade screwdriver with a blade less than 3 mm (0.1 in.). Use a flat-blade screwdriver with a blade less than 3 mm (0.1 in.).Less than 3 mm (0.1 in.)

There are two acceptable wiring methods.

CAUTION

When connecting with low impedance, take note of the combined resistance.

Using Loop-Through Terminals

For this method, cables are connected from terminals 1 and 4 to the subsequent speaker. If the Euroblock connector is disconnected from a speaker, all subsequent speakers will not work. This can be useful to identify which speaker has a problem.

Paralleling Input Terminals

For this method, cables are connected to terminals 2 and 3 of each speaker. Since the cables are connected via Euroblock connectors, subsequent speakers can work even if a problem occurs with a speaker.

SET THE LINE VOLTAGE/IMPEDANCE AND POWER

Select the line voltage/impedance (100V/70V/8Ω) and power tap for 100V/ 70V line distributed system, by rotating the tap selector switch on the rear side of the speaker with a flat-blade screwdriver.

Illustration indicates the setting at 30 W for 100 V line and 15 W for 70 V line.

CAUTION

The “X” position should not be selected. The 8Ω position should be selected for 8Ω audio systems only. If the setting is incorrect, it may cause malfunction of the speaker and amplifier.
Make sure the amplifier is switched off before operating the tap selector switch.

ATTACH THE MOUNTING BRACKET AND SAFETY WIRE

Attach the mounting bracket and safety wire to the speaker. Use the supplied screws to attach the mounting bracket. The way to attach the mounting bracket depends on the orientation of the speaker (vertical or horizontal).Vertical installationHorizontal installation
Set the desired vertical angle of the speaker.Loosen the angle adjustment bolt with the supplied hexagon wrench, adjust the angle of the speaker, and tighten the angle adjustment bolt to fix the speaker (indication of torque: 8 N·m).

NOTE

Guide marked on the mounting bracket is every 10°.
(VXS8/VXS8W only) When installing the speaker to the wall with a vertical angle of 30° or less, attach the supplied stopper screw.

INSTALL THE SPEAKER TO THE BRACKET BASE AND FIX THE CABLE

Install the mounting bracket to the bracket base.
Attach the safety pin.Be sure to attach the safety pin to prevent the mounting bracket from falling.NOTE: The safety pin can be attached from either side of the mountingbracket depending on the angle of the speaker.
Plug the Euroblock connector into the socket in the speaker
Attach the terminal cover.
If installing the speaker to the wall) turn the speaker horizontally to set the angle.
Make sure the mounting bracket is seated against the bracket base, then tighten the supplied bolt (indication of torque: 6.5 N·m).NOTE
- When installing the speaker to the ceiling in particular, make surethe mounting bracket is seated against the bracket base.
- The bolt with hexagon hole can be attached from either side of the mounting bracket (left or right) depending on the angle of the speaker.
Install the safety wire to the wall/ceiling.

CAUTION

Make sure to take measures to prevent the speaker from falling down in the event of a installation failure.
When installing the safety wire to the wall, install it higher than the wire’s attachment point on the speaker, with as little slack as possible.
If the safety wire is too short, prepare another wire appropriate for the speaker weight and installation conditions. If the wire is too long, should the speaker fall, the wire may snap as a result of too much strain.

Important Notice: Guarantee Information for customers in EEA* and Switzerland

For detailed guarantee information about this Yamaha product, and Pan-EEA” and Switzerland warranty service, please either visit the website address below (Printable file is available at our website) or contact the Yamaha representative office for your country. * EEA: European Economic Area.

https://europe.yamaha.com/warranty/

ADDRESS LIST

NORTH AMERICA

CANADA

Yamaha Canada Music Ltd.135 Milner Avenue, Toronto, Ontario, MIS 3R1, CanadaTel: +1-416-298-1311

U.S.A.

Yamaha Corporation of America6600 Orangethorpe Avenue, Buena Park, CA 90620, U.S.A.Tel: +1-714-522-9011

CENTRAL & SOUTH AMERICA

MEXICO

Yamaha de Mexico, S.A. de C.V.Av. Insurgentes Sur 1647 Piso 9, Col. San Jose Insurgentes, Delegation Benito Juarez, Mexico, D.F., C.P. 03900, MexicoTel: +52-55-5804-0600

BRAZIL

Yamaha Musical do Brasil Ltda.Praca Professor Jose Cannes, 40, Cjs 21 e 22, Brooklin Paulista Novo CEP 04571-100— Sao Paulo — SP, BrazilTel: +55-11-3704-1377

ARGENTINA

Yamaha Music Latin America, S.A.,Sucursal Argentina Olga Cossettini 1553, Piso 4 Norte, Madero Este-C1107CEK, Buenos Aires, ArgentinaTel: +54-11-4119-7000

PANAMA AND OTHER LATIN AMERICAN/CARIBBEAN REGIONS

Yamaha Music Latin America, S.A.Edif. Torre Banco General, Piso 7, Urbanization Marbella, Calle 47 y Aquilino de la Guardia, Ciudad de Panama, Republica de PanamaTel: +507-269-5311

EUROPE

THE UNITED KINGDOM/IRELAND

Yamaha Music Europe GmbH (UK)Sherboume Drive, Tilbrook, Milton Keynes, MK7 8BL, U.K.Tel: +44-1908-366700

GERMANY

Yamaha Music Europe GmbHSiemensstrasse 22-34, 25462 Rellingen, GermanyTel: +49-4101-303-0

SWITZERLAND/LIECHTENSTEIN

Yamaha Music Europe GmbH, Branch Switzerland in ThalwilSeestrasse I8a, 8800 Thalwil, SwitzerlandTel: +41-44-3878080

AUSTRIA/BULGARIA/ CZECH REPUBLIC/HUNGARY/ ROMANIA/SLOVAKIA/SLOVENIA

Yamaha Music Europe GmbHBranch AustriaSchleiergasse 20, 1100 Wien, AustriaTel: +43-1-60203900

POLAND

Yamaha Music Europe GmbHSp.z o.o. Oddzial w Po!seeul. Wielicka 52, 02-657 Warszawa, PolandTel: +48-22-880-08-88

MALTA

Olimpus Music Ltd.

Valletta Road, Mosta MST9010, Malta Tel: +356-2133-2093

NETHERLANDS/BELGIUM/ LUXEMBOURG

Yamaha Music Europe Branch BeneluxClarissenhof 5b, 4133 AB Vianen, The NetherlandsTel: +31-347-358040

FRANCE

Yamaha Music Europe7 rue Ambroise Croizat, Zone d’activites de Pariest, 77183 Croissy-Beaubourg, FranceTel: +33-1-6461-4000

ITALY

Yamaha Music Europe GmbH,Branch ItalyVia Tinelli N.67/69 20855 Germ di Lesmo (MB), ItalyTel: +39-039-9065-1

SPAIN/PORTUGAL

Yamaha Music Europe GmbH lberica, Sucursal en EspanaCtra. de la Coruna km. 17,200, 28231 Las Rozas de Madrid, SpainTel: +34-91-639-88-88

GREECE

Philippos Nakas S.A. The Music House19th klm. Leof. Lavriou 190 02 Peania — Attiki, GreeceTel: +30-210-6686168

SWEDEN/FINLAND/ICELAND

Yamaha Music Europe GmbH Germany filial ScandinaviaJA Wettagrensgata I, 400 43 Goteborg, SwedenTel: +46-31-89-34-00

DENMARK

Yamaha Music Denmark, Fillial of Yamaha Music Europe GmbH, Tysklaud Generatorvej 8C, ST. TH. , 2860 Soborg, DenmarkTel: +45-44-92-49-00

NORWAY

Yamaha Music Europe GmbH Germany-Norwegian Branch Grini Nzeringspark I, 1332 Cisterns, NorwayTel: +47-6716-7800

CYPRUS

Yamaha Music Europe GmbHSiemensstrasse 22-34, 25462 Rellingen, GermanyTel: +49-4101-303-0

RUSSIA

Yamaha Music (Russia) LLC.Room 37, entrance 7, bld. 7, Kievskaya street, Moscow, 121059, RussiaTel: +7-495-626-5005

OTHER EUROPEAN REGIONS

Yamaha Music Europe GmbHSiemensstrasse 22-34, 25462 Rellingen, GermanyTel: +49-4101-3030

AFRICA

Yamaha Music Gulf FZEJAFZA-16, Office 512, P.O.Box 17328, Jebel All FZE, Dubai, UAETel: +971-4401-1500

MIDDLE EAST

TURKEY

Yamaha Music Europe GmbH

Merkezi Almanya Tfirkiye Istanbul Subesi Mor Sumbul Sokak Varyap Meridian Business 1.Blok No:1 113-114-115 Bati Atasehir Istanbul, TurkeyTel: +90-216-275-7960

OTHER REGIONS

Yamaha Music Gulf FZEJAFZA-16, Office 512, P.O.Box 17328, Jebel All FZE, Dubai, UAETel: +971-4-801-1500

ASIA

THE PEOPLE’S REPUBLIC OF CHINA

Yamaha Music & Electronics (China) Co.,Ltd.2F, Yunhedasha, 1818 Xinzha-lu, Jingan-qu, Shanghai, ChinaTel: +86400-051-7700

INDIA

Yamaha Music India Private LimitedP-401, JMD Megapolis, Sector-48, Sohna Road, Gurugram-122018, Haryana, IndiaTel: +91-124-485-3300

INDONESIA

PT Yamaha Musik Indonesia DistributorYamaha Music Center Bldg. Jalan Jend. Gatot Subroto Kay. 4, Jakarta 12930, IndonesiaTel: +62-21-520-2577

KOREA

Yamaha Music Korea Ltd.I IF, Prudential Tower, 298, Gangnam-daero, Gangnatn-gu, Seoul, 06253, Korea Tel: +82-2-3467-3300

MALAYSIA

Yamaha Music (Malaysia) Sdn. Bhd.No.8, Jalan Perbandaran, Kelana Jaya, 47301 Petaling Jaya, Selangor, MalaysiaTel: +60-3-78030900

SINGAPORE

Yamaha Music (Asia) Private Limited Block 202 Hougang Street 21, #02-00, Singapore 530202, SingaporeTel: +654740-9200

TAIWAN

Yamaha Music & Electronics Taiwan Co.,Ltd. 2E, No.1, Yuandong Rd., Banqiao Dist., New Taipei City 22063, Taiwan (R.O.C.)Tel: +886-2-7741-8888

THAILAND

Siam Music Yamaha Co., Ltd. 3, 4, 15, 16th Fl., Siam Motors Building, 891/1 Rama 1 Road, Wangmai, Pathumwan, Bangkok 10330, ThailandTel: +66-2215-2622

VIETNAM

Yamaha Music Vietnam Company Limited15th Floor, Nam A Bank Tower, 201-203 Cacti Mang Thang Tam St., Ward 4, Dist.3, Ho Chi Minh City, VietnamTel: +84-8-3818-1122

OTHER ASIAN REGIONS

http://asia.yamaha.com/

OCEANIA

AUSTRALIA

Yamaha Music Australia Pty. Ltd.Level 1, 80 Market Street, South Melbourne,VIC 3205, AustraliaTel: +61-3-9693-5111

REGIONS AND TRUST TERRITORIES IN PACIFIC OCEAN

Imp://asia.yamaha.com/

Head Office/Manufacturer: Yamaha Corporation 10-1, Nakazawa-cho, Naka-ku, Hamamatsu, 430-8650, Japan (For European Countries) Importer: Yamaha Music Europe GmbH Siemensstrasse 22-34, 25462 Rellingen, Germany