Z-WAVE PLUS MP21ZS SmartPlug Dimmer
Federal Communications Commission (FCC) Statement
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and(2) this device must accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on,the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.IC Caution:This device complies with Industry Canada licence-exempt RSS standard(s).Operation is subject to the following two conditions:(1) this device may not cause interference, and(2) this device must accept any interference, including interference that may cause undesired operation of the device.
WARRANTY
Evalogik Products warrants this product to be free from manufacturing defects for a period of two years from the original date of consumer purchase. This warranty is limited to the repair or replacement of this product only and does not extend to consequential or incidental damage to other products that may be used with this product.This warranty is in lieu of all other warranties, expressed or implied. Some states do not allow limitations on how long an implied warranty lasts or permit the exclusion or limitation of incidental or consequential damage, so the above limitations may not apply to you.This warranty gives you specific rights, and you may also have other rights which vary from state to state. if the unit should prove defective within the warranty period.
SPECIFICATIONS
Model: MP21ZSPower: 120 VAC, 60 Hz.Signal (Frequency): 908.42 MHZ.Maximum load for outlet 500W ResistiveMaximum load for the Z-Wave™ controlled outlet:Range: Up to 100 feet line of sight between the Wireless Control and the closest Z-Wave™ receiver module.Operating Temperature Range: 32-104° F (0-40° C)Specifications subject to change without notice due to continuing product improvementWebsite: www.nie-tech.com
Warning:
- RISK OF FIRE
- RISK OF ELECTRICAL SHOCK
- RISK OF BURNS
- CONTROLLING APPLIANCES:
- EXERCISE EXTREME CAUTION WHEN USING Z-Wave™ DEVICES TO CONTROL APPLIANCES. OPERATION OF THE Z-Wave™ DEVICE MAY BE IN A DIFFERENT
- MAY OCCUR IF THE WRONG BUTTON ON THE REMOTE IS PRESSED. Z-Wave™ DEVICES MAY AUTOMATICALLY BE POWERED ON DUE TO TIMED EVENT PROGRAMMING.
- DEPENDING UPON THE APPLIANCE, THESE UNATTENDED OR UNINTENTIONAL OPERATIONS COULD POSSIBLY RESULT IN A HAZARDOUS CONDITION. FOR THESE REASONS, WE RECOMMEND DO NOT RETURN THIS PRODUCT TO THE STORE
- DO NOT USE Z-Wave™ DEVICES TO CONTROL ELECTRIC
- HEATERS OR ANY OTHER APPLIANCES WHICH MAY PRESENT A HAZARDOUS CONDITION DUE TO UNATTENDED OR UNINTENTIONAL OR AUTOMATIC POWER ON CONTROL.
Introduction:
This product can be operated in any Z-Wave network with other Z-Wave Plus™ certified devices from other manufacturers.All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network. Each module is designed to act as a repeater, which will re-transmit a radio frequency (RF) signal by routing the signal around obstacles and radio dead spots to ensure that the signal is received at its intended destination.MP21ZS is a security enabled Z-Wave Plus™ device. A security Enabled Z-Wave Plus™ Controller must be used in order to fully utilize the product. The Device Type of the MP21ZS is on/off power switch.The Role Type of the MP21ZS is Always On Slave Role Type
Key Features:
- Remote ON/OFF control via the Z-Wave™ controller
- Manual ON/OFF control with the front panel push button
- Support Association Group and Auto Report switch status
- Support firmware upgrades via Over-the-air (need Gateways support)
- Support Scenes
Product Overview:
- AC plug
- Z-Wave controlled outlet
- ON/OFF/PROG Push button/ Status LED
Key function description
- Press the button to turn the output ON or OFF
- quickly press 3x Button: ADD(inclusion) (only if switch is not included in network)quickly press 3x Button: Remove( exclusion)
- Press click Z-Wave button 3 times quickly, and hold for at least 10 seconds at the third time to restore the device to the factory(Node: Please use this procedure only when the network primary controller is missing or otherwise inoperable.)
- Tap A(1x/2x/3x/4x/5x/Hold/Release) Activate the scene.
Adding Your Device To A Hub
The device support two methods of inclusion,When using a Z-Wave Plus™ certified controller choose Network Wide Inclusion or SmartStart, Network Wide Inclusion To A Z-Wave™ Network
- Refer to your primary controller instructions to process the inclusion / exclusion setup procedure.
- When prompted by your primary controller, click the button three times in one second.
The device is compatible with SmartStartSmartStart enabled products can be added into a Z-Wave network by scanning the Z-Wave™ QR Code found on the top of the outlet or the back of the box with a controller providing SmartStart inclusion. No further action is required and the SmartStart product will be added automatically within 10 minutes of being switched on and in the network vicinity.
QR CODE
the QR code are sticked to the side of the case, DSK is included in the QR code. DSKThe DSK code can be found on the DSK label which is attached on the packaging box.
Command Class
Support for Association Groups
MP21ZS supports 3 association groups. Group 1 supports 1 node ID, Group 2 and Group 3 Supports maximum of 5 node ID’s Association group_1:Z-Wave™ Plus Lifeline
Association group_1 is default to associate with the primary controller (Gateway/Hub/Controller) for MP21ZS Status change report,MP21ZS will trigger AUTO report function if the Switch status had been changed.(ex. Switch Multilevel Report/Indicator Report/Central Scene Notification/ Device Reset Locally Notification) Association group_2:basic set command on/off control)
When the output of the MP21ZS is changed, On (0xFF) or Off (0x00). The MP21ZS will automatically send out a related basic set command. On (0xFF) or Off (0x00) to its associated group.Association group_3:basic set command on/off control
When the output of the MP21ZS is changed, On (0xFF) or Off (0x00). The MP21ZS will automatically send out a related basic set command. On (0xFF) or Off (0x00) to its associated group.
Restoring Factory Defaults
MP21ZS is removed from the network and will be restored to the factory settingAll Configuration Parameters values and Association information will be restored to factory default settings and excluded from the network. Manual Reset: Press click Z-Wave button 3 times quickly, and hold for at least 10 seconds at the third time to restore the device to the factory Remark : All the setting and data will be permanently deleted.Please use this procedure only when the network primary controller is missing or otherwise inoperable.
References
[xyz-ips snippet=”download-snippet”]