Zeblaze Hybrid Smartwatch User Manual

Zeblaze Hybrid Smartwatch User Manual


Hardware configuration

Quartz movement: AL35EQuartz battery: SR626SWProgramme: nRF51802Bluetooth: BT4.0Display: OLED 0.49″ (64×32)3D Sensor: SC7A20Heart Sensor: EM7028Motor: Flat 0820Programme battery: 90mAh


BT distance: 5 – 10m (Open space)Quartz standby: 3 yearsProgramme standby: About 7 days (Depending on frequency of use)Waterproof level: 5ATMButton life: 100K timesTouch life: 100K times

Electrical parameter

Operating voltage: 3.8VWorking current: 100uA (display off), 15mA (display on)Standby current: 30 – 80uA (All function turned off)Vibration current: 5mAMotor frequency: 12000

Material process

Watch case: Carbon fiber + PCTop ring: Zinc alloyWatch glass: Double glassButton: 316L stainless steelStrap: Silicone Strap buckle: 316L stainless steelBottom cover: 316L stainless steelWatch case size: Φ45.0 x 16.5mmAdapter strap: 20.0mm (strap width)Suitable: 150 – 205mm (wrist perimeter)Unit weight: 58.0g

Dear user:

Thank you for your favor. It’s not only a traditional quartz watch, but also a Hybrid smart watch integrating health&sport, mobile phone assistant and smart OLED display. For better use of this watch, please read this Operation Guide before using it. All illustrations for this Operation Guide are for reference only and products are subject to the actual ones.

Watch hand alignment

Watch hand timing start- up

Remove the crown stop card and push crown into the watch body, then watch hand will start- up.

Adjust the time

When the watch crown is pulled out, and turn it to adjus time. (Note: watch display time automatic synchronization APP pairing mobile time, see related chapter introduction)

Replacement of quartz battery

The quartz core of the watch has its own button battery, which can be used for more than 3 years. When you find that the watch hand is stopped, please change to the same type button battery in time.

Boot and charge

Boot instruction

This watch does not support ‘power on/off’ operation. the smart module will automatically turn on when the polymer battery power is >0% and turn off when power is 0%.

How to charge

  1. The attached accessories have a charging seat and USB cable, which should be used with standard charger (within 5V/ 2A) or standard USB power supply. Connect the charging seat and charger (or USB) with the USB cable, and then connect the charger to a power outlet.
  2. The charging base adopts 360 polarless charging design.
  3. It takes about 2-3 hour for the watch to be fully charged, and when the charging indication shows 100%, indicating full charge.

APP download and install

In order to better use the smart functions of this watch.You need to install APP on your smartphone. iPhone system needs to be IOS 8.2 or above, Android mobile system needs to be Android 4.3 or above.

QR scanning installation

This APP supports Apple mobile phone or Android mobile phone, please scanning the following QR to download and install APP.

Search and install

iPhone: search and install “Comfit” on App Store.Android phone: search and install “Comfit” on Google play.Android (China): search and install “Comfit” on App Store.

App binding watches

Step ①: Access to the APP, register your user account.Step ②: Turn on the watch and BT, and take it close to your mobile phone.Step ③: Access to the APP footer menu “Mine” and click “Comfit device” ; wait for the mobile phone: Search for “HYBRID” and click to start BT connection.Step ④: After the successful connection, the app automatically enters the “Comfit device” interface; click “Looking for device” , If the watch vibrate to verify the success of the watch and the mobile phone binding.

More operation instructions

In order to update the instructions in time, we arranged “more operation instructions” in the menu of APP. For further understanding of product operation, please go to “Mine – Help” of APP. (Note: Before reading “Help”, the watch and mobile APP must be bound first)

Zeblaze Hybrid Smartwatch User Manual – Zeblaze Hybrid Smartwatch User Manual –

[xyz-ips snippet=”download-snippet”]