Quick Start GuideTELEPORT GLT/GLRHigh-Performance Active Guitar Signal Transmitter for Long Cable Run Systems
Connection
Getting Started
- Connect the included power adaptor to the GLT power socket.
- Connect your guitar to the GLT ¼” input via a standard instrument cable.
- Connect a balanced XLR cable from the GLT output to the GLR input.
- With the amplifier turned off or in standby mode, connect a standard instrument cable from the GLR output to your amp’s input.
- Power on your amplifier.
- Move the ground switch on the GLR to the LIFT position if the grounding noise is audible.
- Adjust the DRAG control to simulate the loading that occurs when you connect directly into an amp at a close distance. More drag will simulate a longer cable.
Puesta en Marcha
- Conecte el adaptador de corriente incluido a la toma de corriente GLT.
- Conecte su guitarra a la entrada GLT de ¼ “mediante un cable de instrumento estándar.
- Conecte un cable XLR balanceado desde la salida GLT a la entrada GLR.
- Con el amplificador apagado o en modo de espera, conecte un cable de instrumento estándar desde la salida GLR a la entrada de su amplificador.
- Encienda su amplificador.
- Mueva el interruptor de tierra en el GLR a la posición de ELEVACIÓN si el ruido de conexión a tierra es audible.
- Ajuste el control DRAG para simular la carga que se produce cuando se conecta directamente a un amplificador a corta distancia. Más arrastre simulará un cable más largo.
Specifications
| GLR | GLT | |
| Input | ||
| Connector | XLR female, balanced | ¼” TS, unbalanced |
| Impedance | 180 kΩ | Adjustable 22 kΩ to
>1 MΩ |
| Max. input level | — | +10 dBu @ 1 kHz |
| Output | ||
| Connector | ¼” TRS, unbalanced | XLR male, balanced |
| Impedance | 200 kΩ | 2 kΩ |
| Max. output level | — | +10 dBu @ 1 kHz |
| System | ||
| Frequency response | 10 Hz to 35 kHz(±3 dB) | 10 Hz to 26 kHz (± 3 dB) |
| THD + N (distortion) | 0.0015% @ 1 kHz,0 dBu | 0.05% @ 1 kHz, 0 dBu |
| Signal-to-noise ratio | 110 dB @ 1 kHz, 0 dBu | 90 dB @ 1 kHz, 0 dBu |
| CMRR | 62 dB typical | — |
| Power requirement | Passive | 12 V DC, 150 mA |
| Physical | ||
| Dimensions (H x W x D) | 64 x 118 x 112 mm (2.5 x 4.6 x 4.4″) | |
| Weight | 0.43 kg (0.9 lbs) | 0.5 kg (1.1 lbs) |
LEGAL DISCLAIMER
Music Tribe accepts no liability for any loss which may be suffered by any person who relies either wholly on or in part upon any description, photograph, or statement contained herein. Technical specifications, appearances, and other information are subject to change without notice. All trademarks are the property of their respective owners. Midas, Klark Teknik, Lab Gruppen, Lake, Tannoy, Turbosound, TC Electronic, TC Helicon, Behringer, Bugera, Oberheim, Auratone, Aston Microphones, Aston Microphones, and Coolaudio are trademarks or registered trademarks of Music Tribe Global Brands Ltd. © Music Tribe Global Brands Ltd. 2021 All rights reserved.
LIMITED WARRANTY
For the applicable warranty terms and conditions and additional information regarding Music Tribe’s Limited Warranty, please see complete details online at musictribe.com/warranty.
FEDERAL COMMUNICATIONS COMMISSION COMPLIANCE INFORMATIONTC Electronic
TELEPORT GLT/GLR
| Responsible Party Name: | Music Tribe Commercial NV Inc. |
| Address: | 5270 Procyon Street,Las Vegas NV 89118,United States |
| Phone Number: | +1 702 800 8290 |
TELEPORT GLT/GLR
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
report this adOperation Ambient Temperature up to 45°CImportant information:Changes or modifications to the equipment not expressly approved by Music Tribe can void the user’s authority to use the equipment.
Hereby, Music Tribe declares that this product is in compliance with Directive 2014/35/EU, Directive2014/30/EU, Directive 2011/65/EU, and Amendment 2015/863/EU, Directive 2012/19/EU, Regulation 519/2012 REACH SVHC and Directive 1907/2006/EC.Full text of EU DoC is available at https://community.musictribe.com/EU Representative: Music Tribe Brands DK A/SAddress: Ib Spang Olsens Gade 17, DK – 8200 Aarhus N, Denmark
[xyz-ips snippet=”download-snippet”]