Aeotec Siren 6 User Manual

Aeotec Siren 6 User Manual

Aeotec Siren 6.

Aeotec Siren 6 was developed to work as a doorbell or siren via Z-Wave Plus. It is powered byAeotec’s Gen5 technology and features Z-Wave S2.

Get to Know your Siren.

Pre-loaded Tones.

Tone #

 Name

Use

1

 Ding Dong

Doorbell

2

 Ding Dong Tubular Bell

Doorbell

3

 Traditional Apartment Buzzer

Doorbell

4

 Electric Apartment Buzzer

Doorbell

5

 Westminster Chimes (Hearing Enhanced)

Doorbell

6

 Chimes (Hearing Enhanced)

Doorbell

7

 Cuckoo (Hearing Enhanced)

Doorbell

8

 Traditional Bell

Doorbell

9

 Smoke Alarm (Low)

Safety

10

 Smoke Alarm (High)

Safety

11

 Fire Evacuation Buzzer

Safety

12

 CO Alarm

Safety

13

 Klaxon

Safety

14

 Klaxon (Deep)

Safety

15

 Warning Tone

Safety

16

 Tornado Siren

Safety

17

 Alarm

Security

18

 Deep Alarm Tone

Security

19

 Alarm (Archangel tone)

Security

20

 Alarm (Shrill)

Security

21

 Digital Siren

Security

22

 Alert Series

Security

23

 Security

Misc.

24

 Clock Buzzer

Misc.

25

 Christmas Tree

Misc.

26

 Gong

Misc

27

 Single Bell Ting

Misc

28

 Tonal Pulse

Misc.

29

 Upwards Tone

Misc.

30

 Door Open

Misc.

Important safety information.

Please read this and other device guides carefully. Failure to follow the recommendations set forth by Aeotec Limited may be dangerous or cause a violation of the law. The manufacturer, importer, distributor, and / or reseller will not be held responsible for any loss or damage resulting from not following any instructions in this guide or in other materials.Keep product away from open flames and extreme heat. Avoid direct sun light or heat exposure. Siren 6 is intended for indoor use in dry locations only. Do not use in damp, moist, and / or wet locations.

Warning: to prevent possible hearing damage, test only when wearing appropriate hearing protection.

Quick Start.

Getting your Siren up and running is as simple as plugging it into a wall socket and linking it to your existing Z-Wave network. The following instructions tell you how to link your Siren to your Z-Wave network.

Install Mounting plate in the location of your choice.

  1. Affix Siren 6 Wall Mount Plate in any desired location near an outlet.a. Use 3x 20mm screws or double-sided tape.b. Lock the Siren 6 into place where the mount is installed.

Pairing your Siren 6 into your existing Z-Wave network.

  1. Power Siren 6 through the provided power adapter.
  2. Ensure that Siren 6 LED is blinking slowly.
  3. Set your Z-Wave gateway into pair / add device mode. (Refer to your Z-Wave gateway/controller instruction manual on how to set it into pair mode).
  4. Tap the Siren 6 Action Button once (quick). (If your gateway supports S2 encryption, enter the first 5 digits of the DSK into your Z-Wave gateway interface to complete S2 encrypted pairing, DSK is printed on the Siren 6 unit).
  5. If Siren 6 has successfully paired to your Z-Wave gateway, the LED on Siren 6 will emit a solid color for 30 seconds, then turn off. If in the case that the Siren 6 failed to pair, LED will continue to blink slowly.With your Siren now working as a part of your smart home, you’ll be able to configure it from your home control software. Please refer to your software’s user guide for precise instructions on configuring Siren to your needs.

Removing your Siren from a Z-Wave network.

Your Siren can be removed from your Z-Wave network at any time. It is always advised that you use your gateway to perform an unpair in order to avoid leaving phantom / failed nodes that become difficult to remove. To do so, follow the steps below:

  1. Place your gateway or controller into Z-Wave unpair or exclusion mode. (Please refer to your controller/gateway manual on how to do this)
  2. Press the Action Button 6x times in 2 seconds on your Siren.
  3. If your Siren has been successfully unpaired from your network, its LED will begin to blink slowly which indicates that it is ready to be paired again.

Test Siren 6 sound manually.

You will be able to manually test your Siren 6 unpaired or paired to a Z-Wave network, to determine if its sound is working, perform the button action listed below:

  • Press and hold Action Button down for 2-5 seconds

Safety: Test only when wearing necessary ear protection. Siren 6’s speaker emits tones up to 105dB that can cause hearing damage.

Reset your Siren.This method is not fully advised unless your gateway has failed, and you do not yet have another gateway to perform a general unpair on Siren 6.

To do this, follow the steps below:

  1. Press and hold the Action button for 20 seconds
  2. [2-5 seconds], the test siren sound will run, then stop after 5 seconds has passed.
  3. [5-20 seconds] The LED will continue to blink faster (5 to 10 seconds) and faster (10 to 20 seconds).
  4. [21 seconds and later] The LED will then quickly flash 3 times then will have LED breath in and out as you hold down the Action Button
  5. Release the Action button, and the Siren 6 will factory reset.

Low battery indicator for Button #1 – #3)

Siren 6 has 3 low battery indicators for 3 possible button slots. This will indicate if battery is low on any connected button to Siren 6.Button 1

  • LED blinks once (100ms), then no LED for 5 seconds. Repeats continuously until replacement of battery.Button 2
  • LED blinks twice (100ms), then no LED for 5 seconds. Repeats continuously until replacement of battery.Button 3
  • LED blinks thrice (100ms), then no LED for 5 seconds. Repeats continuously until replacement of battery.

To resolve the LED from blinking, you must replace the battery of your Button that is connected to Siren 6.

  1. Remove the battery of Button (based on the LED indicator above).
  2. Wait 10-20 seconds, allow the button to power cycle
  3. Replace with a new battery
  4. Tap the button once to update the battery level on Siren 6 / Doorbell 6

Upgrade Siren 6 to Doorbell 6.

You can upgrade Siren 6 to Doorbell 6 at any time, all you need is Aeotec Button which is a wireless addon button used for Siren/Doorbell 6. Siren 6/Doorbell 6 supports up to 3 Aeotec Buttons. You can learn how to pair Aeotec Button to Siren 6 in the Button manual.

Siren 6 technical specifications.

Name: Siren 6Model Number: ZW164Product Dimensions: 76 x 76 x 38.5 mmPackage Dimensions: 105 x 164 x 55 mmProduct Weight: 204 gTotal Package Weight: 275 gUPC/EAN:US: 810667024154EU: 1220000016224UK: 1220000016477AU: 1220000016217Wireless Technology: Z-Wave, 433.92 FSK.Repeater: YesBeaming: YesZ-Wave Plus: YesZ-Wave Security: S0, S2 unauthenticated, and S2 AuthenticatedZ-Wave Hardware: ZM5101Z-Wave Library Type: Enhanced 232 SlaveZ-Wave Device Type: Sound SwitchZ-Wave Role Type: Always On Slave.Smart Start Compatible: NoInput Voltage:Adapter: 5V/2ABattery: 3.7VBackup Battery:PT502035400mAhNot DetachableRechargable via power adapter4 Hours total use.Storage: 16MSensors: VibrationMax Supported Tones: 30Max Supported Buttons: 3Max Standby Power: 0.7W.Max Volume: 105dB from 5cmOperating humidity: 8% to 80%.Operating temperature:0°C to 40°C32°F to 104°F.Operating Distance:30m indoor150m outdoor

Specifications subject to change without notice due to continuing product improvement.

 

Read More About This Manual & Download PDF:

 

References

[xyz-ips snippet=”download-snippet”]

Posted

in

by

admin

Tags:

, , , ,