KLARKTEKNIK 2-Channel Active DI Box DN200 User Guide

KLARKTEKNIK 2-Channel Active DI Box DN200

DN2002-Channel Active DI Box with Extended Dynamic Range and Sum/Split Options

  1. STEREO INPUT – Connect a line-level audio source via stereo 1/8″ TRS cable. Ensure that the L/R INPUTS and LINK THRU jacks are disconnected when using the STEREO INPUT jack.
  2. PAD – Press to reduce the input signal by 20 dB for use with hot signals.
  3. EARTH – Press to separate the input and output grounds, potentially eliminating earth/ground loops between equipment on different mains supplies.
  4. L/R INPUT – Connect either balanced or unbalanced XLR or 1/4″ cables. Ensure that the 1/8″ STEREO INPUT jack is disconnected when using these inputs.
  5. 48 V LED – Lights when the unit receives sufficient phantom power. Note that the DN200 must be powered to operate correctly.Important: Although the DN200 will function as a mono device when only one channel is connected, both channels should be powered to use stereo, split, or sum modes.
  6. SUM – When engaged, the left and right inputs are summed and fed to the left and right outputs. Note that phantom power must be delivered to both output connections for dual-output operation.
  7. SPLIT – When engaged, the left input is fed to the left and right outputs. Note that phantom power must be delivered to both output connections for dual-output operation.
  8. L/R OUTPUT – Send the signals to a mixer or recording interface via balanced XLR cables. Note that the connected device must be able to provide +48 V phantom power to these connectors.
  9. LINK THRU – Send the signals to an alternate source via balanced or unbalanced 1/4″ cables. Ensure that the 1/8″ STEREO INPUT jack is disconnected when using these outputs.

Specifications

Inputs

Connectors 2 x combo XLR, 2 x 1/4″ TRS link jacks, 1/8″ stereo TRS jack
Impedance 1 MΩ (combo & link jacks balanced), 20 kΩ (combo XLR only), 500 kΩ (1/8″ stereo TRS jack unbalanced)
Max input level 28 dBu combo XLR and TRS link jacks (pad enabled), 21 dBu 1/8″ TRS jack (pad enabled)
Attenuator 20 dB pad

Outputs

Connectors 2 x 3-pin XLR
Impedance 50 Ω
Max output level 13 dBu with 10 kΩ load, 10 dBu with 600 Ω load
Min load 600 Ω

System

Noise -103 dBu, 22 Hz to 22 kHz unweighted, with input terminated by 10 kΩ resistor
Frequency response 20 Hz to 20 kHz, ±1 dB, 10 kΩ load
Distortion (THD + N) Typically <0.005% @ 1 kHz, +10 dBu
Crosstalk <100 dB @ 1 kHz, inputs terminated

Power Requirement

Voltage                            +48 V phantomCurrent consumption      <10 mA per channel

Physical

Dimensions                  118 x 63 x 142 mm (4.7 x 2.5 x 5.6″)Weight                          0.65 kg (1.43 lbs)

Note: Operation Ambient Temperature up to 45oC

LEGAL DISCLAIMER

Music Tribe accepts no liability for any loss which may be suffered by any person who relies either wholly or in part upon any description, photograph, or statement contained herein. Technical specifications, appearances and other information are subject to change without notice. All trademarks are the property of their respective owners. Midas, Klark Teknik, Lab Gruppen, Lake, Tannoy, Turbosound, TC Electronic, TC Helicon, Behringer, Bugera, Auratone and Coolaudio are trademarks or registered trademarks of Music Tribe Global Brands Ltd.© Music Tribe Global Brands Ltd. 2020 All rights reserved.

LIMITED WARRANTY

For the applicable warranty terms and conditions and additional information regarding Music Tribe’s Limited Warranty, please see complete details online at musictribe.com/warranty

report this ad

References

[xyz-ips snippet=”download-snippet”]

Posted

in

by

admin

Tags:

, , , , , , , ,