LG LED TV Owner’s Manual

Table of Contents

LED TV

ENGLISH _index

OWNER’S MANUALSafety and ReferenceLED TV** Disclaimer LG LED TV applies LCD screen with LED backlights. Please read this manual carefully before operating your set and retain it for future reference.

*MFL71753512*(2012-REV00)

TitleWarning! Safety instructionsPreparing– Lifting and moving the TV – Mounting on the Table – Mounting to the Wall – Antenna/Cable – Satellite dishStarting TV– Turning on the TV – Registering Magic Remote ControlUsing Remote Control– Using Magic Remote Control

ConnectionsTroubleshootingSpecifications– Open Source Software Notice Information – LicensesRegulatory

Before reading this manual

· Read this manual thoroughly before operating your TV, and keep it for future reference. · On the website you can download the manual including installation, using, troubleshooting, specifications, license etc and view itscontents on your PC or mobile device.

User Guide

For more information about this TV, read the USER GUIDE embedded in the product. (Depending on model) · To open the USER GUIDE [Support] [User Guide]

Separate Purchase

· Separate purchase items can be changed or modified for quality improvement without any notification. Contact your dealer to buy these items. These devices only work with certain models.· The model name or design may be changed depending on the upgrade of product functions, manufacturer’s circumstances or policies.

Note

· Product specifications or contents of this manual may be changed without prior notice due to upgrade of

product functions.

· The items supplied with your product may vary depending on the model.

· Image shown may differ from your TV.

India region only. (Below sentence is not applicable for above 1920 x 1080 resolution TV models.) ATTENTION: This product is qualified for the BEE Star rating in the `Home’ Mode. The Objectives of Star Labeling Program is designed to promote energy efficient products and practices. When the television is initially set up, it is designed to meet the BEE Star Labeling requirements while maintaining optimum picture quality. · Changes to certain functionalities of this television (TV Guide, Picture/sound etc) may change the power consumption. · Depending upon such changed setting (eg., Retail mode), the power consumption may vary which possibly could exceed the stated energy consumption. To reset the television to Star rating qualified settings, select`Home’mode from the initial set-up procedure in`factory settings’under the `Set-up’ menu.3

Warning! Safety instructionsCAUTION RISK OF ELECTRIC SHOCKDO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.This symbol is intended to alert the user to the presence of uninsulated”dangerous voltage”within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING : TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

· TO PREVENT THE SPREAD OF FIRE, KEEP CANDLES OR OTHER ITEMS WITH OPEN FLAMES AWAY FROM THIS PRODUCT AT ALL TIMES.· Do not place the TV and/or remote control in the following environments: – Keep the product away from direct sunlight. – An area with high humidity such as a bathroom. – Near any heat source such as stoves and other devices that produce heat. – Near kitchen counters or humidifiers where they can easily be exposed to steam or oil. – An area exposed to rain or wind. – Do not expose to dripping or splashing and do not place objects filled with liquids, such as vases, cups, etc. on or over the apparatus (e.g., on shelves above the unit). – Near flammable objects such as gasoline or candles, or expose the TV to direct air conditioning. – Do not install in excessively dusty places.Otherwise, this may result in fire, electric shock, combustion/ explosion, malfunction or product deformation.

· Ventilation – Install your TV where there is proper ventilation. Do not install in a confined space such as a bookcase. – Do not install the product on a carpet or cushion. – Do not block or cover the product with cloth or other materials while unit is plugged in.· Take care not to touch the ventilation openings. When watching the TV for a long period, the ventilation openingsmay become hot. · Protect the power cord from physical or mechanical abuse,such as being twisted, kinked, pinched, closed in a door, orwalked upon. Pay particular attention to plugs, wall outlets,and the point where the cord exits the device. · Do not move the TV whilst the Power cord is plugged in. · Do not use a damaged or loosely fitting power cord. · Be sure to grasp the plug when unplugging the power cord.Do not pull on the power cord to unplug the TV. · Do not connect too many devices to the same AC poweroutlet as this could result in fire or electric shock.

· Disconnecting the Device from the Main Power – The power plug is the disconnecting device. In case of an emergency, the power plug must remain readily accessible.· Do not let your children climb or cling onto the TV. Otherwise, the TV may fall over, which may cause serious injury.· Outdoor Antenna Grounding (Can differ by country): – If an outdoor antenna is installed, follow the precautions below.An outdoor antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can come in contact with such power lines or circuits as death or serious injury can occur. · Grounding (Except for devices which are not grounded.) – TV with a three-prong grounded AC plug must be connected to a three-prong grounded AC outlet. Ensure that you connect the earth ground wire to prevent possible electric shock. · Never touch this apparatus or antenna during a lightning storm. You may be electrocuted. · Make sure the power cord is connected securely to the TV and wall socket if not secured damage to the Plug and socket may occur and in extreme cases a fire may break out. · Do not insert metallic or inflammable objects into the product. If a foreign object is dropped into the product, unplug the power cord and contact the customer service. · Do not touch the end of the power cord while it is plugged in. You may be electrocuted.

· If any of the following occur, unplug the product immediately and contact your local customer service. – The product has been damaged. – If water or another substance enters the product (like an AC adapter, power cord, or TV). – If you smell smoke or other odors coming from the TV. – When lightning storms or when unused for long periods of time.Even the TV is turned off by remote control or button, AC power source is connected to the unit if not unplugged in. · Do not use high voltage electrical equipment near the TV (e.g., a bug zapper). This may result in product malfunction. · Do not attempt to modify this product in any way without written authorization from LG Electronics. Accidental fire or electric shock can occur. Contact your local customer service for service or repair. Unauthorized modification could void the user’s authority to operate this product. · Use only an authorized attachments / accessories approved by LG Electronics. Otherwise, this may result in fire, electric shock, malfunction, or product damage. · Never disassemble the AC adapter or power cord. This may result in fire or electric shock. · Handle the adapter carefully to avoid dropping or striking it. An impact could damage the adapter. · To reduce the risk of fire or electrical shock, do not touch the TV with wet hands. If the power cord prongs are wet or covered with dust, dry the power plug completely or wipe dust off.

· Batteries – Store the accessories (battery, etc.) in a safe location out of the reach of children. – Do not short circuit, disassemble, or allow the batteries to overheat. Do not dispose of batteries in a fire. Batteries should not be exposed to excessive heat. – Caution: Risk of fire or explosion if the battery is replaced by an incorrect type.· Moving – When moving, make sure the product is turned off, unplugged, and all cables have been removed. It may take 2 or more people to carry larger TVs. Do not press or put stress on the front panel of the TV. Otherwise, this may result in product damage, fire hazard or injury.· Keep the packing anti-moisture material or vinyl packing out of the reach of children.· Do not allow an impact shock, any objects to fall into the product, and do not drop anything onto the screen.· Do not press strongly upon the panel with a hand or a sharp object such as a nail, pencil, or pen, or make a scratch on it. It may cause damage to screen.· Cleaning – When cleaning, unplug the power cord and wipe gently with a soft/dry cloth. Do not spray water or other liquids directly on the TV. Do not clean your TV with chemicals including glass cleaner, any type of air freshener, insecticide, lubricants, wax (car, industrial), abrasive, thinner, benzene, alcohol etc., which can damage the product and/or its panel. Otherwise, this may result in electric shock or product damage.6

PreparingLifting and moving the TVPlease Note the following advice to prevent the TV from being scratched or damaged and for safe transportation regardless of its type and size. · It is recommended to move the TV in the box or packing material that the TV originally came in. · Before moving or lifting the TV, disconnect the power cord and all cables. · When holding the TV, the screen should face away from you to avoid damage.· Hold the top and bottom of the TV frame firmly. Make sure not to hold the transparent part, speaker, or speaker grill area.· When transporting a large TV, there should be at least 2 people. · When transporting the TV by hand, hold the TV as shown in the following illustration. · When transporting the TV, do not expose the TV to jolts or excessive vibration. · When transporting the TV, keep the TV upright, never turn the TV on its side or tilt towards the left or right. · Do not apply excessive pressure to cause flexing / bending of frame chassis as it may damage screen. · When handling the TV, be careful not to damage the protruding buttons.· Avoid touching the screen at all times, as this may result in damage to the screen. · When attaching the stand to the TV set, place the screen facing down on a cushioned table or flat surface to protect the screen fromscratches.7

Mounting on the Table1 Lift and tilt the TV into its upright position on a table. · Leave a 10 cm (minimum) space from the wall for proper ventilation.2 Connect the power cord to a wall outlet.

10 cm 10 cm10 cm

(Depending on model)· Do not apply foreign substances (oils, lubricants, etc.) to the screw parts when assembling the product. (Doing so may damage the product.)· If you install the TV on a stand, you need to take actions to prevent the product from overturning. Otherwise, the product may fall over, which may cause injury.· Do not use any unapproved items to ensure the safety and product life span. · Any damage or injuries caused by using unapproved items are not covered by the manufacturer’s warranty. · Make sure that the screws are inserted correctly and fastened securely. (If they are not fastened securely enough, the TV may tiltforward after being installed.) Do not use too much force and over tighten the screws; otherwise screw may be damaged and not tighten correctly.· If a television is not positioned in a sufficiently stable location, it can be potentially hazardous due to falling. Many injuries, particularly to children, can be avoided by taking simple precautions such as: – Using cabinets or stands recommended by the manufacturer of the television. – Only using furniture that can safely support the television. – Ensuring the television is not overhanging the edge of the supporting furniture. – Not placing the television on tall furniture (for example, cupboards or bookcases) without anchoring both the furniture and the television to a suitable support. – Not standing the televisions on cloth or other materials placed between the television and supporting furniture. – Educating children about the dangers of climbing on furniture to reach the television or its controls.

Securing TV to the Wall

1 Insert and tighten the eye-bolts, or TV brackets and bolts on the back of the TV. · If there are bolts inserted at the eye-bolts position, remove the bolts first.2 Mount the wall brackets with the bolts to the wall. Match the location of the wall bracket and the eye-bolts on the rear of the TV.3 Connect the eye-bolts and wall brackets tightly with a sturdy rope. Make sure to keep the rope horizontal with the flat surface.· Use a platform or cabinet that is strong and large enough to support the TV securely. · Brackets, bolts and ropes are not provided. You can obtain additional accessories from your localdealer.

(Depending on model)

Mounting to the WallAttach an optional wall mount bracket at the rear of the TV carefully and install the wall mount bracket on a solid wall perpendicular to the floor. When you attach the TV to other building materials, please contact qualified personnel. LG recommends that wall mounting be performed by a qualified professional installer. We recommend the use of LG’s wall mount bracket. LG’s wall mount bracket is easy to move with cables connected. When you do not use LG’s wall mount bracket, please use a wall mount bracket where the device is adequately secured to the wall with enough space to allow connectivity to external devices. It is advised to connect all the cables before installing fixed wall mounts.

10 cm 10 cm10 cm 10 cm(Depending on model)

· Remove the stand before installing the TV on a wall mount by performing the stand attachment in reverse. · For more information of screws and wall mount bracket, refer to the Separate Purchase. · If you intend to mount the product to a wall, attach VESA standard mounting interface (optional parts) to the back of the product.When you install the set to use the wall mounting bracket (optional parts), fix it carefully so as not to drop.· When mounting a TV on the wall, make sure not to install the TV by hanging the power and signal cables on the back of the TV. · Do not install this product on a wall if it could be exposed to oil or oil mist. This may damage the product and cause it to fall. · Do not use a sharp object when you detached the cable cover. This could damage the cable or the cabinet. It may also cause personalharm. (Depending on model)

(Only 75/86NANO86*, 75/86NANO91*)

(Only 50/55/65NANO86*, 55/65NANO91*)

(Depending on model)

· When installing the wall mounting bracket, it is recommended to cover the stand hole using tape, in order to prevent the influx of dust and insects. (Depending on model)

Stand hole

(Depending on model)

Wall Mounting Bracket

(Depending on model) Make sure to use screws and wall mount bracket that meet the VESA standard. Standard dimensions for the wall mount kits are described in the following table.

Model

43/50NANO75* 43/50NANO77* 50NANO80* 50NANO85* 50NANO86*

65NANO73* 55/65NANO75* 55/65NANO77* 55/65NANO80* 55/65NANO83* 55/65NANO86* 55NANO90* 55NANO91*

65NANO90* 65NANO91*

Screws distance (A) (mm)

200

300

400

Standard screwNumber of screws Wall mount bracket

M6 2 WB21LMB

Model

75NANO80* 75NANO85* 75NANO86* 75NANO90* 75NANO91*

Screws distance (A x B) (mm)Standard screwNumber of screws Wall mount bracket

1,281 x 125 M8 4 WB21LGB

86NANO85* 86NANO86* 86NANO90* 86NANO91*1,586 x 125 M8 4 WB21LGB

A B

ModelVESA (A x B) (mm) Standard screw Number of screws Wall mount bracket

43/50NANO75* 43/50NANO77* 50NANO80* 50NANO85* 50NANO86*200 x 200 M6 4 LSW240B MSW240

55NANO75* 55NANO77* 55NANO80* 55NANO83* 55NANO86* 55NANO90* 55NANO91* 300 x 300 M6 4 OLW480B MSW240

65NANO73* 65NANO75* 65NANO77* 65NANO80* 65NANO83* 65NANO86*300 x 300 M6 4OLW480B

75NANO73* 75NANO75* 75NANO80* 75NANO85* 75NANO86* 65/75NANO90* 65/75NANO91* 400 x 400 M6 4LSW440B

86NANO73* 86NANO75* 86NANO85* 86NANO86* 86NANO90* 86NANO91*600 x 400 M8 4LSW640B

Antenna/CableConnect the TV to a wall antenna socket with an RF cable (75 ). · Use a signal splitter to use more than 2 TVs. · If the image quality is poor, install a signal amplifier properly to improve the image quality. · If the image quality is poor with an antenna connected, try to realign the antenna in the correct direction. · An antenna cable and converter are not supplied. · For a location that is not supported with Ultra HD broadcasting, this TV cannot receive Ultra HD broadcasts directly.Satellite dishConnect the TV to a satellite dish to a satellite socket with a satellite RF cable (75 ). (Depending on model)12

Starting TVTurning on the TVYou can simply operate the TV functions, using the button.

Using button

Power On (Press) Power Off1) (Press and Hold) Menu Control (Press2)) Menu Selection (Press and Hold3))

1) All running apps will close, and any recording in progress will stop. (Depending on country)2) You can access and adjust the menu by pressing the button when TV is on. 3) You can use the function when you access menu control.

Note

· If the TV is turned on for the first time after it was shipped from the factory, initialization of the TV may take a few

minutes.

Adjusting the menu

When the TV is turned on, press the button one time. You can adjust the Menu items using the button.

Turns the power off. Adjusts the volume level.

Changes the input source. Scrolls through the saved programmes.

Note

· Your TV’s OSD (On Screen Display) may differ slightly from that shown in this manual.

· The available menus and options may differ from the input source or product model that you are using.

· New features may be added to this TV in the future.

· The device must be easily accessed to a location outlet near the access. Some devices are not made by turning on / off button, turning off the device and unplugging the power cord.

Inserting the batteryWhen the message [Magic Remote battery is low. Please change the battery.] is displayed, replace the battery. To replace batteries, open the battery cover, replace batteries (1.5 V AA) matching the and ends to the label inside the compartment, and close the battery cover.· Do not mix new batteries with old batteries. This may cause the batteries to overheat and leak. · Failure to match the correct polarities of the battery may cause the battery to burst or leak, resulting in fire, personal injury, or ambientpollution. · This apparatus uses batteries. In your community there might be regulations that require you to dispose of these batteries properly dueto environmental considerations. Please contact your local authorities for disposal or recycling information. · Batteries inside or inside the product shall not be exposed to excessive heat such as sunshine, fire or the like.Registering Magic Remote ControlHow to register the Magic Remote ControlTo use the Magic Remote, first pair it with your TV. 1 Put batteries into the Magic Remote and turn the TV on. 2 Point the Magic Remote at your TV and press the Wheel (OK) on the remote control. * If the TV fails to register the Magic Remote, try again after turning the TV off and back on.How to deregister the Magic Remote ControlPress the (BACK) and (HOME) buttons at the same time, for five seconds, to unpair the Magic Remote with your TV. * Press and hold the (HOME) and (Q. Settings) buttons for more than 5 seconds to disconnect and re-register the Magic Remote at thesame time. · It is recommended that an Access Point (AP) be located more than 0.2 m away from the TV. If the AP is installed closer than 0.2 m, the Magic remote control may not perform as expected due to frequency interference.14

Using Remote Control

Using Magic Remote Control(Depending on model) The descriptions in this manual are based on the buttons on the remote control. Please read this manual carefully and use the TV correctly.

Power Turns the TV on or off.

(DASH) Inserts a between

numbers such as 2-1 and 2-2.

Microphone

Accesses the saved programmes

list.

Accesses the [Guide].

Accesses the [Edit Quick Access].

– [Edit Quick Access] is a feature that

allows you to enter a specified app

or Live TV directly by pressing and

holding the number buttons.

Volume buttons Adjusts the volume level.

Programme buttons Scrolls through the saved programmes.

Home Accesses the Home menu.

Home Launches the last used apps.

Input Changes the input source.

Input Accesses the [Home Dashboard].Wheel (OK) Press the centre of button to select a menu. You can change channels by using button.

33 33 33

Wheel (OK) Accesses the [Magic

Explorer]. You can run the [Magic

Explorer] feature when the pointer

colour is changed to purple. If

watching a programme, press and

hold down the pointer onto the video.

When using [TV Guide], [Settings],

[Sports Alert], or [Art Gallery], press

and hold down on the text.

Back Returns to the previous level.

Number buttons Enters numbers. Accesses the [Quick Help]. More actions Displays more remote control functions. Audio descriptions function will be enabled. Mute Mutes all sounds.Mute Accesses the [Accessibility] menu. Voice recognition Network connection is required to use the voice recognition function. Check for recommended content. (Some recommended services may not be available in some countries.) Voice recognition Speak while pressing and holding the button to use the voice recognition feature. Up/Down/Left/Right Press the up, down, left or right button to scroll the menu. If you press buttons while the pointer is in use, the pointer will disappear from the screen and Magic Remote will operate like a general remote control. To display the pointer on the screen again, shake Magic Remote to the left and right. Q. Settings Accesses the Quick Settings.Q. Settings Displays the [All Settings] menu.These access special functions in some menus.Red button Runs the record function. Streaming Service buttons Connects to the Video Streaming Service. Home Dashboard Accesses the [Home Dashboard].

Back Clears on-screen displays and returns to last input viewing.

User Guide Accesses the [User Guide].

Accesses your favorite programmes list.

3 ,

Control buttons Controls media contents.

(Some buttons and services may not be provided depending on models or regions.)

Note

To use the button, press and hold for more than 1 second.

· In Analogue TV and some countries, some remote control buttons may not work.

ConnectionsConnect various external devices to the TV and switch input modes to select an external device. For more information of external device’s connection, refer to the manual provided with each device.

HDMI

· When connecting the HDMI cable, the product and external devices should be turned off and unplugged.

NoteUSB

· Supported HDMI Audio format (Depending on model): True HD (48 kHz),Dolby Digital / Dolby Digital Plus (32 kHz / 44.1 kHz / 48 kHz),PCM (32 kHz / 44.1 kHz / 48 kHz / 96 kHz / 192 kHz)· If the device connected to Input Port also supports HDMI Deep Colour, your picture may be clearer. However, if the device doesn’t support it, it may not work properly. In that case, change the TV’s [HDMI Deep Colour] setting to off.· [General] [Devices] [HDMI Settings] [HDMI Deep Colour] (Only 86NANO73*, 86NANO75*, NANO85*, NANO86*, NANO90*, NANO91*) – On : Support 4K @ 50/60 Hz (4:4:4, 4:2:2, 4:2:0),<3,4 port Only> 4K @ 100/120 Hz (4:4:4, 4:2:2, 4:2:0) – Off : Support 4K @ 50/60 Hz (4:2:0)(Except for 86NANO73*, 86NANO75*, NANO85*, NANO86*, NANO90*, NANO91*) – On : Support 4K @ 50/60 Hz (4:4:4, 4:2:2, 4:2:0) – Off : Support 4K @ 50/60 Hz (4:2:0) · Use a certified cable with the HDMI logo attached. · If you do not use a certified HDMI cable, the screen may not display or a connection error may occur. · Recommended HDMI Cable Types – Ultra High Speed HDMI®/TM cable (3 m or less)Some USB Hubs may not work. If a USB device connected using a USB Hub is not detected, connect it to the USB port on the TV directly.

Note

· For an optimal connection, HDMI cables and USB devices should have bezels less than 10 mm thick and

18 mm width. Use an extension cable that supports

if the USB cable or USB memory stick does not fit

into your TV’s USB port. (Depending on model)

* A 10 mm

* B 18 mm

CI module View the encrypted (pay) services in digital TV mode. (Depending on model)

NoteExternal DevicesNote

· Check if the CI module is inserted into the

in the right direction. If the module is not

inserted properly, this can cause damage to the TV and the

· If the TV does not display any video and audio when CI+ CAM is connected, please contact to the

Terrestrial/Cable/Satellite Service Operator.

Available external devices are: Blu-ray player, HD receivers, DVD players, VCRs, audio systems, USB storage devices, PC, gaming devices, and other external devices.

· The external device connection may differ from the model. · Connect external devices to the TV regardless of the order of the TV port. · If you record a TV program on a Blu-ray/DVD recorder or VCR, make sure to connect the TV signal inputcable to the TV through a DVD recorder or VCR. For more information of recording, refer to the manualprovided with the connected device. · Refer to the external equipment’s manual for operating instructions. · If you connect a gaming device to the TV, use the cable supplied with the gaming device. · In PC mode, there may be noise associated with the resolution, vertical pattern, contrast or brightness. Ifnoise is present, change the PC output to another resolution, change the refresh rate to another rate oradjust the brightness and contrast on the [Picture] menu until the picture is clear. · In PC mode, some resolution settings may not work properly depending on the graphics card. · If ULTRA HD content is played on your PC, video or audio may become disrupted intermittently dependingon your PC’s performance. (Depending on model) · When connecting via a wired LAN, it is recommended to use a CAT 7 cable. (Only when port isprovided.)

Troubleshooting

Cannot control the TV with the remote control. No image display and no sound is produced. The TV turns off suddenly. When connecting to the PC (HDMI), no signal is detected. Abnormal DisplayGenerated Sound

· Check the remote control sensor on the product and try again. · Check if there is any obstacle between the product and the remote control. · Check if the batteries are still working and properly installed ( to , to ).· Check if the product is turned on. · Check if the power cord is connected to a wall outlet. · Check if there is a problem in the wall outlet by connecting other products.· Check the power control settings. The power supply may be interrupted. · Check if the auto-off function is activated on the settings related time. · If there is no signal while the TV is on, the TV will turn off automatically after 15 minutes of inactivity.· Turn the TV off/on using the remote control. · Reconnect the HDMI cable. · Restart the PC with the TV on.· If the product feels cold to the touch, there may be a small”flicker”when it is turned on. This is normal, there is nothing wrong with product.· This panel is an advanced product that contains millions of pixels. You may see tiny black dots and/ or brightly coloured dots (red, blue or green) at a size of 1 ppm on the panel. This does not indicate a malfunction and does not affect the performance and reliability of the product. This phenomenon also occurs in third-party products and is not subject to exchange or refund.· You may find different brightness and colour of the panel depending on your viewing position(left/right/ top/down).This phenomenon occurs due to the characteristic of the panel.It is not related with the product performance, and it is not malfunction. · Displaying a still image for a prolonged period of time may cause image sticking. Avoid displaying a fixedimage on the TV screen for a long period of time.· “Cracking” noise: A cracking noise that occurs when watching or turning off the TV is generated by plastic thermal contraction due to temperature and humidity. This noise is common for products where thermal deformation is required.· Electrical circuit humming/panel buzzing: A low level noise is generated from a high-speed switching circuit, which supplies a large amount of current to operate a product. It varies depending on the product. This generated sound does not affect the performance and reliability of the product.

· When cleaning the product, be careful not to allow any liquid or foreign objects to enter the gap between the upper, left or right side of the panel and the guide panel. (Depending on model)

· Make sure to wring any excess water or cleaner from the cloth. · Do not spray water or cleaner directly onto the TV screen. · Make sure to spray just enough of water or cleaner onto a dry cloth to wipe the screen.

Specifications

(Depending on country)

Television systemProgramme coverage Maximum number of storableprogrammes External antenna impedanceCI Module3) (W x H x D)

Broadcasting Specifications

Digital TV

Analogue TV

DVB-T/T21) DVB-T/T2/C/S/S22)

PAL B/B, PAL B/G, PAL D/K, PAL-I SECAM B/G, SECAM D/K NTSC-M

VHF, UHF C-Band2), Ku-Band2)

VHF, UHF, CATV

DVB-T/T2 & Analogue TV : 3000 DVB-S/S2 : 6000

100.0 mm x 55.0 mm x 5.0 mm

1) Only DVB-T2 support models. (Despite DVB-T2 model, DVB-T/T2 function does not apply in Philippines.) 2) Only DVB-T2/C/S2 support models. 3) Depending on model.

(Only 86NANO73*, 86NANO75*, NANO85*, NANO86*, NANO90*, NANO91*)

Wireless module (LGSBWAC95) Specifications

Wireless LAN (IEEE 802.11a/b/g/n/ac)

Frequency range

Output Power (Max.)

2,400 to 2,483.5 MHz

19 dBm

5,150 to 5,725 MHz

18 dBm

5,725 to 5,850 MHz

13.5 dBm

Bluetooth

Frequency range

Output Power (Max.)

2,400 to 2,483.5 MHz

9 dBm

As band channels can vary per country, the user cannot change or adjust the operating frequency. This product is configured for the regional frequency table. For consideration of the user, this device should be installed and operated with a minimum distance of 20 cm between the device and the body.

(Except for 86NANO73*, 86NANO75*, NANO85*, NANO86*, NANO90*, NANO91*)

Wireless module(LGSBWAC03)Specifications

Wireless LAN (IEEE 802.11a/b/g/n/ac)

Frequency range

Output Power (Max.)

2,400 to 2,483.5 MHz

18.5 dBm

5,150 to 5,725 MHz

19.5 dBm

5,725 to 5,850 MHz

11.5 dBm

Bluetooth

Frequency range

Output Power (Max.)

2,400 to 2,483.5 MHz

9 dBm

(Australia and New Zealand region only)

The use of the 5,150 5,350 MHz band is restricted to indoor use only. This restriction exists in the countries Australia (AU) and New Zealand (NZ). (For Wi-Fi/Bluetooth built-in model or Wi-Fi built-in model) “RF Radiation Exposure Statement This equipment shall be installed and used at a minimum distance of 20 cm from the human body.”

Operating Temperature Operating Humidity Storage Temperature Storage Humidity

Environment condition

0 °C to 40 °C Less than 80 % -20 °C to 60 °C Less than 85 %

· The energy information provided with the product is indicated in accordance with the regulations of each country. (Depending on Country) – The Energy consumption is measured in accordance with IEC 62087.· Actual Energy consumption may vary depending on factors such as the type of video content being played and TV settings. · For information of the power supply and power consumption, refer to the label attached to the product. (Depending on Country)– The typical power consumption is measured in accordance with IEC 62087 or each country’s energy regulations.* On some models, the label is inside the external device connection terminal cover.* Depending on the model or country, the typical power consumption may not be on label.

Open Source Software Notice InformationTo obtain the source code under GPL, LGPL, MPL, and other open source licenses, that is contained in this product, please visit http://opensource.lge. com. In addition to the source code, all referred license terms, warranty disclaimers and copyright notices are available for download. LG Electronics will also provide open source code to you on CD-ROM for a charge covering the cost of performing such distribution (such as the cost of media, shipping, and handling) upon email request to This offer is valid for a period of three years after our last shipment of this product. This offer is valid to anyone in receipt of this information.Licenses(Magic Remote supported models only)(Australia region only)Freeview Plus provides access to content and services from the Freeview networks. The Freeview Plus service provides a 7 + day EPG, all available Catch Up TV, recommendations and the ability to set reminders and favourites. Freeview Plus is available by pressing the green button on the remote. *Freeview Plus uses HbbTV technology which combines broadcast and broadband. It requires an internet connection. Normal data usage charges and conditions apply.21

Regulatory

WARNING! (STABILITY HAZARD)A television set may fall, causing serious personal injury or death. Many injuries, particularly to children, can be avoided by taking simple precautions such as:– ALWAYS use cabinets or stands or mounting methods recommended by the manufacturer of the television set. – ALWAYS use furniture that can safely support the television set. – ALWAYS ensure the television set is not overhanging the edge of the supporting furniture. – ALWAYS educate children about the dangers of climbing on furniture to reach the television set or its controls. – ALWAYS route cords and cables connected to your television so they cannot be tripped over, pulled or grabbed. – NEVER place a television set in an unstable location. – NEVER place the television set on tall furniture (for example, cupboards or bookcases) without anchoring both the furniture and the televisionset to a suitable support. – NEVER place the television set on cloth or other materials that may be located between the television set and supporting furniture. – NEVER place items that might tempt children to climb, such as toys and remote controls, on the top of the television or furniture on which thetelevision is placed. If the existing television set is going to be retained and relocated, the same considerations as above should be applied.Symbols

Refers to alternating current (AC). Refers to direct current (DC). Refers to class II equipment.

Refers to stand-by. Refer to “ON” (power). Refers to dangerous voltage.

Environmental Information(Only India)Disposal of your old appliance (as per e-waste Rules)1. When this crossed out wheeled bin symbol is depicted on the product and its operator’s manual, it means the product is covered by the e-waste Management and Handling Rules, 2011 and are meant to be recycled, dismantled, refurbished or disposed off.2. Do’s: a. The product is required to be handed over only to the authorized recycler for disposal. b. Keep the product in isolated area, after it becomes non-functional/unrepairable so as to prevent its accidental breakage.Don’t: a. The product should not be opened by the user himself/herself, but only by authorized service personnel. b. The product is not meant for re-sale to any unauthorized agencies/scrap dealer/kabariwalah. c. The product is not meant for mixing into household waste stream. d. Do not keep any replaced spare part(s) from the product in exposed area. 3. Any disposal through unauthorized agencies/person will attract action under Environment (Protection) Act 1986. 4. “This product is complied with the requirement of Hazardous Substances as specified under Rule 13 (1) & (2) of the E-Waste (Management & Handling) Rules, 2011.” 5. To locate a nearest collection centre or call for pick-up (limited area only) for disposal of this appliance, please contact Toll Free No. 1800-3159999 / 1800-180-9999 for details. All collection centre and pick up facilities are done by third parties with LG Electronics India Pvt. Ltd. Merely as a facilitator. For more detailed information, please visit: http://www.lg.com/in.

( –

)

The model and serial number of the product are located on the back and on one side of the product. Record them below in case you ever need service.ModelSerial No.

References

[xyz-ips snippet=”download-snippet”]

Posted

2023-01-22

admin

Tags:

_pdf, led tv, LG