PYLE RV Wall Mount Audio/Video Receiver PLRVST400 User Manual
Table of Contents
PLRVST400RV Wall Mount Audio/ Video ReceiverAV Stereo Headunit with Wireless Bluetooth Streaming,Multimedia Disc Player, HDMI ARC, AUX/MP3/USB Reader
INSTALLATION
Notes:Choose the mounting location where the unit will not interfere with the normal driving function of the driver.
Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up properly and the unit and the system work properly.
Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunctions.
Consult with your nearest dealer if installation requires the drilling of holes or other modifications of the vehicle.
Install the unit where it does not get in the driver’s way and cannot injure the passenger if there is an emergency stop.
If installation angel exceeds 30°from horizontal, the unit might not give its optimum performance.
Avoid installing the unit where it would be subject to high temperature, such as from direct sunlight, or from hot air, from the heater, or where it would be subject to dust, dirt or excessive vibration.
DIN FRONT/REAR-MOUNT
This unit can be properly installed either from “Front” (conventional DIN Front-mount) or “Rear” (DIN Rear-mount installation, utilizing threaded screw holes at the sides of the unit chassis). For details, refer to the following illustrated installation methods.
Installation OpeningThis unit can be installed in any dashboard having an opening as shown below:
ATTENTIONS OF INSTALLATION
This player should be installed by professional technician.
please read the instruction and operation of equipment carefully before installing.
Make sure to connect other wires before power connection.
To avoid short circuit. Please make sure all the exposed wire are insulating.
Please fix all the wires after installation.
Please make connection to the player accordingly to this instruction manual. Wrong connection may cause damage.
This player only fit for 12V DC device and please make sure your car belongs to this kind of cathode grounding electrical system.
Please connect the wires rightly. Wrong connection will cause malfunction or damage the electrical system.
MOUNTING
CAUTION: Do not install radio without rear cover installed. No user-serviceable parts inside. Rear cover provides protection against potential fire hazard.
13. 6 DIR+14. BAND15. MODE16. POWER/MUTE17. /DISP18. 19. 20. (Eject)21. EAR PHONE OUTPUT22. AUX IN Jack23. USB INTERFACE24. RESET button
OPERATION
Turn ON/OFF the unit and mute functionPress /MUTE button to turn ON the unit. When the unit is on, shortly press this button for mute on/off. Press and hold this button to turn off the unit.Audio & Setting AdjustmentShortly press SEL button and rotate VOL knob to show below: ZONE A->ZONE B->ZONE C. To select one of them and press SEL and rotate VOL to enter below items: BAS (-7~+7)->TRE (-7~+7)->BAL (R7~L7)->EQ (POP-ROCK-CLASS-JAZZ-OFF) ->LOUD (off/on)->P-VOL (00-40) In each item, press SEL and rotating the VOL knob to set them.Press and hold SEL button and rotate VOL into the SETTING menu as below: CT (indep/sync)->CLOCK (12/24)->BEEP (off/on)->AREA (USA/EUR)->DX (LOC) ->STEREO (MONO) In each item, press SEL and rotating the VOL knob to set them. When shows menu, press the DISP button to exit the menu.P_VOL SettingSetting the power on volume. If the volume at shutdown is small than the P-VOL. Next time turning on the unit, the volume will be maintained at shutdown volume. If the volume at shutdown is greater than the P-VOL. Next time turning on the unit the volume will be restored to the P-VOL value.CT (INDEP/SYNC)CT INDEP: The clock works independently. It doesn’t be synchronized to the RDS station’s time.CT SYNC: The clock will be synchronized to the received RDS station’s time.Note: When the time was set by manual. The CT will go back to INDEP mode automatically. CLOCK 24/12: Setting the time to 24H or 12H format. BEEP (ON/OFF): Turn on/off the beep sound.AREA (USA/EUR): To choose USA or EUROPE frequency.DX/LOC (Distance/Local): LOC: Receive the strong signal station only in seek station.DX: Receive strong and weak signal station in seek the station.STEREO/MONO:STEREO: Receive FM stereo signal.MONO: Change FM stereo to monochrome. It can reduce the noise when the signal is weak.Dimmer FunctionPress DIM button to set the brightness to high/low.
ALARM OperationPress and hold ALARM button to set the alarm time (using VOL knob to set them). Shortly press ALARM button to on/off alarm function. When alarm function is ON. The time is running to the alarm time. The speaker will output beep sound. The beep sound will output all the time until any key was pressed.
SLEEP OperationPress and hold SLEEP button to set the sleep time (using VOL knob to set them). Shortly press SLEEP button to on/off sleep function. When sleep function is on and the time is running to the set time. The unit will turn off the unit automatically.
Information/Clock displayShortly press DISP button to show the clock or information.
Clock SettingPress and hold DISP button for 2 seconds. The “HH” will be flashing. Rotate VOL knob to set the hour. After that press DISP or SEL button the “MM” will be flashing. Rotate VOL knob to set the minute. Then press DISP or SEL button to confirm.
Speakers Output ControlThe three speaker output buttons (SPEAKER A/B/C) control speaker output. Press any of the three buttons to turn up or down the corresponding speaker output.
RCA/HDMIOutput Behind the head unit, there are RCA sockets output. According the wiring picture above to connect. When playing the video file. You also use the HDMI port connect to the TV set (TV set needs to be set to HDMI source).
AUX IN/AV IN FunctionAUX IN for front panel 3.5mm jack. AV IN for RCAs (Audio + Video) behind of the unit.Press MODE button switch to AUX IN/AV IN source.
ARC FunctionConnecting the head unit and TV set used a HDMI cable. Press MODE button switch to HDMI ARC mode. The TV set’s sound will transmit to the head unit’s speakers.
MCU ResetWhen some errors occur in display or functions doesn’t work. Press RESET button (24) to reset the MCU. Then press POWER button to turn ON the unit.
DATA ResetPress MODE button switch to AUX IN source. Press and hold “” button for 5 seconds. It will restore all data to factory settings. (Note: All memories will be lost.)
RADIO OPERATIONReceiving a radio station Press MODE button to select radio source. Then press BAND button to select a band. Shortly press button to receive the desired radio station. Press and hold button for manual tuning the frequency.
Auto Store StationPress and hold BAND button for 2 seconds to auto store stations to numeric buttons 1-6 of band 1~3.
Manually store station & recall preset stationTo receive a station with or button. Press and hold one of the 1- 6 preset button for 2 seconds. The current station is stored into the number button. Shortly press the preset button (1~6) to directly listen the station that saved in the corresponding preset button.
In WEATHER BAND1 button: 162.400 MHz2 button: 162.425 MHz3 button: 162.450 MHz4 button: 162.475 MHz5 button: 162.500 MHz6 button: 162.525 MHzThe next station is 162.550 MHz. Press button to change these stations.
DISC/MP3/WMA OperationSwitch to DISC SourceGently insert the DISC with the printed side uppermost into disc slot. DISC playback begins. Or press MODE button switch to DISC source.
SELECTING TRACKSPress button move to the previous / next track.Hold button to fast reverse or fast forward. Press “” button to play again.
Pause/Play OperationPress button to pause playing. Press it again to resume play.
Intro OperationPress INT button to play first 10 seconds of each track. Press it again to cancel this function.
Repeat One/All OperationPress RPT button to repeat the same track. Press it again to repeat all tracks.
Random ON/OFF OperationPress RDM button to play all tracks in random order. Press again to cancel this function.
Eject the disc: Press button to eject the disc.
DIR+/DIR- Function (for MP3/WMA)Press DIR-/DIR+ button to select previous/next directory to play.
+10/-10 File Function (for MP3/WMA)Press and hold DIR+/DIR- button for 2 seconds to skip +10/-10 file to play.
Search Song OperationPress BAND button to select song search mode: DIR SCH or NUM SCH
DIR SCH: Press BAND button one time. It shows “DIR SCH”. Rotating VOL knob to select the folder then press SEL knob into the folder. Rotate the VOL knob again to select the song. Then press SEL to play.
NUM SCH: Press BAND button twice. It shows “NUM SCH”. You can select the song by directly enter numeric buttons: 0~9 (MODE=7, =8, =9, DISP=0). You also can rotate the VOL knob to select the numeric. Then press SEL to play.
Video/Photo/Music Playing ChangeWhen there are Video/Photo/Music files in the disc/USB. Insert the disc/USB to the unit, it will play the music automatically. Repeatedly Press and hold BAND button to change to below playing: Music–>Video–>Photo
CAUTION:
When connecting an MP3 player that has normal battery (non rechargeable battery), you should remove the battery first from the MP3 player then connect it to the USB interface. Otherwise, it may cause battery burst.
When there are important files in the DISC/USB/SD, do not connect it to the main unit to play. Our company assumes no responsibility for any important files that loss or damaged.
SUPPORTED MP3/WMA DECODING MODESThe main unit supports MP3/WMA (Windows Media Audio) decoding modes as below.
Standard
Bit Rate (kbps)
Bit Rate (kbps)
MPEG1 Audio Layer 3 (44.1 kHz)
32, 48, 64, 96, 128192256320
32, 48, 64, 96, 128, 192, 256, 320
Windows Media Audio (44.1 kHz)
64,96,128,192
64,96,128,192
The USB solution can support:
Folder: 500 max.
File: 999 max.
Depth of folder: 8 layers
Size: 64 GB
WIRELESS BT STREAMING OPERATIONPAIRINGSelect the Wireless BT item and search the BT device on your phone. Select “PyleUSA” and input password “0000” if it needs a password. The BT icon will be displayed when successful paired.
Wireless BT Audio (A2DP function)Press MODE button switch to “BT MUSIC” source. It will play a song of your mobile phone automatically. Press key to pause/play the song. Press button to select next/ previous song.
Disconnect the Wireless BTAfter the phone is paired with the unit. Hold MODE key to disconnect/re-connect BT. Note: At the first time pair with mobile phone, you have to use mobile phone to pair the unit. BT OFF/ON item only to disconnect and reconnect function.
DISC NOTESA. Notes on discs:Attempting to use non-standard shape discs (e.g. square, start, heart) may
Damage the unit. Be sure to use round shape CD discs only for this unit.
Do not stick paper or tape, etc, into the label side or the recording side of any discs, as it may cause a malfunction.
Dirt, dust, scratches and warping discs will cause misoperation.
B. Notes on CD-Rs (recordable CDs)/CD-RWs (rewritable CDs):
Be sure to use discs with following marks only for the unit to play:
The unit cannot play a CD-R and CD-RW that is not finalized. (Please refer to the manual of your CD-R/CD-RW recorder or CD-R/CD-RW software for more information on finalization process).
Depending on the recording status, conditions of the disc and equipment used for the recording, some CD-Rs/CD-RWs may not be played on this unit. (see *1)*1: To have more reliable play back, please see following recommendations:a. Use CD-RWs with speed 1x to 4x and write with speed 1x to 2x.b. Use CD-Rs with speed 1x to 8x and write with speed 1x to 2x.c. Do not play a CD-RW which has been written for more than 5 times.
C. Notes on MP3 files (MP3 Version Only):
The disc must be in the ISO9660 level 1 or level 2 format, or Joliet or Romeo in the expansion format.
When naming MP3 file, be sure the file name extension is “.MP3”.
For a non-MP3 file, even though the file name extension is “.MP3”, the unit will not recognize it.
Before going through the checklist, check wiring connection. If any of the problems persist after checklist has been made, consult your nearest service dealer.
Sympton
Cause
Solution
No power
The car ignition switch is not on.
If the power supply is connected to the car accessory circuits, but the engine is not moving, switch the ignition key to “ACC”.
The fuse is blown
Replace the fuse
Disc cannot be loaded or ejected.
Presence of CD disc inside the player.
Remove the disc in the player, then put a new one.
Inserting the disc in reverse direction.
Insert the compact disc with the label facing upward.
Compact disc is extremely dirty or detective disc.
Clean the disc or try to play a new one.
Temperature inside the car is too high.
Cool off or until the ambient temperature return to normal.
Condensation
Leave the player off for an hour or so, then try again.
No sound
Volume is in minimum
Adjust volume to a desired level
Wiring is not properly connected
Check wiring connection
Sound skips
The installation angle is more than 30 degree.
Adjust the installation angle less than 30 degree.
The disc is extremely dirty or defective disc.
Clean the compact disc, then try to play a new one.
The operation keys do not work
The built-in microcomputer is not operating properly due to noise.
Press the RESET button. Front panel is not properly fixed into its place.
The radio does not work. The radio station automatic selection does not work
The antenna cable is not connected.
Insert the antenna cable firmly.
The signals are too weak.
Select a station manually.
VISIT US ONLINE:Have a question?Need service or repair?Want to leave a comment?PyleUSA.com/ContactUs
Questions? Issues?We are here to help!Phone: (1) 718-535-1800Email: [email protected]