Contact Sensor for Ring Alarm (5B28S5)Manual & Safety Instructions
Placement
Slim Magnet
First, complete the in-app setup.
- Make sure your Ring Alarm is disarmed.
- In the Ring app, tap Set Up a Device and find the Contact Sensor in the Security menu.
- Follow the in-app instructions to complete the setup.
Then, install the device in your home.
- Choose the door or window where you’d like to install your Sensor and magnet.
- If the magnet is too large, open the back and remove the magnet piece from the magnet case and mount it directly.
- Line up the Sensor and magnet, with no more than 2.5cm (1”) between them.
- Leave at least 1.3cm (1/2”) space around the Sensor so you can open the battery compartment.
- Clean the area, then peel the backing from the mounting tape and press the Sensor and magnet into place.
- To install using screws you will need: Screws: 4x 3x21mm.Anchors: 4x 5mm.
If you’re using the Contact Sensor on a door you use often, choose Main Door as the placement option. Main doors have Entry and ExitDelays to prevent you from accidentally triggering the alarm.How to change the battery.Slide the sensor backward and off the mounting bracket. Replace the battery with fresh CR2032 cell batteries. Ensure that the batteryis inserted correctly. When inserting batteries, make sure the (+) is facing up.WARNING: Inserting the battery with the wrong polarity may damage the device.
SAFETY AND COMPLIANCE INFORMATION
Use Responsibly. Read all instructions and safety information before use.
SAFETY INFORMATION
WARNING! Failure to read and follow thesesafety instructions before the operation could result in fire, electric shock, or other injury or damage. WARNING! Your device should only be used in accordance with the specific instructions for use and the intended purpose of the device. Using your device in any way other than its intended purpose could cause injury to yourself, others, and/or damage to the device or property. CAUTION! The device is not waterproof and as such should not be submerged in water, doing so could cause injury to yourself, others, and/or damage to the device.WATCH FOR SMALL PARTS! Your device and accessories may present a choking hazard to small children. Keep them out of reach of small children.Ring Contact Sensor is for indoor use only.
BATTERY SAFETYThis product contains lithium coin batteries. This device requires batteries for use. Only use new CR2032 3V batteries. Never mix old and new batteries. Keep all of the batteries out of the reach of children. Do not open, disassemble, puncture, cut, bend, shred or heat the batteries and do not allow metal objects to touch the battery terminals on the device as they can become hot and cause burns. Remove all batteries if they are worn out or before storing your Device for an extended period of time.Dispose of all batteries in accordance with applicable laws and regulations and do not dispose of batteries by throwing them into a fire.If any batteries begin to leak, take steps to prevent the fluid from coming into direct contact with skin or clothes as the fluid could be corrosive and may be toxic. Remove the batteries and clean the battery compartment in accordance with the battery manufacturer’s recommendations. CAUTION! The danger of explosion if the battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of the used batteries according to the manufacturer’s instructions. CHEMICAL BURN HAZARD! This product contains lithium coin batteries. Do not ingest batteries. If the coin cell battery is swallowed, it can cause severe internal burns in just 2 hours and lead to death. Keep all of the batteries out of the reach of children. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.
PRODUCT SPECIFICATIONSModel Number: 5B28S5Electrical Rating: 2x CR2032 3VTemperature Rating: 0°C – 49°CEU CONFORMITYHereby, Ring LLC, declares that the radio equipment Ring Contact Sensor (5B28S5) is in compliance with Directive 2014/53/EU. Thefull text of the EU Declarations of Conformity are available at the following internet address: ring.com/doc.pdf.RADIOFREQUENCY COMPLIANCEIn order to protect human health, this device meets the thresholds for exposure of the general public to electromagnetic fields according to Council Recommendation 1999/519/EC. This device should be installed and operated with at least 20 cm between the radiator and your body.Wireless Features: Z-WaveMaximum Equivalent Isotropically Radiated Power: 868.40 – 869.85 MHz 4.38 dBm EIRP
RECYCLING YOUR DEVICE PROPERLYIn some areas, the disposal of certain electronic devices is regulated. Make sure you dispose of or recycle, your device in accordance with your local laws and regulations.
MANUALSFind online manuals at: ring.com/alarm-manual
WARRANTYFind warranty information at: ring.com/warranty
Z-WAVEFor Z-Wave technical information, visit: ring.com/z-wave
UK +44 1727 26 3045EU +800 8700 9781
RingSingel 5421017 AZ AmsterdamThe Netherlands© 2021 Ring LLC or its affiliates.Ring and all related marks are trademarks of Ring LLC or its affiliates.
report this ad
References
[xyz-ips snippet=”download-snippet”]