TELTONIKA Plug and Play Tracker User Manual

FMP100

Plug and Play tracker

Quick ManualV1.4

Know your device

Side view                                             Front view (with cover)

 

Figure 1 FMP100 device view (With covers)

3

Know your device

Top view (without cover)                       Front view (without cover)

   

4

Set up your device

How to insert Nano-SIM card

1. Insert the SIM tray removal tool into the hole on the SIM card tray and then push until the tray pops out.2. Insert Nano-SIM card as shown with PIN request disabled or read our Wiki how to enter it later in Teltonika Configurator. Make sure that Nano-SIM card is fitted properly into the tray.3. Insert the SIM card tray back.4. After configuration, see “PC Connection (Windows)”.

Device is ready to be mounted.

1

Figure 3 SIM tray removal

2

Figure 3 Nano-SIM card insert

3

Figure 4 SIM tray insert

5

PC Connection (Windows)

• Connection by using Bluetooth:1) Power-up FMP100 with DC voltage (12 ­ 30 V) power supply. LED’s should start blinking, see “Error! Reference source not found.”.2) FMP100 Bluetooth is enabled by default. Turn on Bluetooth on your PC, then select Add Bluetooth or other device > Bluetooth. Choose your device named ­ “FMBxxx_last_7_imei_digits”, without LE in the end. Enter default password 5555, press Connect and then select Done.

• If Bluetooth connection is not possible, please refer to the FMP100 Wiki page on how to open the device casing and connect it via Micro-USB.

Configuration (Windows)

At first FMP100 device will have default factory settings set. These settings should be changed according to the user’s needs. Main configuration can be performed via Teltonika Configurator software. Get the latest Configurator version from here. Configurator operates on Microsoft Windows OS and uses prerequisite MS .NET Framework. Make sure you have the correct version installed.

Table 1 MS .NET requirements
MS .NET REQUIREMENTS
Operating system MS .NET Framework version Version Links
Windows VistaWindows 7Windows 8.1Windows 10 MS .NET Framework 4.6.2 32 and 64 bit www.microsoft.com

Downloaded Configurator will be in compressed archive. Extract it and launch Configurator.exe. After launch software language can be changed by clicking in the right bottom corner (Figure 5 Language selection).

6

 

Figure 5 Language selection

Configuration process begins by pressing on connected device (Figure 6 Device connected via Bluetooth).

Figure 6 Device connected via Bluetooth

After connection to Configurator Status window will be displayed (Figure 7 Configurator Status window).

Figure 7 Configurator Status window

Various Status window tabs display information about GNSS, GSM, I/O, Maintenance and etc. FMP100 has one user editable modification of configuration the changes need to be saved to device using Save to device button. Main buttons offer following functionality:

1.   Load from device –­ loads configuration from device.2.   Save to device ­- saves configuration to device.3.   Load from file –­ loads configuration from file.4.   Save to file ­- saves configuration to file.5.   Update firmware ­- updates firmware on device.6. Read records –­ reads records from the device.7.   Reboot device –­ restarts device.8.   Reset configuration –­ sets device configuration to default.

Most important configurator section is GPRS –­ where all your server and GPRS settings can be configured and Data Acquisition -­ where data acquiring parameters can be configured. More details about FMP100 configuration using Configurator can be found in our Wiki.

7

Quick SMS configuration

Default configuration has optimal parameters present to ensure best performance of track quality and data usage.

Quickly set up your device by sending this SMS command to it:

” setparam 2001:APN;2002:APN_username;2003:APN_password;2004:Domain;2005:Port;2006:0″

Note: Before SMS text, two space symbols should be inserted.

GPRS settings:• 2001 ­ APN• 2002 ­ APN username (if there are no APN username, empty field should be left)• 2003 ­ APN password (if there are no APN password, empty field should be left)

Server settings:• 2004 ­ Domain• 2005 ­ Port• 2006 ­ Data sending protocol (0 ­- TCP, 1 ­- UDP)

Default configuration settings

Movement and ignition detection:

 

Vehicle movement will be detected by accelerometer

 

Ignition will be detected by vehicle power voltage between 13,2-30 V

Device makes a record On Moving if one of these events happen:

 

300 seconds passes

 

Vehicle turns 10 degrees

 

Vehicle drives 100 meters

Speed difference between last coordinate and current position is greater than 10 km/h

Device makes a record On Stop if:

 

1 hour passes while vehicle is stationary and ignition is off

Records sending to server:

If device has made a record it is sent to the server every 120 seconds

After successful SMS configuration, FMP100 device will synchronize time and update records to configured server.Time intervals and default I/O elements can be changed by using Teltonika Configurator or SMS parameters.

8

User Interface

Table 3 User interface LED indication scenarios
SCENARIO INDICATION MEANING
GSM error Red LED 500 ms blink 3 times + Buzzer SIM is not inserted, device can’t connect to the operator or GSM signal is being jammed
No GNSS fix Red LED 1000 ms blink 1 time Device doesn’t have valid GNSS fix and is searching for coordinates
GNSS fix Green LED 1000 ms blink 1 time Device has valid GNSS fix
Key pressed 1000 ms interval Buzzer while active Key is pressed and held
Private Trip Green LED 500 ms blink 3 times + Buzzer Battery is almost fully discharged
Business Trip Blue LED 500 ms blink 3 times + Buzzer Indication used to remind the user that device is still operational

Note! This table contains only the default scenarios. Additional scenarios/default ones can be modified using Teltonika Configurator. User is able to select different indication color (Red, Green or Blue), frequency of LED blinking and buzzer status.

Keyboard

Table 4 Keyboard default actions
ACTION FUNCTION
1 Click Check Trip Mode
2 Clicks Change Trip Mode
Long Click Alarm

Basic characteristics

Table 5 Basic characteristics
MODULE
Name Teltonika TM2500
Technology GSM/GPRS/GNSS/BLUETOOTH
GNSS
GNSS GPS, GLONASS, GALILEO, BEIDOU, SBAS, QZSS, DGPS, AGPS
Receiver 33 channel
Tracking sensitivity -165 Dbm
Position accuracy < 2.5 CEP
Velocity accuracy < 0,1 m/s (within +/- 15% error)
Hot start < 1 s
Warm start < 25 s
Cold start < 35 s

9

CELLULAR
Technology GSM
2G bands Quad-band 850 / 900 / 1800 / 1900 MHz
Data transfer GPRS Multi-Slot Class 12 (up to 240 kbps)
Data support SMS (text/data)

 

POWER
Input voltage range 10 – 30 V DC with overvoltage protection
Back-up battery 3.7 V 170 mAh (0.63 Wh)
Power consumption At 12V < 5 mA (Ultra Deep Sleep)At 12V < 7 mA (Deep Sleep)At 12V < 7 mA (Online Deep Sleep)At 12V < 8 mA (GPS Sleep)At 12V < 28 mA (nominal)
BLUETOOTH
Specification 4.0 + LE
Supported peripherals Temperature and Humidity sensor, Hands-free headset, Inateck Barcode Scanner, Universal BLE sensor support
INTERFACE
Connection Cigarette lighter socket
Configurable buttons 1
GNSS antenna Internal High Gain
GSM antenna Internal GSM High Gain
USB 1 x USB 2.0 Micro-USB for configuration1 x USB type A for external device charging (5V 1A)
LED indication RGB LED
SIM Nano-SIM
Memory 128MB internal flash memory
PHYSICAL SPECIFICATION
Dimensions 96,7 x 33,4 x 27,5 mm (L x W x H)
OPERATING ENVIRONMENT
Operating temperature (without battery) -40 °C to +85 °C
Storage temperature (without battery) -40 °C to +85 °C
Operating humidity 5% to 95% non-condensing
Ingress Protection Rating IP41
Battery charge temperature 0 °C to +45 °C
Battery discharge temperature -20 °C to +60 °C
Battery storage temperature -20 °C to +45 °C for 1 month-20 °C to +35 °C for 6 months
FEATURES
Sensors Accelerometer
Scenarios Green Driving, Over Speeding detection, Jamming detection, GNSS Fuel Counter, Excessive Idling detection, Unplug detection, Towing detection, Crash detection, Auto Geofence, Manual Geofence, Trip
Sleep modes GPS Sleep, Online Deep Sleep, Deep Sleep, Ultra Deep Sleep
Configuration and firmware update FOTA Web, FOTA, Teltonika Configurator (USB, Bluetooth), FMBT mobile application (Configuration)
SMS Configuration, Events, Debug
GPRS commands Configuration, Debug
Time Synchronization GPS, NITZ, NTP
Fuel monitoring OBDII
Ignition detection Accelerometer, External Power Voltage

11

Safety information

This message contains information on how to operate FMP100 safely. By following these requirements and recommendations, you will avoid dangerous situations. You must read these instructions carefully and follow them strictly before operating the device!

  • The device uses SELV limited power source. The nominal voltage is +12 V DC. The allowed voltage range is +10…+30 V DC.
  • To avoid mechanical damage, it is advised to transport the device in an impact-proof package. Before usage, the device should be placed so that its LED indicators are visible. They show the status of device operation.
  • Before unmounting the device from vehicle, ignition MUST be OFF.

Do not disassemble the device. If the device is damaged, the power supply cables are not isolated or the isolation is damaged, DO NOT touch the device before unplugging the power supply.

All wireless data transferring devices produce interference that may affect other devices which are placed nearby.

 The programming must be performed using a PC with autonomic power supply.

 

Installation and/or handling during a lightning storm is prohibited.

 

The device is susceptible to water and humidity.

Teltonika is not responsible for any harm caused by wrong cables used for connection between PC and FMP100

WARNING! Do not use FMP100 device if it distracts driver or causes inconvenience due to cigarette lighter socket placement. Device must not interfere with driver.

Battery should not be disposed of with general household waste. Bring damaged or worn-out batteries to your local recycling center or dispose them to battery recycle bin found in stores.

12

Certification and Approvals

This sign on the package means that it is necessary to read the User`s Manual before your start using the device. Full User`s Manual version can be found in our Wiki.

This sign on the package means that all used electronic and electric equipment should not be mixed with general household waste.

 

Hereby, Teltonika declare under our sole responsibility that the above described product is in conformity with the relevant Community harmonization: European Directive 2014/53/EU (RED).

13

Warranty

TELTONIKA guarantees its products to be free of any manufacturing defects for a period of 24 months. With additional agreement we can agree on a different warranty period, for more detailed information please contact our sales manager.

Contact us teltonika.lt/company/contacts

All batteries carry a reduced 6 month warranty period.

If a product should fail within this specific warranty time, the product can be:

  • Repaired
  • Replaced with a new product
  • Replaced with an equivalent repaired product fulfilling the same functionality
  • TELTONIKA can also repair products that are out of warranty at an agreed cost.

Warranty Disclaimer

TELTONIKA PRODUCTS ARE INTENDED TO BE USED BY PERSONS WITH TRAINING AND EXPERIENCE. ANY OTHER USE RENDERS THE LIMITED WARRANTIES EXPRESSED HEREIN AND ALL IMPLIED WARRANTIES NULL AND VOID AND SAME ARE HEREBY EXCLUDED. ALSO EXCLUDED FROM THIS LIMITED WARRANTY ARE ANY AND ALL INCIDENTAL OR CONSEQUENTIAL DAMAGES INCLUDING BUT NOT LIMITED TO, LOSS OF USE OR REVENUE, LOSS OF TIME, INCONVENIENCE OR ANY OTHER ECONOMIC LOSS.

More information can be found at teltonika.lt/warranty-repair

14

References

[xyz-ips snippet=”download-snippet”]

Posted

in

by

admin

Tags:

, ,