TELTONIKA RUTX12 4G Router User Guide

RUTX12Quick Start Guide v1.2

https://wiki.teltonika-networks.com/

FRONT VIEW

BACK VIEW

POWER SOCKET PINOUT

HARDWARE INSTALLATION

  1. Pull out the SIM needle from the front panel of the router and push the SIM holder button with the SIM needle.
  2. Pull out the SIM holder.
  3. Insert your SIM card into the SIM holder.
  4. Slide the SIM holder back into the router.
  5. Attach all antennas.
  6. Connect the power adapter to the socket on the front of the device. Then plug the other end of the poweradapter into a power outlet.
  7.  Connect to the device wirelessly using SSID and password provided on the device information label or use an Ethernet cable connected to the LAN port.

LOGIN TO DEVICE

  1. To enter the router’s Web interface (WebUI), type http://192.168.1.1 into the URL field of your Internet browser.
  2. Use login information shown in image A when prompted for authentication.
  3. After you log in, you will be prompted to change your password for security reasons. The new password must contain at least 8 characters, including at least one uppercase letter, one lowercase letter, and one digit. This step is mandatory, and you will not be able to interact with the router’s WebUI before you change the password.
  4. When you change the router’s password, the Configuration Wizard will start. The Configuration Wizard is a tool used to set up some of the router’s main operating parameters.
  5. Go to the Overview page and pay attention to the Signal Strength indication (image B). To maximize the cellular performance try adjusting the antennas or changing the location of your device to achieve the best signal conditions.

TECHNICAL INFORMATION

Radio specifications
RF technologies 3G, 4G, GNSS, WiFi, BLE
Max RF power 24 , 23 , 23 10
Bundled accessories specifications*
Power adapter Input: 0.6 VAC, Output: 12 VDC, 1.5 A, 4 pin plug
Mobile antenna 698~960 / 1710~2690 MHz, 50 Ω, VSWR<3, gain** 3 dBi, omnidirectional, SMA male connector
GNSS antenna 1575.42~1602 MHz, 2.2~5 VDC, VSWR<1.5, active total gain** 28 dB (typ.), RHCP polarization, SMA male connector
WiFi antenna 2400~2500 MHz / 5100~5950 MHz, 50 Ω, VSWR<2.5, gain** 3.5 dBi, omnidirectional, RP-SMA male connector
BLE antenna 2400~2500 MHz, 50 Ω, VSWR<2.5, gain** 2.5 dBi, omnidirectional, RP-SMA male connector

*Order code dependent.**Higher gain antenna can be connected to compensate for cable attenuation when a cable is used. The user is responsible for compliance with the legal regulations.In all EU member states, the operation of 5150-5250 MHz is restricted to indoor use only.

SAFETY INFORMATION

RUTX12 router must be used in compliance with any and all applicable national and international laws and with any special restrictions regulating the utilization of the communication module in prescribed applications and environments.

The full text of the EU declaration of conformity is available at the following Internet address: https://wiki.teltonika-networks.com/view/RUTX12_CE/RED

Instruction Manual: Connect the power adapter to turn on the device. Open 192.168.1.1 in your web browser to configure it. More information on https://wiki.teltonika-networks.com/

This sign means that all used electronic and electric equipment should not be mixed with general household waste.

This sign means that the product meets the requirements of the applicable EU directives.

www.teltonika-networks.com2021 Teltonika Networks©

References

[xyz-ips snippet=”download-snippet”]

Posted

in

by

admin

Tags:

, ,