NetworksQuick Start Guide v1.3Wiki knowledge basehttps://wiki.teltonika-networks.com/https://scnv.io/BbOw?qr=1
FRONT VIEWBACK VIEWINPUT/OUTPUT CONNECTOR PINOUTPOWER SOCKET PINOUT
POWER SOCKET PINOUT
- Unscrew two back panel hex bolts and remove the back panel.
- Insert your SIM card into the SIM socket.
- Attach the panel and tighten the hex bolts.
- Attach the mobile antenna (max torque 0.4 N·m / 3.5 lbf·in).
- Connect the USB cable.
DI1 and DI2 are DRY/WET configurable inputs. WET: 0-1.9 V is detected as logical “0”, 1.9-3.8 V is detected as logical “1”. DRY: Logical “0” is detected when input is shorted to GND, otherwise, input is detected as logical “1”.NC*, C*, and NO* are respectively Normally Closed, Common, and Normally Open contacts of internal Relays 1 and 2. Maximum Relay 1 (Non-latching) ratings: 0.5 A at 60 VDC/70 VAC, 1 A at 30 VDC/VAC. Maximum Relay 2 (Latching) ratings: 0.8 A at 70 VDC, 0.9 A at 70 VAC, 2 A at 30 VDC/VAC.A is ADC input. Analog voltage range 0-30 V. Input can be configured for 4-20mA sensor protocol as a current measurement of 0-30 mA.I and are isolated input contacts. 0-7.3 V is detected as logical “0”, 7.3-71 V is detected as logical “1”.+ is power output connected directly to the gateway’s power supply input pin. This Output can be used for powering external 4-20 mA current sensor.3.8 is 3.8V power output which can be used to power 1-Wire sensors when needed.1W 1-Wire protocol input/output.
- Power on the device and connect the USB cable to your computer.
- Allow the gateway to boot up. This might take up to 30 seconds.
- Your computer’s OS should detect the USB device and install the driver.
- To enter the gateway’s Web interface (WebUI), type http://192.168.2.1 into the URL field of your Internet browser.
- Use login information shown in image A when prompted for authentication.
- After logging in pay attention to the Signal Strength indication displayed in the Mobile widget (image B). To maximize the cellular performance try adjusting the antennas or changing the location of your device to achieve the best signal conditions.
A
B
MOBILE |
|
Data connection |
Connected |
State |
Registered (home); OPERATOR; 4G (LTE) |
SIM card slot in use |
Ready |
Bytes received/sent |
348.7 KB / 223.5 KB |
TECHNICAL INFORMATION
Radio specifications |
|
RF technologies | 2G, 3G, 4G |
Max RF power | 33 , 24 , 23 |
Bundled accessories specifications* |
|
Power adapter | Input: 0.4 VAC, Output: 9 VDC, 0.5 A, 4-pin plug |
Mobile antenna | 698~960 / 1710~2690 MHz, 50 Ω, VSWR<2, gain** 2 dBi, omnidirectional, SMA male connector |
*Order code dependent.**Higher gain antenna can be connected to compensate for cable attenuation when a cable is used. The user is responsible for compliance with the legal regulations.
SAFETY INFORMATION
TRB141 gateway must be used in compliance with any and all applicable national and international laws and with any special restrictions regulating the utilization of thecommunication module in prescribed applications and environments.Hereby, TELTONIKA declares that this TRB141 is in compliance with the essential requirements and other relevant provisions ofDirective RED.The full text of the EU declaration of conformity is available at the following internet address: https://wiki.teltonika-networks.com/view/TRB141_CE/REDPower socketInstruction Manual: Connect the power adapter to turn on the device. Open 192.168.2.1 in your web browser to configure it. More information onhttps://wiki.teltonika-networks.com/For more information visit www.teltonika-networks.com
©2020 Teltonika
References
[xyz-ips snippet=”download-snippet”]