WEISER
67377-001Rev 02GED1850
Installation and User Guide
Weiser1-800-501-9471www.weiserlock.com
Weiser1-800-501-9471
1 Prepare the door and check dimensions
If drilling a new door, use the supplied template and the complete door drilling instructions available at weiserlock.com/doorprep
A Make sure your door is compatible. If you have a standard deadbolt mounted separately from the handle below it, your door is compatible.
B Make sure your door is compatible.
C Measure to confirm that the hole in the door is either 2-1/8″ (54 mm) or 1-1/2″ (38 mm).
Note: Additional door preparation may be required for doors with 1-1/2″ (38 mm) holes. Consult the deadbolt drilling instructions at weiserlock.com/doorprep
D Measure to confirm that the backset is either 2-3/8″ or 2-3/4″ (60 or 70 mm).
E Measure to confirm that the hole in the door edge is 1″ (25 mm).
F Measure to confirm that the door is between 1-3/8″ and 2″ (35 mm and 51 mm) thick.
2 Install the latch and strike
A Is the door edge chiseled?
B Hold the latch in front of the door hole, with the latch face flush against the door edge.
C Is the D-shaped hole centered in the door hole?
D Which latch are you installing?
E Install the strike on the door frame.
Make sure the hole in the door frame is drilled a minimum of 1″ (25 mm) deep.
3 Install the exterior keypad
A What is the diameter of the hole in the door?
4 Install the interior assembly
A Ensure the turnpiece shaft is pointing up, and remove the interior cover and battery pack from the interior assembly.
B Install the interior assembly onto the mounting plate.
5 Install the batteries and perform the door handing process
This step will teach your lock the orientation of your door and is crucial to lock operation.
A Install 4 AA batteries in the battery pack.
B With the door open, install the battery pack to initiate auto-handing.
C The latch will retract and extend to learn the orientation of the door.
D The Status LED will indicate success or failure.
6 Test the lock and check door alignment
A With the door open, insert the key to extend the latch. Ensure that the latch extends smoothly.
B Turn the key 180° to retract the latch. Ensure that the latch retracts smoothly.
C Close the door. Insert and rotate the key to lock the door. Ensure that the door locks smoothly.
D Turn the key 180° to retract the latch. Ensure that the door unlocks smoothly.
If your door does not lock and unlock smoothly, make sure you replaced your previous latch and strike with those supplied in the box. If you still experience locking errors, call Weiser Support to order a Warped Door Service Kit. Weiser Support: 1-800-501-9471
7 Install the interior cover
Important Information about the interior cover
The window on the interior cover is unlocked by default for easier access to the battery pack and buttons.
For additional security, you may choose to lock the window by installing the security screw.
When the window is locked, you will need to remove the entire interior cover and screws to access the battery pack and buttons.
Cover Installation
Battery Pack Access
8 Download the app and create an account
The Weiser app is needed to use this lock. If this lock was professionally installed (or installed by someone other than the homeowner), make sure this step is performed by the homeowner.
A Download the Weiser app by scanning the QR code or visiting www.weiserlock.com/app on your smartphone.
B Create your account and follow the setup instructions in the Weiser app.
Reference Guide
SmartCode at a Glance
System Alerts
Status LED colors
These features can be adjusted in some smart home apps.
Manual Door Handing
If needed, the door handing process can be initiated manually. This is useful if the lock is beingmoved to a different door.
Network Reset
Network Reset will delete all Bluetooth pairings from the lock including Admins and Members.
System Reset
System Reset will delete all access codes and lock settings including lock handing. The lock will run the handing process at the end of the System Reset.
Factory Reset
Factory Reset will delete all access codes, Bluetooth pairings including Admins and Members, and lock settings including lock handing. The lock will run the handing process at the end of the Factory Reset.
Troubleshooting
A complete Aura Bluetooth Keypad Programming and Troubleshooting Guide is available at www.weiserlock.com/aura/support
SmartKey Re-Keying
Re-key the lock to work with your existing key. See the supplied SmartKey Re-key instructions for more information.
Note: If Auto-Lock is enabled, remove the battery pack before re-keying your lock.
Important Safeguards
1. Read all instructions in their entirety.2. Familiarize yourself with all warningand caution statements.3. Remind all family members of safety precautions.4. Protect your user codes.5. Dispose of used batteries according to local laws and regulations.
WARNING: This Manufacturer advises that no lock can provide complete security by itself. This lock may be defeated by forcible or technical means or evaded by entry elsewhere on the property. No lock can substitute for caution, awareness of your environment, and common sense. Builder’s hardware is available in multiple performance grades to suit the application. In order to enhance security and reduce risk, you should consult a qualified locksmith or other security professional.
Aura Bluetooth Keypad Smart Lock GED1850 User Manual – Aura Bluetooth Keypad Smart Lock GED1850 User Manual –