SmartCode 5 Touchpad Electronic Lever GED1455 User Manual

Installation and User Guide

Parts in the box

Prepare the door and check dimensions

If drilling a new door, use the supplied template and the completedoor drilling instructions available at www.weiserlock.com/doorprep.

Measure to confirm that the hole inthe door is 2-1/8″ (54 mm).

Measure to confirm that the backset iseither 2-3/8″ or 2-3/4″ (60 or 70 mm).

Measure to confirm that the hole inthe door edge is 1″ (25 mm).

Measure to confirm that the dooris between 1-3/8″ and 1-3/4″ (35 mmand 44 mm) thick.

Install the latch and strike

Hold the latch in front of the door hole, with the latchface flush against the door edge.

Are the latch holes centered in the door hole?

Adjust the latch face (if needed).

Is the door edge chiseled?

Install strike on the door frame.

Install the exterior keypad, mounting plate, and spindle

Install exterior keypad.

Route cable through mounting plate.

Secure mounting plate withsupplied screws.

Install spindle.

Install batteries and pair the lock with your smart home system

Remove battery cover and battery pack from interior assembly

Install 4 AA batteries in battery pack.

Install battery pack.

Initiate the pairing process at yoursmart home controller. Refer to your smarthome system instructions for more information.

Hold the interior assembly a maximum of 12″ (305 mm) Gfrom your smart home controller. When prompted byyour smart home system to initiate pairing at the lock,press button “A” on the lock interior one time.

The lock and controller must remain stationary for atleast 60 seconds during the pairing process.

If pairing is successful, re-name thelock in your system (if applicable).Then, remove battery pack.

If pairing is unsuccessful, followyour system’s instructions toremove the lock from any othernetwork, then press button “A”on the lock one time.Repeat steps 4D and 4E.If still unsuccessful, consultthe Programming andTroubleshooting Guide on theSmartCode 5 Lever page atwww.weiserlock.com.

Install interior assembly

Connect cable.

Install battery pack.

Push interior assemblyonto mounting plate.

Secure with screws.

Install levers

Install interior lever.

Secure interior lever.

Install exterior lever.

Secure exterior lever.

Test latch operation

Close door, test latch operation and make adjustments as needed:

The small bolt of the latch should not enter the strikehole. If it enters the strike hole, reposition strike

If latch is loose in the strike, adjust the strike tab so itgrips the latch bolt better when the door is closed.

Add user codes (30 max)

It is recommended that you add anddelete all user codes through your smarthome control system. If your systemdoes not allow this, codes may be addeddirectly to the lock as shown here.Programming TimeoutIf no button is pressed for 5 seconds, thesystem will time out and you will need torestart the procedure.

Make sure the door is open. Pressthe Program button the number oftimes that corresponds to the usercode position being programmed.

Enter user code. A total of 30 usercodes may be programmed.

Press Lock button once

What lights and sounds does the lock produce?

*Beeping sound will only be heard if switch #3 (on the lock interior) is in the on positon. See “Switches and Status LED Colors” on page 4.

MastercodeFor enhanced security, a mastercode may be used when adding and deleting user codes. For more information about the mastercode, download the Programmingand Troubleshooting Guide on the SmartCode 5 Lever page at www.weiserlock.com.

Test the lock (review normal operation)

Confirm that the code(s) added in previous step can unlock the door.

Re-key the lock (if needed) and install the battery cover

Re-key the lock (if needed).

Install the battery cover.

Reference Guide

SmartCode at a Glance

Switches and Status LED colors

Battery Replacement

If another lock is installed above the lever, remove the interiorassembly when battery replacement is required.

Network Information

Adding the lock to the network During the pairing process, press button “A” on the lockinterior once.

Removing the lock from the networkFollow your smart home system’s instructions to removethe lock from the network. When prompted by thesystem, press button A” on the lock interior once.

Z-Wave System Notes

This product is a security enabled Z-wave product and must be used with a Security Enabled Z-Wave controller to be fullyutilized. Z-Wave is a “Wireless mesh network,” and results may vary based on building construction and communication path,with 35 feet+ being typical installed distance from smart home controller. It may be necessary to install additional Z-Wavebeaming capable devices that can serve as repeaters to enhance the communication path between the lock and controllerfor a more robust Z-Wave network.To assure interoperability, each Z-Wave product must pass a stringent conformance test to assure that it meets the Z-Wavestandard for complete compliance with all other devices and controls. The Z-Wave identity mark assures consumers,integrators, dealers and manufacturers that their products will reliably perform with any other Z-Wave device. And,regardless of the vendor, always powered nodes may act as a repeater for Kwikset/Weiser/Baldwin products.Z-Wave Configuration and Association Parameters are available on the SmartCode 5 Lever page at www.weiserlock.com.

System Alerts

Deleting a user code

In order to delete a user code, you must override the code by adding a diff erent user code in the sameposition. For example, if you want to delete the third code, add a diff erent user code in position three.

Test the old user code to make sure it can no longer unlock the door.If you cannot remember the user code position, you may wish to perform a factory reset to delete allcodes associated with the lock.

Troubleshooting

A complete Programming and Troubleshooting Guide is available onthe SmartCode 5 Lever page at www.weierlock.com.

Factory Reset

A factory reset will delete all codes associated with the lock,and it will remove it from your smart home system..

Important Safeguards

Read all instructions in their entirety.
Familiarize yourself with all warning and caution statements.
Remind all family members of safety precautions.
Protect your user codes and mastercode.
Dispose of used batteries according to local laws and regulations.

CAUTION: Prevent unauthorized entry. Since anyone with access to the back panelcan change the user codes, you must restrict access to the back panel and routinelycheck the user codes to ensure they have not been altered without your knowledge.The use of a mastercode can help protect your system’s settings.

WARNING: This Manufacturer advises that no lock can provide complete securityby itself. This lock may be defeated by forcible or technical means, or evaded byentry elsewhere on the property. No lock can substitute for caution, awareness ofyour environment, and common sense. Builder’s hardware is available in multipleperformance grades to suit the application. In order to enhance security and reducerisk, you should consult a qualified locksmith or other security professional.