63995 / 01 , GED1490, Stand-Alone
Installation and User Guide
WeiserUSA: 1-800-677-5625Canada: 1-800-501-9471www.weiserlock.com
1 Prepare the door and check dimensions
If drilling a new door, use the supplied template and the complete door drilling instructions available at www.weiserlock.com/doorprep.
A Measure to confirm that the hole in the door is either 2-1/8″ (54 mm) or 1-1/2″ (38 mm).
Note: Additional door preparation may be required for doors with 1-1/2″ (38 mm) holes. Consult the deadbolt drilling instructions at www.weiserlock.com/doorprep.
B Measure to confirm that the backset is either 2-3/8″ or 2-3/4″ (60 or 70 mm).
C Measure to confirm that the hole in the door edge is 1″ (25 mm).
D Measure to confirm that the door is between 1-3/8″ and 1-3/4″* (35 mm and 44 mm*) thick.
*Service kits for 2-1/4″ (57 mm) thick doors are available through Weiser.
2 Prepare
A Is the door edge chiseled?
B Hold the latch in front of the door hole, with the latch face flush against the door edge.
C Are the latch holes centered in the door hole?
D Which latch are you installing?
E Install strike on the door frame.
3 Install the exterior keypad
A Insert cylinder into keypad.
B What is the diameter of the hole in the door?
C Install exterior keypad and mounting plate.
4 Install the interior assembly
A Remove battery cover.
B Remove battery pack.
C Make sure the turn piece is in the vertical position.
D Connect cable. Ensure tight cable connection.
E Lay cable flat against the interior housing.
F Push turnpiece shaft onto torque blade.
G Secure interior assembly with supplied screws.
5 Install the batteries and perform the door handing process
This step will teach your lock the orientation of your door and is crucial to lock operation.
A Install 4 AA batteries in battery pack.
B Press and HOLD the Lock button while installing battery pack.
Hold button until the latch bolt starts moving on its own.
C Did the latch bolt retract and extend on its own when the battery pack was installed?
6 Add user codes (8 max)
Programming TimeoutIf no button is pressed for five seconds, the system will time out and you will need to restart the procedure.
A Make sure the door is open. Press the Program button the number of times that corresponds to the user code position being programmed.
B Enter user code. A total of 8 user codes may be programmed.
C Press Lock button once.
D What lights and sounds does the lock produce?
*Beeping sound will only be heard if switch #3 (on the lock interior) is in the on positon. See “Switches and Status LED Colors” on page 4.
MastercodeFor enhanced security, a mastercode may be used when adding and deleting user codes. For more information about the mastercode, download the Programming and Troubleshooting Guide on the SmartCode 5 Deadbolt page at www.weiserlock.com.
7 Test the lock (review normal operation)
Confirm that the code(s) added in previous step can unlock the door.
Locking the Door
Press Lock button once.
Unlocking the Door
8 Re-key the lock (if needed) and install the battery cover
B Install the battery cover.
Reference Guide
SmartCode at a Glance
System Alerts
Switches and Status LED colors
Troubleshooting
A complete SmartCode 5 Deadbolt Programming and Troubleshooting Guide is available at www.weiserlock.com.
Deleting a user code
In order to delete a user code, you must override the code by adding a different user code in the same position. For example, if you want to delete the third code, add a different user code in position three.
Test the old user code to make sure it can no longer unlock the door.
If you cannot remember the user code position, you may wish to perform a factory reset to delete all codes associated with the lock.
Factory Reset
A factory reset will delete all codes associated with the lock, and it will remove it from your smart home system.
Important Safeguards
-
-
-
- Read all instructions in their entirety.
- Familiarize yourself with all warning and caution statements.
- Remind all family members of safety precautions.
- Protect your user codes and mastercode.
- Dispose of used batteries according to local laws and regulations.
-
-
CAUTION: Prevent unauthorized entry. Since anyone with access to the back panel can change the user codes, you must restrict access to the back panel and routinely check the user codes to ensure they have not been altered without your knowledge. The use of a mastercode can help protect your system’s settings.
WARNING: This Manufacturer advises that no lock can provide complete security by itself. This lock may be defeated by forcible or technical means, or evaded by entry elsewhere on the property. No lock can substitute for caution, awareness of your environment, and common sense. Builder’s hardware is available in multiple performance grades to suit the application. In order to enhance security and reduce risk, you should consult a qualified locksmith or other security professional.
SmartCoode 5 Touchpad Electronic Deadbolt GED1490 Instruction Manual – SmartCoode 5 Touchpad Electronic Deadbolt GED1490 Instruction Manual –