work in progress
Rapid Response Button User GuideThe Rapid Response Button is designed to improve employee safety by providing indoor location information of employees upon emergency leveraging PwC’s Indoor Geolocation Platform (IGP).
(1) Lanyard Ring(2) Left Button with LED (4) USB Port and Reset Pin(5) Recessed Area for Badge
(3) Right Button
Reserved for back image of the Device
(4a) Reset Pin (4b) USB Charging Port
(6) Device Label
(7) USB Charging Cable
(1) Lanyard RingAttach lanyard with the ring to wear the device(2) Left Button with LEDThe left button is smooth and translucent with LEDs inside it(3) Right ButtonThe right button is orange and texturedTrigger / Stop Alerts Press and hold both the left button and the right button to trigger alerts and location reports. The LED will flash when an alert is triggered.Press and hold both buttons again to stop alerts.Silent / Audible Alert ModeWhen the silent alert mode is triggered, the device will vibrate once and the LED will flash green. Once a location report is sent, the device will vibrate.When the audible alert mode is triggered, the device will beep and the LED will flash red. Once a location report is sent, the device will vibrate.Device Specs:Model: AP83 SigFox Radio Frequency Band: 902.1375MHz to 904.6625MHz WiFi Band: 2.4GHz Bluetooth Version: 4.2
If an alert is triggered and not stopped, the device will send a location report every one minuteCheck Silent / Audible Alert ModePress and release the right (orange) button. If the LED flashes green, the device is in the silent alert mode. If the LED flashes red, the device is in the audible alert modeSwitch Between Silent / Audible Alert ModesPress and hold the right (orange) button for 3 seconds to switch between silent / audible alert modesThe device will beep and flash green LED when it is switched to the silent alert modeThe device will beep and flash red LED when it is switched to the audible alert mode(4) USB Port and Reset Pin(4a) Micro USB Port for charging and device update (by device managers)(4b) Reset pin. Device can be power cycled by pressing the reset pin with a paperclip
(5) Recessed Area for BadgeOptionally stick an employee badge photo in the recessed area(6) Device LabelDevEUI: LoRa Device Extended Unique IdentifierAddress: Device MAC address Serial No. Device serial number Part No. Device part number FCC ID: Device FCC ID QR Code: Scanning of the QRcode renders a concatenated DevEUI, Address, Serial No. and Part No.(7) USB Charging CableCharging Micro USB cable for the device
Dimensions: 2.6 x 4.5 x 0.4 inch Weight: 62g Battery: 500mAh Operating Temperature: 0-45C Relative Humidity: 0-95%
Rapid Response Button User GuideCaution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: –Reorient or relocate the receiving antenna. –Increase the separation between the equipment and receiver. –Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. –Consult the dealer or an experienced radio/TV technician for help.This equipment complies with FCC`s RF radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
[xyz-ips snippet=”download-snippet”]