ZYXEL Rugged Switch User Guide

ZYXEL Rugged Switch User Guide

A. Overview

The RGS200-12P Managed Rugged switch is designed for supporting environmental hardening application. Managed switches are easier to prioritize, partition, and organize user’s network, providing a more reliable and better quality services.

B. Dimension Illustration

C. DIN-Rail Mounting

Mounting step:

  1. Screw the DIN-Rail bracket on with the bracket and screws in the accessory kit.
  2. Hook the unit over the DIN rail.
  3. Push the bottom of the unit towards the DIN Rail until it locks in place.

D. Wall Mounting

Screw the wall-mount brackets with screws in the accessory kit.E. Connecting Power Terminal Block

The switch can be powered from two power supplies (input range 12V – 58V). Insert the positive and negative wires into V+ and Vcontactson the terminal block respectively and tighten the wire-clamp screws to prevent the wires from being loosened

The DC power should be connected to a well-fused power supply.Input power should be within the range of 54~58VDC for PoE+ compliant, or 48-58VDC for PoE compliant.

EU ImporterZyxel Communication A/S Generatorvej 8D, 2860 Søborg, Denmark. http://www.zyxel.dk

F. Alarm Relay and Ground

The alarm relay output contacts are in the middle of the DC terminal block connector as shown in the figure below. The alarm relay out is “Normal Open”, and it will be closed when detected any predefined failure such as power failures or Ethernet link failures. The relay output with current carrying capacity of 0.5A @ 24 VDC

G. Console Connection

  • DB9 connector connect to computer COM port
  • Baud rate: 115200bps
  • 8 data bits, 1 stop bit
  • No Parity
  • None flow control

H. Connect & Login to Managed Switch

  1. Connecting to the Ethernet port (RJ45 Ethernet port) of Managed Switch.
  2. Factory default IP: 192.168.1.1
  3. Login with default account and password. Username: admin Password: 1234

This equipment is intended to be used in a Restricted Access Location, with access limited to SERVICE PERSONAL and USERS authorized to be in that location.

US ImporterZyxel Communications, Inc 1130 North Miller Street Anaheim, CA 92806-2001 http://www.us.zyxel.comCopyright © 2016 Zyxel Communications Corp. All Rights Reserved

A. The RGS200-12P Managed Rugged switch is designed for supporting environmental hardening application. Managed switches are easier to prioritize, partition, and organize user’s network, providing a more reliable and better quality services.

C. Mounting step:

  1. Screw the DIN-Rail bracket on with the bracket and screws in the accessory kit.
  2. Hook the unit over the DIN rail.
  3. Push the bottom of the unit towards the DIN Rail until it locks in place.

D. Screw the wall-mount brackets with screws in the accessory kit.E. The switch can be powered from two power supplies (input range 12V– 58V). Insert the positive and negative wires into V+ and V- contacts on the terminal block respectively and tighten the wire-clamp screws toprevent the wires from being loosened.

  • The DC power should be connected to a well-fused power supply.
  • Input power should be within the range of 54~58VDC for PoE+ compliant, or 48-58VDC for PoE compliant.

F. The alarm relay output contacts are in the middle of the DC terminal block connector as shown in the figure below. The alarm relay out is “Normal Open”, and it will be closed when detected any predefined failure such as power failures or Ethernet link failures. The relay output with current carrying capacity of 0.5A @ 24 VDCG. DB9 connector connect to computer COM port. Baud rate: 115200bps. 8 data bits, 1 stop bit. No Parity. None flow control.H. 1. Connecting to the Ethernet port (RJ45 Ethernet port) of Managed Switch. 2. Factory default IP: 192.168.1.1 3. Login with default account and password. Username: admin / Password: 1234

 

 

Read More About This Manual & Download PDF:

References

[xyz-ips snippet=”download-snippet”]

Posted

in

by

admin

Tags:

, ,