Category: METER
-
AQUALAB TDL Water Activity Meter User Guide
AQUALAB TDL Water Activity Meter User Guide AQUALAB TDL QUICK START Preparation Inspect and verify that all AQUALAB TDL components arrived in good condition. Select a clean, level location where the temperature is stable. Locations with high temperature variability (e.g., next to air conditioners, heater vents, or open windows) can affect the accuracy of readings.…
-
SC-1 Leaf Porometer User Guide
SC-1 Leaf Porometer ® SC-1LEAF POROMETERSC-1 QUICK START10243-06 6.30.2020 Preparation Confirm that SC-1 components are intact. Connect the SC-1 sensor head to the SC-1 controller with the serial port and install the batteries into the SC-1 controller. Fill the black desiccant chamber approximately 3/4 full with fresh desiccant. Orient the black desiccant chamber vertically so…
-
METER TEMPOS Thermal Properties Analyzer User Guide
METER TEMPOS Thermal Properties Analyzer User Guide TEMPOS QUICK START Preparation Confirm that TEMPOS components are intact, including the selected sensors. Read the full TEMPOS Manual at metergroup.com/tempos-support. All products have a 30-day satisfaction guarantee. Sample Considerations Measurements are best taken in a thermally stable environment such as a Styrofoam box. Avoid outside sources of…
-
METER TEROS 06 Soil Temperature Profile Probe User Guide
METER TEROS 06 Soil Temperature Profile Probe Preparation Confirm that TEROS 06 components are intact. For installation, gather the TEROS 06 Auger, a dead blow hammer, pvc casing or flexible conduit, a cable inserting tool, a spade, and a level.Determine the desired installation location, avoid roots and rocks, and mark the drilling depth (104 cm…
-
TEROS 31 Tensiometer User Guide
TEROS 31 Tensiometer Preparation Confirm TEROS 31 components are intact. For installation, gather the tensiometer auger, a refilling syringe (purchased separately), a refilling rack (purchased separately), and deionized water.Determine the desired installation angle and calculate the corresponding installation depth. METER recommends conducting a system check with a logger prior to installation. NOTE: A barometric reference…
-
METER AQUALAB 3 One Minute Water Activity User Guide
AQUALAB 3 AQUALAB 3 QUICKSTART PreparationConnect the Apple®iPad®mobile digital device to the Wi-Fi®network. If the iPad is new, it must be set up and associated with an Apple ID. Please refer to the AQUALAB 3 help file (metergroup.com/ aqualab3-training) for additional setup configurations, if needed.NOTE: The iPad must use a Wi-Fi or Ethernet…
-
METER PHYTOS 31 Leaf Wetness Sensor User Guide
PHOTOS 31LEAF WETNESS SENSOR PHOTOS 31 QUICKSTART PreparationConfirm that PHOTOS 31 components are intact. For installation, gather a mounting post and either zip ties or 4-40 bolts. Read the full PHOTOS 31 User Manual at metergroup.com/phytos31support. All products have a 30-day satisfaction guarantee. ConnectingPlug into Data Acquisition SystemConnect the stereo plug connector into any METER…
-
METER RT-1 Temperature Sensor User Guide
RT-1 and ECTTEMPERATURE SENSOR RT-1/ECT QUICK START PreparationConfirm that the sensor components are intact. The sensor is completely waterproof, submersible, and designed for continuousoutdoor use. Contact Customer Support for more information. The RT-1 and the ECT sensors are the same sensors that perform different measurements. The RT-1 measures soil temperature,and the ECT is paired with…
-
METER ES-2 Electrical Conductivity + Temperature User Guide
METERES-2Electrical Conductivity + Temperature ES-2 QUICKSTART The ES-2 is designed to measure the electrical conductivity and temperature of water-based solutions. PreparationConfirm that ES-2 components are intact. Gather the necessary pipe fittings and glue or suspension setup for the desired installation type as well as the necessary items for the data acquisition system installation.Read the full…
-
METER HYDROS 21 Water Depth + Temperature + Electrical Conductivity User Guide
HYDROS 21Water Depth + Temperature + Electrical Conductivity HYDROS 21 QUICKSTART PreparationConfirm that HYDROS 21 components are intact. Gather the necessary tools and suspension setup for the desired installation type and a mounting post for the data logger.Determine the installation depth prior to installation. The sensor zero point is 1.5 cm from the bottom of…
